1、REVISIONS LTR DESCRIPTION DATE APPROVED A Add interchangeability statement to page 8. 7 April 1994 Randy Larson B Requirement upgrade. 29 September 1994 Charles Koeller C Add new shroud design. Add CAGE 82316 as source of supply. 18 January 1995 Randy Larson D Changes in NOR incorporated. 3 April 19
2、95 Randy Larson E Changes in NOR incorporated. 7 September 1995 Randy Larson F Changes in NOR incorporated. 23 October 1997 Robert Heber G Dimensional changes to flange. Full detent force to disengage 5 pounds, minimum. Clarify radial misalignment. 5 February 1999 Robert Heber H Relocate dimension “
3、.010 .001” in figure 2. Delete all figure numbers from the table and reference “MIL-STD-348”. 3 May 1999 Robert Heber J PIN and source update. 3 August 2001 Robert Heber K Changes to NOR incorporated 10 September 2002 Robert Heber L Changes to NOR incorporated 17 January 2003 Robert Heber M PIN numb
4、ers for CAGE 00779 updated 18 August 2005 Richard Taylor N Changes to NOR incorporated 1 February 2007 Richard Taylor P Add test pin requirements and reformat. Add source 95077 21 May 2009 Abdonasser M. Abdouni THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. Prepared in accordance with AS
5、ME Y14-100. REV PAGE REV STATUS OF PAGES REV P P P P P P P P P PAGE 1 2 3 4 5 6 7 8 9 PMIC G PREPARED BY DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Ron Gary Original date of drawing 31 March 1994 CHECKED BY TITLE C. W. Koeller CONNECTOR, ELECTRICAL, COAXIAL, RADIO FREQUENCY, SHROUD 2
6、HOLE PIN AND ADAPTER, ELECTRICAL, COAXIAL, RF, SOCKET CONTACT, SERIES SMP TO SMP APPROVED BY Randy Larson SIZE CAGE CODE DWG. NO. 94007 A 037Z3 REV P PAGE 1 OF 9 AMSC N/A 5935-E819-001 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CE
7、NTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 94007 REV P PAGE 2 Inches mm Inches mm .015 0.38 .2555 6.490 .112 2.79 .256 6.50 .135 3.43 .390 9.91 .252 6.40 .400 10.16 .2525 6.414 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. All
8、 undimensioned pictorial configurations are for reference purposes only. 4. Special tools shall be required for assembly. Contact manufacturer. FIGURE 1. General configuration, adapter. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY C
9、ENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 94007 REV P PAGE 3 Inches mm Inches mm Inches mm .002 0.05 .155 3.94 .352 8.94 .005 0.13 .187 4.75 .400 10.16 .045 1.14 .223 5.66 .470 11.94 .073 1.85 .235 5.97 .480 12.19 .098 2.49 .282 7.16 .481 12.22 .102 2.59 .328 8.33 .625 1
10、5.88 Part or Identifying Number (PIN) Dimension A Dimension B Dimension C Dimension D Shroud design 1/ 94007ZSP-3 .328 .187 .098 .480 Full detent 94007ZSP-3L Limited detent 94007ZSP-3S Smooth bore 94007ZSP-4 .481 .223 .102 .625 Full detent 94007ZSP-4L Limited detent 94007ZSP-4S Smooth bore 94007ZSP-
11、5 .282 .165 .073 .400 Full detent 94007ZSP-5L Limited detent 94007ZSP-5S Smooth bore 94007ZSP-6SC .352 .235 .073 .470 Smooth bore 1/ See MIL-STD-348 for interface dimensions. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. All undimensioned pictorial conf
12、igurations are for reference purposes only. 4. Special tools shall be required for assembly. Contact manufacturer. 5. Dimension to be .235 (5.79 mm) .005 (0.13 mm) when using 94007ZSP-6SC. FIGURE 2. General configuration, shroud. Provided by IHSNot for ResaleNo reproduction or networking permitted w
13、ithout license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 94007 REV P PAGE 4 ENGINEERING DATA: Nominal impedance: 50 ohms. Frequency range: DC to 40 GHz. RF leakage: -80 dB to 3 GHz. -65 dB from 3 to 26.5 GHz minimum. Voltage rating: 335 V rms
14、 maximum at sea level. 65 V rms at 70,000 feet. Operating temperature: -65C to +165C. REQUIREMENTS: (All electrical and mechanical requirements shall be maintained during radial misalignment. Requirements of drawing 84148 are applicable.) Dimensions and configurations: See figures 1and 2. Interface
15、dimensions: In accordance with MIL-STD-348A. Force to engage: Full detent: 15 pounds maximum. Limited detent: 10 pounds maximum. Smooth bore: 2 pounds maximum. Force to disengage: 5 pounds minimum (full detent), 2 pounds minimum (limited detent), and .5 pound minimum (smooth bore). Center contact in
16、spection conditions (after heat treat) Oversize test pin: Test pin diameter: .0165 inch +.0001/-.0000 inch. Insertion depth: .065 inch minimum, .070 inch maximum. Number of insertions: 10. Insertion force test: Test pin diameter: .0160 inch +.0001/-.0000 inch. Insertion force: 24 ounces, maximum. In
17、sertion depth: .055 inch minimum, .065 inch maximum. Withdrawal force test: Test pin diameter: .0140 +0000/-.0001 inch. Withdrawal force: 0.5 ounce, minimum. Insertion depth: .055 inch minimum, .065 inch maximum. Radial misalignment: Total radial misalignment between centerlines of connector shroud
18、or mating planes, .010 inch (0.25 mm), min (.020 min (0.51 mm), total for 94007ZSP-6SC). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 94007 REV P PAGE 5 Axial m
19、isalignment: .000/.010 (0.00/0.25 mm). Coupling proof torque: Not applicable. Hermetic seal: Not applicable. Leakage (pressurized connectors): Not applicable. Center contact retention: 1.5 pounds minimum axial force (Socket contact adapter only). Radial torque: Not applicable. Voltage standing wave
20、ratio: DC to 23 gigahertz: 1.10:1 maximum. 23 to 26.5 gigahertz: 1.15:1 maximum. 26.5 to 40 gigahertz: 1.7:1 maximum. VSWR procedure. The VSWR shall be measured in accordance with the following procedure or a method acceptable to the Government. Part should be tested using a Network Analyzer with th
21、e Time Domain (TDR) option installed. This is essential to allow the effect of the adapters to be “gated” out. The recommended network analyzer systems include Hewlett Packard HP 8510. Wiltron 360 or equivalent. The printer/plotter and the computer should be any unit compatible to the system. The de
22、vice under test (DUT) shall consist of DSCC PIN 94007ZCG-1 or PIN 94007ZCG-2 mated at both ends with adapters capable of performing to 40 GHz such as CDI PIN 225-135-1CC (male). 224-135-1CC (female) or M/A Com PIN 224-135-1CC or equivalent. Calibration of the system should be performed using the man
23、ufacturers calibration kits and the recommended calibration procedures. The frequency range shall be DC to 40 GHz. The VSWR calibration test setup shall be verified using the manufacturers verification kits. The calibrated system VSWR shall be less than 1.02 + .001F (F in GHZ). The VSWR of the DUT s
24、hall be measured using the procedures described in the manufacturers operating instructions. The time domain shall then be used to remove the effects of the test adapter. The output shall be generated using the appropriate printer/plotter. Moisture resistance: MIL-STD-202, method 106, except step 7b
25、 shall be omitted. Resistance shall be 1,000 megohms within 5 minutes after removal from humidity (Socket contact adapter only). Contact resistance (in milliohms, maximum): Initial Center contact 6.0 Outer contact 2.0 Dielectric withstanding voltage at sea level: 500 V rms minimum. 125 V rms at 70,0
26、00 feet. (Socket contact adapter only). Vibration, high frequency: MIL-STD-202, method 204, test condition D. Vibration, random: MIL-STD-202, method 214, test condition F, duration 15 minutes, minimum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
27、DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 94007 REV P PAGE 6 Corona level (Socket contact adapter only): : Altitude: 70,000 feet. 190 V rms, minimum. Insulation resistance: 5,000 megohms minimum when tested in accordance with MIL-PRF-39012 (Socket contact
28、 adapter only). Altitude: Sea level to 70,000 feet. Solderability (when applicable): Not applicable. Shock (specified pulse): MIL-STD-202, method 213, test condition I (Socket contact adapter only). Thermal shock: MIL-STD-202, method 107, test condition B (except high temperature to be +165C). RF hi
29、gh potential withstanding voltage: 325 V rms minimum at sea level. Frequency: 5 MHz. Leakage current: Not applicable. Cable retention: Not applicable. Coupling mechanism retention force: Not applicable. Durability: Full detent: 100 cycles. Limited detent: 500 cycles. Smooth bore: 1,000 cycles. RF in
30、sertion loss: .10 Frequency (GHz) dB Part or Identifying Number (PIN): 94007ZCG-* or 94007ZSP-* (see figures 1 and 2). Materials: Contacts and adapter housing: Beryllium copper in accordance with ASTM B196, gold plated to a minimum thickness of 50 microinches (1.27 m) in accordance with MIL-DTL-4520
31、4, type II, grade C, class 1, over 50 microinches (1.27 m) minimum of nickel in accordance with MIL-DTL-38999, class 1. Shroud: Stainless steel passivated. The Government has determined that the DSCC drawing PINs listed below are interchangeable with Gilbert Engineering Co,s “push on” style RF conne
32、ctors. Approved sources of supply. Additional sources will be added as they become available and demonstrate to the Government through testing at this facility that their product meets all the requirements of this drawing and is intermateable with the approved sources below. The vendors listed on th
33、is drawing have reviewed the requirements of this drawing, determined that their product meets all of those requirements and a certificate of compliance has been submitted to DSCC-VAI. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CE
34、NTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE DWG NO. A 037Z3 94007 REV P PAGE 7 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 94007ZCG-1 30990 82316 2J899 00779 95077 P65
35、0-135-1CC 0119-945-1 1100-2020-5450 1056703-1 1290-4008 94007ZCG-2 30990 82316 2J899 00779 95077 P650-135-2CC 0119-969-1 1100-2020-5495 1757023-1 1290-4009 94007ZSP-3 30990 82316 2J899 00779 95077 P670-135-1SF 0119-946-3 9-21802 1056740-1 SF1254-6000 94007ZSP-3L 30990 82316 2J899 00779 95077 P672-13
36、5-1SF 0119-957-3 9-21702 1757024-1 SF1254-6001 94007ZSP-3S 30990 82316 2J899 00779 95077 P673-135-1SF 0119-954-03 9-21902 1757025-1 SF1254-6002 94007ZSP-4 30990 82316 2J899 00779 95077 P670-135-2SF 0119-948-3 9-21804 1056741-1 SF1254-6003 94007ZSP-4L 30990 82316 2J899 00779 95077 P672-135-2SF 0119-8
37、33-3 9-21720 1757026-1 SF1254-6004 94007ZSP-4S 30990 82316 2J899 00779 95077 P673-135-2SF 0119-955-3 9-21908 1757027-1 SF1254-6005 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH 43218-3990 SIZE CAGE CODE
38、DWG NO. A 037Z3 94007 REV P PAGE 8 1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met. Vendor CAGE Vendor name number and address 30990 Carlisle Interconnect Technologies 2400 Grand Avenue Long Beach, CA 90815 82316 Corning Gilbert, Inc. 5310 W.
39、 Camelback Road Glendale, AZ 85301 2J899 Dynawave Incorporated 135 Ward Hill Avenue Haverhill, MA 01835 00779 TYCO Electronics P.O. Box 3608 Harrisburg, PA 17105 95077 SV Microwave, Inc. 2400 Centrepark West Dr. WPB, FL 33409 DSCC drawing PIN 1/ Vendor CAGE number Vendor reference PIN 94007ZSP-5 309
40、90 82316 2J899 00779 95077 P670-135-3SF 0119-950-3 9-21801 1056742-1 SF1254-6006 94007ZSP-5L 30990 82316 2J899 00779 95077 P672-135-3SF 0119-821-3 9-21701 1757028-1 SF1254-6007 94007ZSP-5S 30990 82316 2J899 00779 95077 P673-135-3SF 0119-953-3 9-21905 1757029-1 SF1254-6008 94007ZSP-6SC 30990 82316 2J899 00779 95077 P671-135-1SF 0119-844-3 9-21935 1757030-1 SF1254-6009 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
