1、 REVISIONS LT DESCRIPTION DATE APPROVED A Five year document review. Update to present DoD policy requirements 6 Feb 2004 K. Cottongim B Add pure tin, manufacturer eligibility, and high power pulse paragraphs. Editorial changes throughout. 3 Dec 2010 M. Radecki Prepared in accordance with ASME Y14.1
2、00 Source control drawing REV STATUS OF PAGES REV B B B B B B PAGES 1 2 3 4 5 6 PMIC N/A PREPARED BY Dennis L. Cross DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 23 November 1998 CHECKED BY Andrew R. Ernst TITLE RESISTORS, FIXED, FILM (INSULATED), 1/8 WATT APPROVED BY Andrew
3、 R. Ernst SIZE A CODE IDENT. NO. 037Z3 DWG NO. 98020 REV B PAGE 1 OF 6 AMSC N/A 5905-E718 CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DE
4、FENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 98020 REV B PAGE 2 1. SCOPE * 1.1 Scope. This drawing describes the requirements for insulated, fixed, film, 1/8 watt resistors available in 2 percent, 5 percent, and 10 percent resistance tolerances. These resistors ar
5、e capable of full-load operation at an ambient temperature of 70OC. Designers are CAUTIONED on using these resistors in high power pulse applications (see 6.4). 1.2 Part or Identifying Number (PIN). The complete PIN is as follows: 98020- - G 220 | | | | | | Drawing number Tolerance (see 3.3.1) Resis
6、tance value (see 3.3.2) 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents ar
7、e those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-39017 - Resistors, Fixed, Film (Insulated), Nonestablished Reliability, Established Reliability, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-790 - Standard Practice for Established Reli
8、ability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications. MIL-STD-1285 - Marking of Electrical and Electronic Parts. * (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Sta
9、ndardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) * 2.2 Order of precedence. Unless otherwise noted herein or in the event of a conflict between the text of this document and the references cited herein (except for related specification sheets), the tex
10、t of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-39017, and as specified herein
11、. 3.2 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-39017 and herein (see figure 1). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A COD
12、E IDENT NO. 037Z3 DWG NO. 98020 REV B PAGE 3 .150 .020 1.250 .266 1.250 .266 SEE NOTE 3 .016 .002 .187 MAX SEE NOTE 2 .066 .008 LEAD LOCATION AT TRUE POSITION WITHIN .016 DIA NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Maximum length is “clean le
13、ad” to “clean lead”. 3. The end of the body shall be that point at which the body diameter equals the nearest drill size larger than 250 percent of the nominal lead diameter. 4. Lead length for tape and reel packaging shall be 1 inch (25.4 mm) minimum (see 6.2). 5. The pictorial view of the style ab
14、ove does not depict the actual size and is given as representative of the envelope of the item. Slight deviations from the outline shown, which are contained within the envelope, and do not alter the functional aspects of the device are acceptable. FIGURE 1. Fixed, film, resistor. 3.3 Electrical cha
15、racteristics. 3.3.1 Resistance tolerance. The resistance tolerance available shall be (G) 2 percent, (J) 5 percent, and (K) 10 percent. 3.3.2 Resistance. The nominal resistance expressed in ohms is identified by three digits; the first two digits represent significant figures and the last digit spec
16、ifies the number of zeros to follow. Minimum and maximum resistance values shall be as specified in 3.3.3. Resistance values not listed in the “10 to 100“ decade of table I for the appropriate resistance tolerance shall be considered nonconforming to the specification. Inches mm Inches mm .002 0.05
17、.150 3.81 .008 0.20 .187 4.75 .016 0.41 .266 6.76 .020 0.51 1.250 31.75 .066 1.68 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 98020 REV B PAGE 4 TABLE I. Standard
18、resistance values for 10 to 100 decade. (G) (J) (K) (G) (J) (K) (G) (J) (K) 10.0 11.0 12.0 13.0 15.0 16.0 18.0 20.0 10.0 - 12.0 - 15.0 - 18.0 - 22.0 24.0 27.0 30.0 33.0 36.0 39.0 43.0 22.0 - 27.0 - 33.0 - 39.0 - 47.0 51.0 56.0 62.0 68.0 75.0 82.0 91.0 47.0 - 56.0 - 68.0 - 82.0 - 3.3.3 Resistance ran
19、ge. Minimum and maximum resistance values for temperature characteristic of 350 parts per million (ppm) shall be 1.1 megohm and 22 megohms respectively. 3.3.4 Power rating. The power rating shall be 1/8 watt at +70OC. For operation at temperatures higher than +70OC, derate in accordance with figure
20、2. FIGURE 2. Derating curve 3.3.5 Voltage rating. The maximum continuous working voltage shall not exceed 200 volts. 3.3.6 Termination. Termination material shall be in accordance with MIL-PRF-39017. * 3.3.6.1 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both interna
21、lly and externally. Tin content of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass (see 6.3). 3.3.7 Solderability. The requirement for solderability shall be as specified in MIL-PRF-39017. Provided by IHSNot for Resa
22、leNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 98020 REV B PAGE 5 3.4 Marking. Full marking shall be in accordance with MIL-STD-1285, except the resistors shall be marked with the PIN as specif
23、ied herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes is required on the unit package. Due to size limitations this style resistor shall be marked with the following minimum information in the order shown: 8020 - Last four digits of this DSC
24、C drawing number. 826D - Year and week manufactured and the manufacturers code (see qualified products list MIL-PRF-39017 for manufacturers code symbol). G220 - Resistance tolerance and resistance value. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or enviro
25、nmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. * 3.6 Manufacturer eligibility. To be eligible for listing as an approved so
26、urce of supply, a manufacturer shall be listed on the MIL-PRF-39017 Qualified Products List for at least one part, or perform the group A and group B inspections specified herein on a sample agreed upon by the manufacturer and DLA Land and Maritime-VA. * 3.6.1 Certificate of compliance. A certificat
27、e of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.7 Workmanship. Resistors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION * 4.1 Qualification inspection. The qualification
28、 inspection specified in MIL-PRF-39017 and maintained in accordance with MIL-STD-790 is not applicable to this document. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of group A and group B inspections of MIL-PRF-39017. 4.2.2 C
29、ertification. The acquiring activity, at its discretion, may accept a certificate of compliance with group B requirements in lieu of performing group B tests (see 6.2e). 4.3 Product level qualification. The product level qualification specified in MIL-PRF-39017 is not applicable to this document. 4.
30、4 Visual and mechanical examination. Resistors shall be examined to verify that the materials, design, construction, physical dimensions, marking, and workmanship are in accordance with the applicable requirements of MIL-PRF-39017. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging
31、requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained
32、by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the military services system commands. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by cont
33、acting the responsible packaging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 037Z3 DWG NO. 98020 REV B PAGE 6 6. NOTES (This section contains information of a general
34、or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Resistors conforming to this drawing are intended for use when military specifications do not exist. This drawing is intended exclusively to prevent the proliferation of unnecessary duplicate specifications, drawing
35、s, and stock catalog listings. When a military specification exists and the product covered by this drawing has been qualified for listing, this drawing becomes obsolete and will not be used for new design. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete P
36、IN (see 1.2). b. Requirements for delivery: One copy of the conformance inspection results or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Terminal finish. d. Requirements for packaging and packing. e. Whether the manufac
37、turer performs the group B tests or provides certification of compliance with group B requirements (see 4.2.2). * 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime fro
38、m a day to years after manufacture and can develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to inhibit the grow
39、th of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification for Electrodeposited Coatings of Tin). * 6.4 Pulse applications. Designers are CAUTIONED on using the above resistors in high power pulse applications. Since they have not been qualified nor tes
40、ted for such applications, damage and premature failure are possible. These resistors only see a one time pulse (Short-time overload) as part of the group B inspection of MIL-PRF-39017. * 6.5 User of record. Coordination of this document for future revisions is coordinated only with the approved sou
41、rce of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at resistordla.mil or in writing to: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN 850-0552. * 6.6 A
42、pproved source of supply. Approved source of supply is listed herein. Additional sources will be added as they become available. Assistance in the use of this drawing may be obtained online at resistordla.mil or contact DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by t
43、elephone (614) 692-0552 or DSN 850-0552. DLA Land and Maritime drawing PIN Vendor similar designation or type number 1/ Vendor CAGE Vendor name and address 98020-* ERL-05-36 91637 Vishay Dale, Inc. PO Box 609 Columbus, NE 68602-0609 1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance requirements and tests are met. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
