1、REVISIONS LTR DESCRIPTION DATE APPROVED A Update boilerplate paragraphs to current requirements. - PHN 09-02-04 Charles F. Saffle Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV A A A A A A A A A A REV STATUS OF PAGES PAGE 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY P
2、hu H. Nguyen DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY MM DD CHECKED BY Phu H. Nguyen 02-11-05 APPROVED BY Thomas M. Hess TITLE MICROCIRCUIT, DIGITAL, ADVANCED CMOS, 16-BIT BUS TRANSCEIVER WITH THREE-STATE OUTPUTS, TTL COMPATIBLE, MONOLITHIC SILICON SIZE A
3、 CODE IDENT. NO. 16236 DWG NO. V62/03601 REV A PAGE 1 OF 10 AMSC N/A 5962-V28-09 .Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03601 REV A PAGE 2 1. SCOPE 1.1 S
4、cope. This drawing documents the general requirements of a high performance 16-bit bus transceiver with three-state outputs, with an operating temperature range of -40C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor it
5、em drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/03601 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device Type Generic Circuit function 01 SN74ACT16245Q-EP
6、 16-Bit Bus Transceiver with three-state outputs 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline Letter Number of pins JEDEC PUB 95 Package style X 48 JEDEC MO-118 Plastic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes a
7、s provided by the device manufacturer: Finish designator Material: A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other 1.3 Absolute maximum ratings 1/ Supply voltage range (VCC) -0.5 V to 7 V Input voltage range (VI) -0.5 V to VCC+0.5 V 2/ Output voltage range (
8、VO) -0.5 V to VCC+0.5 V 2/ Input clamp current (IIK) (VIVCC) 20 mA Output clamp current (IOK) (VIVCC) 24 mA Continuous output current (IO) (VO= 0 V to VCC) 24 mA Continuous current through VCCor GND 260 mA Maximum power dissipation at TA= 55oC (in still air) 1.2 W 3/ Storage temperature range, Tstg-
9、65oC to 150oC _ 1/ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not imp
10、lied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ The input and output voltage ratings may be exceeded if the input and output ratings are observed. 3/ The maximum package power dissipation is calculated using a junction temperature of 150oC a
11、nd a broad trace length of 750 mils. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03601 REV A PAGE 3 1.4 Recommended operating conditions 4/ 5/ Supply voltage r
12、ange (VCC). +4.5 V to +5.5 V 6/ Input voltage range (VIN) . +0.0 V to VCCOutput voltage range (VOUT). +0.0 V to VCCMinimum high-level input voltage (VIH) 2.0 V Maximum low level input voltage (VIL) . 0.8 V Maximum high level output current (IOH) . -16 mA Maximum low level output current (IOL) . 16 m
13、A Input transition rise or fall rate (t/v) . 0 to 10 ns/V Ambient operating temperature (TA) . -40oC to 125oC 2. APPLICABLE DOCUMENTS JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the Electronic Industries Alliance, 2500 Wilso
14、n Boulevard, Arlington, VA 22201-3834 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code or logo B. Pin 1 identifier C. ESDS identifica
15、tion (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3,
16、 1.4 and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline(s). The case outline (s) shall be as shown in 1.2.2 and figure 1. 3.5.2 Block diagram. The block diagram shall be as
17、shown in figure 2. 3.5.3 Terminal connections. The terminal connections shall be as shown in figure 3. 3.5.4 Timing waveforms. The timing waveforms shall be as shown in figure 4. _ 4/ Unused inputs should be tied to VCCthrough a pullup resistor of approximately 5 k or greater to keep them from float
18、ing. Refer to the device manufacturers application report. 5/ Use of this product beyond the manufacturers design rules or stated parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. 6/ All VCCand
19、 GND pins must be connected to the proper-voltage power supply. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03601 REV A PAGE 4 TABLE I. Electrical performance
20、characteristics. 1/ Test Symbol Test conditions unless otherwise specified VCCTA at Device type Limits Unit Min Max25C 4.40 4.5 V -40C to +125C 4.40 25C 5.40 IOH= -50 A 5.5 V -40C to +125C 5.40 25C 3.94 4.5 V -40C to +125C 3.94 25C 4.94 IOH= -16 mA 5.5 V -40C to +125C 4.94 High level output voltage
21、VOHIOH= -24 mA 2/ 5.5 V -40C to +125C 3.85 V 25C 0.10 4.5 V -40C to +125C 0.10 25C 0.10 IOL= 50 A 5.5 V -40C to +125C 0.10 25C 0.36 4.5 V -40C to +125C 0.50 25C 0.36 IOL= 16 mA 5.5 V -40C to +125C 0.50 Low level output voltage IOL= 24 mA 2/ 5.5 V -40C to +125C 0.50 V 25C 0.10 Input current (Control
22、inputs) IIVI= VCCor GND 5.5 V -40C to +125C 1 A 25C 0.50 Three-state output leakage current (A 0r B ports) 3/ IOZVO= VCCor GND 5.5 V -40C to +125C 10 A 25C 8 Quiescent supply current ICC VI = VCC or GND , IO= 0 5.5 V -40C to +125C 160 A 25C 0.9 Quiescent supply current delta 4/ ICCOne input at 3.4 V
23、, Other inputs at GND or VCC5.5 V -40C to +125C 1 mA Input capacitance (Control inputs) CIVI= VCCor GND 5.0 V 25C 4.5 TYP pF Output capacitance (A or B ports) CIOVO= VCCor GND 5.0 V 25C 16 TYP pF Output enabled 52 TYP Power capacitance per transceiver CPDCL= 50 pF f = 1 MHz Output disabled 5.0 V 25C
24、 01 10 TYP pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03601 REV A PAGE 5 TABLE I. Electrical performance characteristics. 1/
25、 Test Test conditions unless otherwise specified VCCTA at Device type Limits Unit Symbol From (Input) To (Output) Min Max 25C 3.2 9.3 tPLH 5/ -40C to +125C 3.2 11.5 25C 2.6 9.2 tPHL A or B B or A 5/ -40C to +125C 2.6 11.1 25C 2.7 9.1 tPZH 5/ -40C to +125C 2.7 10.9 25C 3.4 10.5 tPZL G B or A 5/ -40C
26、to +125C 3.4 12.6 25C 5.8 11.6 tPHZ 5/ -40C to +125C 5.8 13.4 25C 5.5 10.8 Propagation delay time tPLZG B or A 5/ -40C to +125C 01 5.5 12.7 ns Notes: 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature r
27、ange. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Not more than one output should be tested at a time, and
28、 the duration of the test should not exceed 10 ms. 3/ For I/O ports, the parameter IOZincludes the input leakage current II. 4/ This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or VCC. 5/ VCC= 4.5 V to 5.5 V Provided by IHSNot f
29、or ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03601 REV A PAGE 6 Case X Inches Millimeters Symbol Min Max Min Max A 0.110 2.79 A1 0.008 0.20 b 0.008 0.013 0.20 0.34 D 0.620 0.630 15
30、.75 16.00 E 0.395 0.420 10.03 10.67 E1 0.291 0.299 7.39 7.59 e 0.025 Typ 0.635 Typ L 0.020 0.040 0.51 1.02 L1 0.010 0.25 L2 0.005 0.010 0.13 0.25 FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS
31、COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03601 REV A PAGE 7 Function table Control Inputs G DIR Operation L L B data to A bus L H A data to B bus H X Isolation L = Low H = High X = Dont care FIGURE 2. Block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted w
32、ithout license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03601 REV A PAGE 8 Terminal number Terminal Symbol Terminal number Terminal Symbol 1 1DIR 25 2 G 2 1B1 26 2A8 3 1B2 27 2A7 4 GND 28 GND 5 1B3 29 2A6 6 1B4 30 2A5 7 VCC31 VCC8 1B5 32 2A4
33、 9 1B6 33 2A3 10 GND 34 GND 11 1B7 35 2A2 12 1B8 36 2A1 13 2B1 37 1A8 14 2B2 38 1A7 15 GND 39 GND 16 2B3 40 1A6 17 2B4 41 1A5 18 VCC42 VCC19 2B5 43 1A4 20 2B6 44 1A3 21 GND 45 GND 22 2B7 46 1A2 23 2B8 47 1A1 24 2DIR 48 1 G FIGURE 3. Terminal connections. Provided by IHSNot for ResaleNo reproduction
34、or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/03601 REV A PAGE 9 Test S1 tPLH / tPHLOpen tPLZ/ tPZL2 x VCCtPHZ/ tPZHGND Notes: 1/ CL includes probe and jig capacitance. 2/ Waveform 1 is for an output with i
35、nternal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control 3/ All impulses are supplied by generators having the following characteristics: PRR
36、 1 MHz, ZO= 50 , tr= 3 ns, tf= 3 ns. 4/ The outputs are measured one at a time with one input transition per measurement. FIGURE 4. Timing waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE
37、A CODE IDENT NO. 16236 DWG NO. V62/03601 REV A PAGE 10 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic
38、 sensitive devices, classification, packaging, and labeling of moisture sensitive devices as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge s
39、ensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the righ
40、t to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. Vendor
41、 item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top-Side Marking V62/03601-01XE 01295 SN74ACT16245QDLREP ACT16245QEP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CAGE
42、 code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
