1、 REVISIONSLTR DESCRIPTION DATE APPROVEDA Update boilerplate paragraphs to current requirements. - PHN 11-04-19 David J. Corbett CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing RE
2、V PAGE REV PAGE REV STATUS OF PAGES REV A A A A A A A A A A A PAGE 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Charles F. Saffle DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO Original date of drawing CHECKED BY Charles F. Saffle TITLE MICROCIRCUIT, DIGITAL, ADVANCED BIPOLAR CMOS, 3.3-V ABT 16-BIT
3、BUFFER/DRIVER WITH 3-STATE OUTPUTS, MONOLITHIC SILICON YY-MM-DD 04-04-21 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/04708 REV A PAGE 1 OF 11 AMSC N/A 5962-V042-11 .Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPL
4、Y CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04708 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 3.3-V ABT 16-bit buffer/driver with 3-state outputs microcircuit, with an operating temperature range of -40C to +85C
5、. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/04708 - 01 X E Drawing Device type Case outline Lead finis
6、h number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 SN74LVTH162244-EP 3.3-V ABT 16-bit buffer/driver with 3-state outputs 1.2.2 Case outline. The case outline are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 48
7、 MO-153 Plastic small-outline1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plateC Gold plateD PalladiumE Gold flash palladium Z Other Provided by IHSNot for ResaleNo
8、reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04708 REV A PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) . -0.5 V to 4.6 V Input voltage range (VI) . -0.5 V to 7 V 2/ Voltag
9、e range applied to any output in the high-impedance or power-off state (VO) . -0.5 V to 7 V 2/ Voltage range applied to any output in the high state (VO) . -0.5 V to VCC+ 0.5 V 2/ Current into any output in the low state (IO) . 30 mA Current into any output in the high state (IO) . 30 mA 3/ Input cl
10、amp current (IIK) (VI 0) -50 mA Output clamp current (IOK) (VO 0) . -50 mA Package thermal impedance (JA) . 70C/W 4/ Storage temperature range (TSTG) . -65C to 150C 1.4 Recommended operating conditions. 5/ 6/ Supply voltage range (VCC) . 2.7 V to 3.6 V Minimum high level input voltage (VIH) 2.0 V Ma
11、ximum low level input voltage (VIL) . 0.8 V Maximum input voltage (VI) . 5.5 V Maximum high level output current (IOH) . -12 mA Maximum low level output current (IOL) . 12 mA Maximum input transition rise or fall rate (t/v) (Outputs enabled) 10 ns/V Minimum power-up ramp rate (t/VCC) 200 s/V Operati
12、ng free-air temperature range (TA) -40C to +85C 1/ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended
13、operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 3/ This current flows only when the out
14、put is in the high state and VO VCC. 4/ The package thermal impedance is calculated in accordance with JESD 51-7. 5/ All unused control inputs of the device must be held at VCCor GND to ensure proper device operation. 6/ Use of this product beyond the manufacturers design rules or stated parameters
15、is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CO
16、DE IDENT NO. 16236 DWG NO. V62/04708 REV A PAGE 4 2. APPLICABLE DOCUMENTS ELECTRONICS INDUSTRIES ALLIANCE (EIA) JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices JEDEC STD 51-7 - High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages (Copies of these d
17、ocuments are available online at http:/www.eia.org or from the Electronic Industries Alliance, Technology Strategy & Standards Department, 2500 Wilson Boulevard, Arlington, VA 22201.) 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as sho
18、wn in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The
19、 maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. Th
20、e case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Truth table. The truth table shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4 Terminal connections. The terminal connections shall be as shown in figure 4. 3.5.5 Test circuit and t
21、iming waveforms. The test circuit and timing waveforms shall be as shown in figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04708 REV A PAGE 5 TABLE I. E
22、lectrical performance characteristics. 1/ Test Symbol Conditions VCCTemperature, TADevice type Limits Unit Min Max Input clamp voltage VIKII= -18 mA 2.7 V 25C, -40C to 85C All -1.2 V High level output voltage VOHIOH= -12 mA 3 V 2 V Low level output voltage VOLIOL= 12 mA 3 V 0.8 V Input current IIVI=
23、 5.5 V 0 V or 3.6 V 10 A Control inputs. VI= VCCor GND 3.6 V 1 Data inputs. VI= VCC1 Data inputs. VI= 0 V -5 Input/output power-off leakage current IoffVIor VO= 0 to 4.5 V 0 V 100 A Input current (hold) II(hold)Data inputs. VI= 0.8 V 3 V 75 AData inputs. VI= 2 V -75 Data inputs. VI= 0 V to 3.6 V 3.6
24、 V 2/ +500 -750 3-state output current high IOZHVO= 3 V 3.6 V 5 A 3-state output current low IOZLVO= 0.5 V 3.6 V -5 A 3-state output current power-up IOZPUVO= 0.5 V to 3 V OE = dont care 0 V to 1.5 V 100 A 3-state output current power-down IOZPDVO= 0.5 V to 3 V OE = dont care 1.5 V to 0 V 100 A See
25、footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04708 REV A PAGE 6 TABLE I. Electrical performance characteristics - Continued. Test Sym
26、bol Conditions VCCTemperature, TADevice type Limits Unit Min Max Quiescent supply current ICCOutputs high. VI= VCCor GND IO= 0 A 3.6 V 25C, -40C to 85C All 0.19 mA Outputs low. VI= VCCor GND IO= 0 A 5 Outputs disabled. VI= VCCor GND IO= 0 A 0.19 Quiescent supply current delta ICC3/ One input at VCC
27、0.6 V, Other inputs at VCCor GND 3 V to 3.6 V 0.2 mA Input capacitance CiVI= 3 V or 0 V 3.3 V 25C 4 TYP pF Output capacitance CoVO= 3 V or 0 V 9 TYP pF Propagation delay time, A to Y tPLHCL= 50 pF See figure 5. 2.7 V 25C, -40C to 85C 4.8 ns 3.3 V 0.3 V 1.4 4 tPHL2.7 V 4.13.3 V 0.3 V 1.2 3.6 Propagat
28、ion delay time, output enable, OE to Y tPZH2.7 V 6.5 ns 3.3 V 0.3 V 1.2 5.1 tPZL2.7 V 5.83.3 V 0.3 V 1.4 4.5 Propagation delay time, output disable, OE to Y tPHZ2.7 V 5.4 ns 3.3 V 0.3 V 2.2 5 tPLZ2.7 V 5.43.3 V 0.3 V 2 5 Output skew tsk(o)CL= 50 pF 3.3 V 0.3 V 0.5 ns 1/ Testing and other quality con
29、trol techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product
30、 performance is assured by characterization and/or design. 2/ This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another. 3/ This is the increase in supply current for each input that is at the specified TTL voltage level,
31、 rather than VCCor GND. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04708 REV A PAGE 7 Case X Dimensions Symbol Millimeters Inches Symbol Millimeters Inches Mi
32、n Max Min Max Min Max Min Max A - 1.20 - .047 E1 6.00 6.20 .236 .244 A1 0.05 0.15 .002 .006 e 0.50 BSC .020 BSC b 0.17 0.27 .007 .011 L 0.50 0.75 .020 .030 D 12.40 12.60 .488 .496 L1 0.25 TYP .010 TYP E 7.90 8.30 .311 .327 L2 0.15 NOM .006 NOM NOTES: 1. All linear dimensions are in millimeters (inch
33、es). 2. This case outline is subject to change without notice. 3. Body dimensions do not include mold flash or protrusion, not to exceed 0.15 millimeters (0.006 in). 4. Fall within JEDEC MO-153. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
34、nse from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04708 REV A PAGE 8 (each 4-bit buffer) Inputs Output OE A Y L L H H L X H L Z H = High voltage level L = Low voltage level X = Immaterial Z = High-impedance state FIGURE 2. Truth table. FIGURE 3.
35、Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04708 REV A PAGE 9 Device type 01 Case outline X Terminal number Terminal symbol Terminal number Ter
36、minal symbol 1 1OE 25 3OE 2 1Y1 26 4A4 3 1Y2 27 4A34 GND 28 GND 5 1Y3 29 4A2 6 1Y4 30 4A17 VCC31 VCC8 2Y1 32 3A49 2Y2 33 3A3 10 GND 34 GND 11 2Y3 35 3A2 12 2Y4 36 3A113 3Y1 37 2A4 14 3Y2 38 2A315 GND 39 GND 16 3Y3 40 2A2 17 3Y4 41 2A118 VCC42 VCC19 4Y1 43 1A4 20 4Y2 44 1A321 GND 45 GND 22 4Y3 46 1A2
37、 23 4Y4 47 1A124 4OE 48 2OE FIGURE 4. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04708 REV A PAGE 10 NOTES: 1. CLincludes probe and jig
38、capacitance. 2. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. 3. All input pulses are supplied
39、by generators having the following characteristics: PRR 10 MHz, ZO= 50 , tr 2.5 ns, and tf 2.5 ns. 4. The outputs are measured one at a time with one input transition per measurement. FIGURE 5. Test circuit and timing waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted wi
40、thout license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04708 REV A PAGE 11 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal
41、 documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance wi
42、th the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics
43、of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee
44、 of present or continued availability as a source of supply for the item. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number Top side marking V62/04708-01XE 01295 CLVTH162244IDGGREP LH162244EP 1/ The vendor item drawing establishes an administrative
45、 control number for identifying the item on the engineering documentation. CAGE code Source of supply 01295 Texas Instruments, Inc. Semiconductor Group8505 Forest Lane P.O. Box 660199 Dallas, TX 75243 Point of contact: U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
