1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Add device type 02. - CFS 06-07-18 Thomas M. Hess B Update boilerplate paragraphs to current requirements. - PHN 13-09-12 Thomas M. Hess CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared i
2、n accordance with ASME Y14.24 Vendor item drawing REV PAGE REV PAGE REV STATUS OF PAGES REV B B B B B B B B B B B B B PAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Charles F. Saffle DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing CHECKED BY Charles F. Saf
3、fle TITLE MICROCIRCUIT, DIGITAL, ADVANCED LOW-VOLTAGE CMOS, OCTAL 16-BIT BUS TRANSCEIVER WITH 3-STATE OUTPUTS, MONOLITHIC SILICON YY-MM-DD 04-12-20 APPROVED BY Thomas M. Hess SIZE A CODE IDENT. NO. 16236 DWG NO. V62/04763 REV B PAGE 1 OF 13 AMSC N/A 5962-V084-13 Provided by IHSNot for ResaleNo repro
4、duction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance 16-bit bus transceiver with 3-state outputs
5、 microcircuit, with an operating temperature range of -40C to +85C for device 01, and -55C to +125C for device 02. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturers PIN is the item of identification. The vendor item drawing establishes an administrative control number for iden
6、tifying the item on the engineering documentation: V62/04763 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device type Generic Circuit function 01 SN74ALVCH16245-EP 16-bit bus transceiver with 3-state outputs 02 SN74ALVCH16245-
7、EP 16-bit bus transceiver with 3-state outputs 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 48 JEDEC MO-118 Plastic small-outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as
8、provided by the device manufacturer: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO S
9、IZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 3 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) . -0.5 V to 4.6 V Input voltage range (VI): Except I/O ports. -0.5 V to 4.6 V 2/ I/O ports -0.5 V to 4.6 V 2/ 3/ Output voltage range (VO) . -0.5 V to VCC+ 0.5 V 2/ 3/ Input clamp cu
10、rrent (IIK) (VI 0) 50 mA Output clamp current (IOK) (VO 0) . 50 mA Continuous output current (IO) . 50 mA Continuous current through each VCCor GND 100 mA Package thermal impedance (JA) . 63C/W 4/ Storage temperature range (TSTG) . -65C to +150C 1.4 Recommended operating conditions. 5/ Supply voltag
11、e range (VCC) . 1.65 V to 3.6 V Minimum high-level input voltage (VIH): VCC= 1.65 V to 1.95 V . 0.65 x VCCVCC= 2.3 V to 2.7 V . 1.7 V VCC= 2.7 V to 3.6 V . 2 V Maximum low-level input voltage (VIL): VCC= 1.65 V to 1.95 V . 0.35 x VCCVCC= 2.3 V to 2.7 V . 0.7 V VCC= 2.7 V to 3.6 V . 0.8 V Input volta
12、ge range (VI) . 0 V to VCCOutput voltage range (VO) . 0 V to VCCMaximum high-level output current (IOH): VCC= 1.65 V -4 mA VCC= 2.3 V -12 mA VCC= 2.7 V -12 mA VCC= 3 V . -24 mA Maximum low-level output current (IOL): VCC= 1.65 V 4 mA VCC= 2.3 V 12 mA VCC= 2.7 V 12 mA VCC= 3 V . 24 mA Maximum input t
13、ransition rise or fall rate (t/v) . 10 ns/V Operating free-air temperature range (TA): Device 01 -40C to +85C Device 02 -55C to +125C 1/ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of
14、the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ The input negative-voltage and output voltage ratings may be exceeded if th
15、e input and output current ratings are observed. 3/ This value is limited to 4.6 V maximum. 4/ The package thermal impedance is calculated in accordance with JESD 51-7. 5/ All unused inputs of the device must be held at VCCor GND to ensure proper device operation. Provided by IHSNot for ResaleNo rep
16、roduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 4 2. APPLICABLE DOCUMENTS JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JEP95 Registered and Standard Outlines for Semiconductor D
17、evices JESD51-7 High Effective Thermal Conductivity Test Board for Leaded Surface Mount Packages (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10th Street, Suite 240S, Arlington, VA 22201-2107). 3. REQUIREMENTS 3.1
18、 Marking. Parts shall be permanently and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufactur
19、ers part number and with items A and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, co
20、nstruction, and physical dimensions are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Function table. The function table shall be as shown in figure 2. 3.5.3 Logic diagram. The logic diagram shall be as shown in figure 3. 3.5.4
21、 Terminal connections. The terminal connections shall be as shown in figure 4. 3.5.5 Timing waveforms and test circuit. The timing waveforms and test circuit shall be as shown in figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPL
22、Y CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions Device 01: -40C TA +85C Device 02: -55C TA +125C unless otherwise specified VCCDevice type Limits Unit Min Max High level output vol
23、tage VOHIOH= -100 A 1.65 V to 3.6 V All VCC 0.2 V IOH= -4 mA 1.65 V 1.2 IOH= -6 mA 2.3 V 2 IOH= -12 mA 2.3 V 1.7 2.7 V 2.2 3 V 2.4 IOH= -24 mA 3 V 2 Low level output voltage VOLIOL= 100 A 1.65 V to 3.6 V 0.2 V IOL= 4 mA 1.65 V 0.45 IOL= 6 mA 2.3 V 0.4 IOL= 12 mA 2.3 V 0.7 2.7 V 0.4 IOL= 24 mA 3 V 0.
24、55 Input current IIVI= VCCor GND 3.6V 5 A Input hold current II(hold)VI= 0.58 V 1.65 V 25 A VI= 1.07 V 1.65 V -25 VI= 0.7 V 2.3 V 45 VI= 1.7 V 2.3 V -45 VI= 0.8 V 3 V 75 VI= 2 V 3 V -75 VI= 0 to 3.6 V 2/ 3.6 V 500 Off-state output current IOZ3/ VO= VCCor GND 3.6 V 10 A Quiescent supply current ICCVI
25、= VCCor GND IO= 0 A 3.6 V 40 A Quiescent supply current delta ICCOne input at VCC 0.6 V, Other inputs at VCCor GND 3 V to 3.6 V 750 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUM
26、BUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 6 TABLE I. Electrical performance characteristics - Continued. 1/ Test Symbol Conditions Device 01: -40C TA +85C Device 02: -55C TA +125C unless otherwise specified VCCDevice type Limits Unit Min Max Input capacitance CIControl input
27、s VI= VCCor GND TA= 25C 3.3 V All 4 TYP pF Input/output capacitance CiOA or B ports VO= VCCor GND TA= 25C 3.3 V 8 TYP pF Power dissipation capacitance CpdOutputs enabled CL= 50 pF f = 10 MHz TA= 25C 2.5 V 22 TYP pF 3.3 V 29 TYP Outputs disabled CL= 50 pF f = 10 MHz TA= 25C 2.5 V 4 TYP 3.3 V 5 TYP Pr
28、opagation delay time, A or B to B or A tpdSee figure 5. 2.5 V 0.2 V 01 1 3.7 ns 2.7 V 3.6 3.3 V 0.3 V 1 3 Propagation delay time, output enable, OE to A or B tenSee figure 5. 2.5 V 0.2 V 1 5.7 ns 2.7 V 5.4 3.3 V 0.3 V 1 4.4 Propagation delay time, output disable, OE to A or B tdisSee figure 5. 2.5 V
29、 0.2 V 1 5.2 ns 2.7 V 4.6 3.3 V 0.3 V 1 4.1 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 7 TABLE I. Electrical p
30、erformance characteristics - Continued. 1/ Test Symbol Conditions Device 01: -40C TA +85C Device 02: -55C TA +125C unless otherwise specified VCCDevice type Limits Unit Min Max Propagation delay time, A or B to B or A tpdSee figure 5. 2.5 V 0.2 V 02 1 4.5 ns 3.3 V 0.3 V 1 4.0 Propagation delay time,
31、 output enable, OE to A or B tenSee figure 5. 2.5 V 0.2 V 1 8.2 ns 3.3 V 0.3 V 1 5.5 Propagation delay time, output disable, OE to A or B tdisSee figure 5. 2.5 V 0.2 V 1 7.5 ns 3.3 V 0.3 V 1 5.0 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product
32、 performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ This is the
33、 bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another. 3/ For I/O ports, the parameter IOZincludes the input leakage current. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFE
34、NSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 8 Case X NOTES: 1. This drawing is subject to change without notice. 2. Falls within JEDEC MO-118. 3. All linear dimensions are shown in inches (millimeters). Millimeters equivalents are given for gen
35、eral information only. 4. Body dimensions do not include mold flash or protrusion not to exceed 0.006 inches (0.15 millimeters). FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SI
36、ZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 9 Case X Symbol Dimensions Inches Millimeters Min Max Min Max A - 0.110 - 2.79 A1 0.008 - 0.20 - b 0.008 0.0135 0.203 0.343 D 0.620 0.630 15.75 16.00 E 0.395 0.420 10.03 10.67 E1 0.291 0.299 7.39 7.59 e 0.025 BSC 0.635 BSC L 0.020 0.040 0.51 1.0
37、2 L1 0.010 TYP 0.25 TYP L2 0.005 0.010 0.13 0.25 FIGURE 1. Case outline - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 10 (each 8-bi
38、t section) Inputs Operation OE DIR L L H H L X B data to A bus A data to B bus Isolation H = High voltage level L = Low voltage level X = Immaterial FIGURE 2. Function table. FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DE
39、FENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 11 Device types: 01 and 02 Case outlines: X Terminal number Terminal symbol Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 1DIR 1B1 1B2 GND 1B3 1B4 VC
40、C1B5 1B6 GND 1B7 1B8 2B1 2B2 GND 2B3 2B4 VCC2B5 2B6 GND 2B7 2B8 2DIR 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 2OE 2A8 2A7 GND 2A6 2A5 VCC2A4 2A3 GND 2A2 2A1 1A8 1A7 GND 1A6 1A5 VCC1A4 1A3 GND 1A2 1A1 1OE FIGURE 4. Terminal connections. Provided by IHSNot for ResaleNo r
41、eproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 12 NOTES: 1. CLincludes probe and jig capacitance. 2. Waveform 1 is for an output with internal conditions such that the output is
42、low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. 3. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO= 50. 4. The outputs are m
43、easured one at a time, with one input transition per measurement. 5. tPLHand tPHLare the same as tpd. 6. tPZLand tPZHare the same as ten. 7. tPLZand tPHZare the same as tdis. FIGURE 5. Timing waveforms and test circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without lic
44、ense from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/04763 REV B PAGE 13 4. VERIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal document
45、ation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the ma
46、nufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the de
47、vice manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control
