1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Update boilerplate paragraphs to current requirements. - ro 12-06-06 C. SAFFLE CURRENT DESIGN ACTIVITY CAGE CODE 16236 HAS CHANGED NAMES TO: DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 Prepared in accordance with ASME Y14.24 Vendor item drawing REV PAGE
2、 REV PAGE REV STATUS OF PAGES REV A A A A A A A A A A A A PAGE 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 Original date of drawing YY-MM-DD CHECKED BY TOM HESS TITLE MICROCIRCUIT, LINEAR, LOW DROPOUT VOLTAGE REGULATOR, MONOLI
3、THIC SILICON 06-07-28 APPROVED BY RAYMOND MONNIN SIZE A CODE IDENT. NO. 16236 DWG NO. V62/06644 REV A PAGE 1 OF 12 AMSC N/A 5962-V058-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT
4、NO. 16236 DWG NO. V62/06644 REV A PAGE 2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance low dropout voltage regulator microcircuit, with an operating temperature range of -55C to +125C. 1.2 Vendor Item Drawing Administrative Control Number. The manufacturer
5、s PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: V62/06644 - 01 X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) 1.2.1 Device type(s). Device
6、 type Generic Output voltages Circuit function 01 TPS73201-EP 1.2 V 1/ Low dropout voltage regulator 02 TPS73215-EP 1.5 V Low dropout voltage regulator 03 TPS73216-EP 1.6 V Low dropout voltage regulator 04 TPS73218-EP 1.8 V Low dropout voltage regulator 05 TPS73225-EP 2.5 V Low dropout voltage regul
7、ator 06 TPS73230-EP 3.0 V Low dropout voltage regulator 07 TPS73233-EP 3.3 V Low dropout voltage regulator 08 TPS73250-EP 5.0 V Low dropout voltage regulator 1.2.2 Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 5 MO-178-AA Pla
8、stic small outline 1.2.3 Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacture: Finish designator Material A Hot solder dip B Tin-lead plate C Gold plate D Palladium E Gold flash palladium Z Other 1/ For fixed 1.2 V operation, tie FB to
9、OUT. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06644 REV A PAGE 3 1.3 Absolute maximum ratings. 2/ Input voltage range (VIN) . -0.3 V to 6 V Enable voltage r
10、ange (VEN) . -0.3 V to 6 V Output voltage range (VOUT) . -0.3 V to 5.5 V Peak output current Internally limited Output short circuit duration . Indefinite Continuous total power dissipation (PD) See 1.5, dissipation ratings table Storage temperature range (TSTG) -65C to +150C Electrostatic discharge
11、 rating (ESD): Human body model 2 kV Charged device model . 500 V 1.4 Recommended operating conditions. 3/ Ambient temperature range (TA) -55C to +125C 1.5 Power dissipation ratings. 4/ Package Board RJCRJADerating factor above TA= 25C TA 25C power rating TA= 70C power rating TA= 85C power rating TA
12、= 125C power rating Case X Low K 5/ 64C/W 255C/W 3.9 mW/C 450 mW 275 mW 215 mW 58 mW High K 6/ 64C/W 180C/W 5.6 mW/C 638 mW 388 mW 305 mW 83 mW 2/ Stresses beyond those listed under “absolute maximum rating” may cause permanent damage to the device. These are stress ratings only, and functional oper
13、ation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 3/ Use of this product beyond the manufacturers design rules or state
14、d parameters is done at the users risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. 4/ See power dissipation in the applications section of the vendor datasheet for more information related to thermal design. 5/ The JEDEC Low
15、-K (1s) board design used to derive this data was a 3 inch x 3 inch, two layer board with 2 ounce copper traces on top of the board. 6/ The JEDEC High-K (2s2p) board design used to derive this data was a 3 inch x 3 inch, multilayer board with 1 ounce internal power and ground planes and 2 ounce copp
16、er traces on the top and bottom of the board. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06644 REV A PAGE 4 2. APPLICABLE DOCUMENTS JEDEC Solid State Technolo
17、gy Association JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Applications for copies should be addressed to the JEDEC Office, 3103 North 10th Street, Suite 240-S, Arlington, VA 22201-2107 or online at http:/www.jedec.org) 3. REQUIREMENTS 3.1 Marking. Parts shall be permane
18、ntly and legibly marked with the manufacturers part number as shown in 6.3 herein and as follows: A. Manufacturers name, CAGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturers part number and with items A
19、 and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensi
20、ons are as specified herein. 3.5 Diagrams. 3.5.1 Case outline. The case outline shall be as shown in 1.2.2 and figure 1. 3.5.2 Terminal connections. The terminal connections shall be as shown in figure 2. 3.5.3 Block diagrams. The block diagrams shall be as shown in figure 3. Provided by IHSNot for
21、ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06644 REV A PAGE 5 TABLE I. Electrical performance characteristics. 1/ Test Symbol Conditions 2/Temperature, TADevice type Limits Unit Min
22、 Max Input voltage range VIN3/ -55C to +125C All 1.7 5.5 V Internal reference VFB+25C 01 1.198 1.21 V Output voltage range VOUT4/ -55C to +125C 01 VFB5.5 - VDOV Accuracy 3/ VOUTNominal +25C All 0.5 typical % VIN, IOUT, and T, VOUT+ 0.5 V VIN 5.5 V, 10 mA IOUT 250 mA -55C to +125C All -1 +1 % Line re
23、gulation 3/ VOUT% / VINVOUT(nom)+ 0.5 V VIN 5.5 V +25C All 0.01 typical %/V Load regulation VOUT% / 1 mA IOUT 250 mA +25C All 0.002 typical %/mA IOUT10 mA IOUT 250 mA 0.0005 typical Dropout voltage 5/ VDO(VIN= VOUT(nom) 0.1 V), IOUT= 250 mA -55C to +125C All 150 mV Output impedance in dropout ZO(DO)
24、 1.7 V VIN VOUT+ VDO+25C All 0.25 typical Output current limit ICLVOUT= 0.9 X VOUT(nom)-55C to +125C All 250 600 mA Short circuit current ISCVOUT= 0 V +25C All 300 typical mA Reverse leakage 6/ current (-IIN) IREVVEN 0.5 V, 0 V VIN VOUT-55C to +125C All 15 A Ground pin current IGNDIOUT= 10 mA (IQ) -
25、55C to +125C All 550 A IOUT= 250 mA 950 Shutdown current (IGND) ISHDNVEN 0.5 V, VOUT VIN 5.5 V -55C to +125C All 1 A FEEDBACK (FB) pin current IFB-55C to +125C 01 0.45 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-D
26、EFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06644 REV A PAGE 6 TABLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 2/Temperature, TADevice type Limits Unit Min Max Power supply rejection ratio PSRR f = 100 Hz, IOUT= 250 mA +2
27、5C All 58 typical dB (ripple rejection) f = 10 kHz, IOUT= 250 mA 37 typical Output noise voltage VNCOUT= 10 F, no CNR, BW = 10 Hz to 100 kHz +25C All 27 x VOUTtypical VRMSCOUT= 10 F, CNR = 0.01 F, BW = 10 Hz to 100 kHz 8.5 x VOUTtypical Start up time tSTRVOUT= 3 V, RL= 30 , COUT= 1 F, CNR = 0.01 F +
28、25C All 600 typical s Enable high (enabled) VEN(HI) -55C to +125C All 1.7 VINV Enable low (shutdown) VEN(LO) -55C to +125C All 0 0.5 V Enable pin current (enabled) IEN(HI) VEN= 5.5 V -55C to +125C All 0.1 A Thermal shutdown temperature TSDShutdown, temperature increasing +25C All 160 typical C Reset
29、, temperature decreasing 140 typical Operating ambient temperature TAAll -55 +125 C 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temper
30、ature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ Unless otherwise specified, VIN= VOUT(nom) + 0.5 V, IOUT= 10 mA, VEN= 1.7 V, and COUT= 0.1 F. 3/ Minimum VIN= VOUT+ VDOor
31、1.7 V, whichever is greater. 4/ Device type 01 is tested at VOUT= 2.5 V. 5/ VDOis not measured for device type 02 or device type 03, since minimum VIN= 1.7 V. 6/ Fixed voltage versions only; see the vendors datasheet applications section for more information. Provided by IHSNot for ResaleNo reproduc
32、tion or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06644 REV A PAGE 7 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE
33、 SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06644 REV A PAGE 8 Case X Dimensions Symbol Inch Millimeters Min Max Min Max A - .057 - 1.45 A1 .000 .006 0.00 0.15 b .011 .019 0.30 0.50 c .003 .008 0.08 0.22 D .108 .120 2.75 3.05 E .057 .068 1.45 1.75 E1 .102 .118 2.6
34、0 3.00 e .037 BSC 0.95 BSC L .011 .021 0.30 0.55 L1 .009 BSC 0.25 BSC n 5 leads 5 leads NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed 0.15 mm (0.006
35、 inch) per side. 3. Falls with JEDEC MO-178-AA. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06644 REV A PAGE 9 Device types A
36、ll Case outline X Terminal number Terminal symbol Description 1 IN Unregulated input supply. 2 GND Ground. 3 EN Driving the enable pin (EN) high turns on the regulator. Driving this pin low puts the regulator into shutdown mode. See the vendors datasheet shutdown section under application informatio
37、n for more details. EN can be connected to IN if not used. 4 NR Fixed voltage versions only, connecting an external capacitor to this pin bypasses noise generated by the internal bandgap, reducing output noise to very low levels. 4 FB Adjustable voltage version only, this is the input to the control
38、 loop error amplifier, and is used to set the output voltage of the device. 5 OUT Output of the regulator. There are no output capacitor requirements for stability. FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFEN
39、SE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06644 REV A PAGE 10 Fixed voltage FIGURE 3. Block diagrams. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE I
40、DENT NO. 16236 DWG NO. V62/06644 REV A PAGE 11 Adjustable voltage Standard 1 % resistor values for common output voltages VOUTR1R21.2 V Short Open 1.5 V 23.2 k 95.3 k 1.8 V 28.0 k 56.2 k 2.5 V 39.2 k 36.5 k 2.8 V 44.2 k 33.2 k 3.0 V 46.4 k 30.9 k 3.3 V 52.3 k 30.1 k 5.0 V 78.7 k 24.9 k NOTE: VOUT= (
41、R1+ R2) / R2x 1.204; R1| R2 19 k for best accuracy. FIGURE 3. Block diagrams - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 16236 DWG NO. V62/06644 REV A PAGE 12 4. VE
42、RIFICATION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling
43、of moisture sensitive devices, as applicable. 5. PREPARATION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturers standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrosta
44、tic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturers data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modi
45、fied as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DLA Land and Maritime maintains an online database of all current
46、 sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Vendor item drawing administrative control number 1/ Device manufacturer CAGE code Vendor part number 2/ V62/06644-01XE 01295 TPS73201MDBVREP V62/06644-02XE 01295 TPS73215MDBVREP V62/06644-03XE 01295 TPS73216MDBVREP V62/06644-04
47、XE 01295 TPS73218MDBVREP V62/06644-05XE 01295 TPS73225MDBVREP V62/06644-06XE 01295 TPS73230MDBVREP V62/06644-07XE 01295 TPS73233MDBVREP V62/06644-08XE 01295 TPS73250MDBVREP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. 2/ Output voltages from 1.2 V to 4.5 V in 50 mV increments are available through the use of innovative factory EEPROM programming; minimum order quantities may apply. Contact factory for details and availability, www
