1、FF-S-88B June 29, 1977 SUPERSEDING FF- S- 88A June 24, 1966 FEDERAL SPECIFICATION SCREW, EYE This specification was approved by the Commissioner, Federal Supply Service, General Services Administration, for the use of all Federal agencies. 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification co
2、vers a fastening device with one end formed in the shape of an eye and the other end threaded with a wood screw type of thread. 1.2 Classification. * 1.2.1 Classes and grades. Screw eyes covered by this specification shall be of the following classes and grades as specified (see 6.1) : Class 1 - Lar
3、ge eye, regular shank Class 2 - Medium eye, regular shank Class 3 - Small eye, regular shank Class 4 - Small eye, short shank Grade A - Steel Grade B - Copper alloy 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issue in effect on dae of invitation for bids or request for proposel, form
4、 a part of the specifi- cation to the extent specified herein. - Federal. Specifications : QQ-P-416 - Plating, Cadmium (Electrodeposited) QQ-11-321 - Wire Copper Alloy QQ- z- 325 - Zinc Coating, Electrodeposited, Requirements for PPP-H-1581 - Hardware (Fasteners and Related, Items ) Pack- aging and
5、Packing for Shipment and Storage of THIS DOCUHENT CONTAINS 7 PAGES. II-_ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF- S- 88B Federal Standards: Fed. Std. No. 66 - Steel: Chemical Composition and Hardenability (Activities outside the Federal Go
6、vernment may obtain copies of Federal Specifications and Standards as outlined under General Information in the Index of Federal Specifications and Standards and at theaprices indicated The Index, which includes cumulative monthly supplements as issued, is for sale on a subscription basis by the Sup
7、erintendent of Documents, U. S. Government Printing Office, Washington, DC (Single copies of this specification and other Federal specifications required by activities outside the Federal Government for bidding purposes are available without charge at the General Services Administration regional Off
8、ices in Boston, New York, Washington, DC, Atlanta, Chicago, Kansas City, Mo., Dallas, Denver, San Francisco, Los Angeles and Seattle, WA. (Federal Government activities may obtain copies of Federal Specifications and Standards and the Index of Federal specifications and Standards frcan established d
9、istribution points in their agencies ) . ,in the Index. 20402. Military Specifications : MIL-F-495 - Finish, Chemical, Black, for Copper Alloys Military Standards MIL-STD-105 - Sampling Procedures and Tables for Inspection by Attributes (Copies of Military Specifications and Standards required by su
10、ppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer. ) 3. REQUIREMENTS 3.1 Materials. . 3.1.1 Carbon steel. Steel screw eyes shall be made of carbon steel wire conforming to AIS1 No. i013 through 1022 of F
11、ed. Std. No. 66. 3.1.2 Copper alloy. Copper alloy screw eyes shall be made of brass wire conforming to either composition 260 or 270, half hard temper, of QQ-W-321 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF- S- 88B 3.2 Design and dimensions.
12、3.2.1 Design. Design of screw eyes shall conform to figure 1. The eye shall be virtually free fran any opening at the shank. method of forming involves spring-back, an opening of 10 percent of the wire diameter will be permitted at the juncture of the eye with the shank. When the A FIGURE 1 3.2.2 Po
13、int. Screw eyes shall have a grimlet point. 3.2.3 Threads. The shank shall have a wood screw type thread. The number of threads pr inch shall be in accordance with commercial practice. 3.2.4 Dimensions. Dimensions of screw eyes shall conform to Table I. All dimensions are in inches (see 6.1). 3.3 Pr
14、otective finishi. Unless otherwise specified (see 6.11, screw eyes shall be furnished uncoated. When cadmium, zinc, or black oxide coatings are specified, they shall conform to the following paragraphs ( see 6. i). 3.3.1 Cadmium plating. Cadmium plating shall conform to type II, class 3 of QQ-P-416.
15、 3.3.2 Zinc, electrodeposited. Electrodeposited zinc coating shall conform to type II, class 3 of QQ-Z-325. 1.3.3 Black chemical finish. Black chemical finish shall conform to MIL-F-495. 3.4 Workmanship. Screw eyes shall be free from rust, burrs, fins, and sharp edges. 3 Provided by IHSNot for Resal
16、eNo reproduction or networking permitted without license from IHS-,-,-FF-S-BBB 53 7777qr(11 00011000 3 - FF-S-88B TABLE I. Dimensions Wire diameter Elye, inside Shank Thread Length and gage No.1 diameter length length dvera 11 A - -I- 0.005 o00 0.362 O 306 2 .262 4 .225 6 .i9 8 .i62 9 .i48 LO .i34 1
17、2 . i05 i4 .o80 4 0.225 6 .i9 8 ,162 12 105 10 . i34 i4 ,080 4 0.225 6 ,192 8 .i62 12 .1.05 16 ,062 i4 0.080 16 .o62 10 .134 i4 ,080 B 2 0.03 c - + 0.06 D - + 0.12 Class 1, large eye, regular shank 1.12 2 .o6 1.75 0.81 1.56 1.19 72 1.31 1.06 61 1.12 O. 88 53 0.97 75 47 . ai .62 .44 75 56 41 69 53 38
18、 58 44 34 50 31 Class 2, medium eye, regular shank 0.48- 1.12 0.88 .44 97 75 9 39 .81 62 9 31 69 0 53 .2a 58 44 25 50 31 Class 3, small eye, regular shank 0.30 1.12 0.88 9 27 97 75 -23 .81 .62 .22 69 53 19 58 .44 .16 50 31 .i4 .44 31 Class 4, small eye, short shank 0.16 0.38 0.22 i4 .22 19 E 2 0.12
19、3.88 2.94 2.62 1.62 1.56 1.38 1.19 1.06 2.06 1.81 1.56 1.31 1.12 94 2.25 1.94 1.94 1.62 1.38 1.19 9 94 .81 69 o .69 50 lDimensions are Amergan Wire Gage Standard. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FF-S-BBB 53 7777774 0004001 5 FF- S-
20、88B 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the supplier is responsible for the per- formance of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the suppl
21、ier may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessa
22、ry to assure that supplies and services conform to prescribed requirements. 4.1.1 Inspection lot. All screw eyes of the same class, material, and protective finish offered.for delivery at any one time shall be considered a lot for purposes of inspectin. 4.2 Sampling. 4.2.1 Sampling for visual and di
23、mensional examination. A random - - sample of screw eyes shall be taken from each lot in accordance with MIL- STD-105, inspection level. S4. be in accordance with table II herein. dividual defect, not to a group of defects. The acceptable quality level (AQL) shall The AQL shall apply to each in- 4.2
24、.2 Sampling for protective finish - test. Sampling for tests of protective finishes shall be in accordance with the applicable specifi- cations referenced in 3.3.1thru 3.3.3. 4.2.3 Sampling for packaging. Sampling for packaging shall be in accordance with PPP-H-1581. 4.3 Examination. 4.3.1 Visual an
25、d dimensional. Screw eyes taken as specified in 4.2.1 shall be examined to verify conformance with this specification. Examination shall be conducted in accordance with table II. 4.3.2 Protective finish test. Test of protective finishes shall be conducted in accordance with the applicable specificat
26、ion referenced in 3.3.1 thru 3.3.3. 4.3.3 Packaging. Examination and tests of packaging shall be in accordance with PPP-H-1581. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-m-S-88B TABLE II. Classification of Defects Categories - Defects Inspect
27、ion Method Cri ti cal : Major : 101 l 103 Minor : 201 2cQ 203 204 None defined AQ,L = 4.0 percent we, inside diameter Wire diameter Protective.finish, if required, missing, or of wrong type (see 4.3.2 for test) AQL = 6.5 percent Shank length Thread length Overall length Workman ship SIE* SIE SIE SIE
28、 SIE SIE Vi sua1 * Standard inspection equipment. 5. PREPARATION FOR DELIVERY 5.1 Packaging, packing, and marking. The packaging, packing and marking shall be in accordance with PPP-58. shall be A or C, the level of packing shall be A, B, or C, and the mark- ing shall be civil or military as specifi
29、ed (see 6.1). The level of packaging 6. NOTES 6.1 Ordering data. Purchasers should select the preferred options permitted herein and include the folluwing information in procurement documents. a. b. c. d. e. Title, number, and date of this specification. Class 3.2.4). Protective finish, when require
30、d (see 3.3.1, 3.3.2 and 3.3.3). Level of packaging and packing required (see 5 .i). Whether civil or military marking is required (see 5.1). grade, and wire diameter of screw eye (see 1.2.1 and 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-U.S. G
31、OVERNMENT PRINTING OFFICE : 1977 - 241-233/1123 Orders for this publication are to be placed with General Services Ad- ministration, acting as an agent for the Superintendent of Documents. See section 2 of this specification to obtain extra copies and other documents referenced herein. Price 30 cents each. 7 3 ,. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
