1、I INCH-POUND I 30 March 1992 MIL-C-31002(CG) MILITARY SPECIFICATION CAP, GARRISON, MANS (COAST GUARD) This specification is approved for use by the Unites States Coast Guard, Department of Transportation, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE
2、 1.1 Scope. This specification covers the requirements for lined and unlined garrison caps. 1.2 Classification. The caps shall be procured in the following types, classes and sizes as specified (see 6.2): 1.2.1 Tvpes and classes. Type 1 - Lined, Polyester/Wool Serge, Blue 3362# -Class 1 - Artificial
3、 Leatherband Class 2 - Terrycloth Sweatband Type II - Unlined, Polyester/Cotton Twill, Blue 3362 Beneficial comments (recommendations; additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Te
4、xtiles Directorate, ATTN: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the self-addressed Standardization Document Improvement Proposal (DD Fsrm 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8405 DISTRIBUT-ION STATEMENT A. Approved for public rele
5、ase; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-C-31002 4 m 99999Ob 0529245 b m 1.2.2 Sizes. 2. APPLICABLE DOCUMENT 2.1 Government documents 2.1.1 Specifications, standards, and handbooks. The following specifica
6、tions, standards, and handbooks form a part of this document to the extent specified herein, Unless otherwise the issue of the Department of Defense Index of Specifications and specified, the issues of these documents shall be those listed in Standards (DODISS) and supplement thereto, cited in the s
7、olicitation (see 6.2). i ;r; SPECIFICATIONS FEDERAL A-A-50 19 9 - Thread, Polyester Core, Cotton - or Polyester-Covered A-A-5 20 94 - Thread, Cotton NN-P-71 - Pallet, Material Handling, Wood, Stringer Construction 2 Way and 4 Way (Partial) DDD-L-20 - Label; for Clothing, Equipage, and Tentage (Gener
8、al Use) . MILITARY MIL-C-36 8 MIL-C-823 MIL-P-15011 - MIL-B-17757 - MIL-C-29127 - MIL-S-43993 - MIL-C-44121 - Cloth, Satin, Rayon and Cloth, Twill, Rayon Clokh, Serge; Wool, Wool arid Nylon, Pallet, Material Handling, Wood, Post Boxes., Shipping, Fiberboard (Modular Cloth, Twill, Polyester/Cotton (C
9、rease- Sweatband, Headwear, Artificial Leather Cloth, Twilli Polyester Polyester and Wool Construction, 4 Way Entry Sizes) Resistant Finish) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitch
10、ings MILITARY MIL-STD-105 - Sampling Procedures and Tables for MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-901 - Provisions for Evaluating Quality of Caps, MIL-STD-2073-1 - DOD Materials Procedures for Development MIL-STD-2073-2 - Packaging Requirement
11、Codes Inspection by Attributes Garrison, Mens and Applications of Packaging Requirements (Unless otherwise indicated, copies of -federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 1
12、9111-5094). 2.1.2 Other Government documents, drawinqs, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein, Unless otherwise specified, the issues are those cited in the solicitation. US POSTAL MANUAL (Co
13、pies of the manual may be obtained from the SuDerintendent of Documents, US Government Printing Office, Washington, DC 20402- 0001). 2.2 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the doc
14、uments which are DOD adopted shall be those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issue of the documents cited in the solicitation (see 6.2). 3 Provided by IHSNot for ResaleNo reproduction or
15、networking permitted without license from IHS-,-,-MIL-C-3L002 84 9999906 0529247 T t NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applications for copies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Stree
16、t, N.W., Washington, DC 20036-1404). UNIFORM CLASSIFICATION COMMITTEE, AGENT .Uniform Freight Classification (Applications for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808). THE COLOR ASSOCIATION OF THE UNITED
17、STATES Department of Defense Standard Shades for Sewing Threads Association of the United States, 409 W. 44th Street, New York, NY (Applications for copies shall be addressed to the Color 10016-0927). (Non-Government standards and other publications are normally available from the organizations that
18、 prepare or distribute the documents. These documents may also be available in or through libraries or other informational services). 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Not
19、hing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in t
20、he sample in which case this specification shall govern. 3.2 First article. When specified (see 6.2), the contractor shall furnish sample units for first article inspection and approval, in accordance with 4.3, 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr
21、om IHS-,-,-MIL-C-3L002 84 = 9999906 0529248 I W 3,3 Material, 3.3.1 Basic material. 3.3.1,l Cloth, polyester/wool. The basic cloth for the Type I, cap- shall be a polyester/wool serge conforming to ML-C-823. The cloth shall be dyed to match Blue Shade 3362. The standard sample piece number is 80353.
22、 3.3.1.2 Basic cloth, twill, polyester/cotton. The basic cloth for the Type II cap shall be a polyester/cotton twill cloth conforming to MIL-C-29127. The cloth shall be dyed to match Blue Shade 3362. The standard sample piece number is -78349. 3.3.1.3 Cloth, linins. The cloth forlining the Type I ca
23、p shall be a rayon twill cloth conforming to Class 1 of MIL-C-368. As an alternate, the lining material may be a polyester twill conforming to MIL-C-44121. The cloth shall be dyed to approximate the shade of the cap. 3.3.2 Sweatband. * 3.3.2.1 Sweatband, artificial leather. The sweatband for the Typ
24、e I, class 1 caps shall be made from artificial leather , conforming to MIL-S-43993 dyed black to finish not less than 7/8 inch in width. 3.3.2.2 Sweatband, terrycloth. The sweatband for the Type I, class 2 caps shall be made from three layers of material. The outer layer shall be made from a black
25、1-3/4 inch wide 75/25 cotton/polyester knitted terrycloth weighing a minimum of 10.0 oz/sq yd. The middle layer shall be a 0.090 inch thick, 1-1/4 inch wide charcoal grey klicker foam. The inner layer shall be a black 1-1/4 inch wide spunbonded nonwoven. The finished sweatband shall have good colorf
26、astness to perspiration and dry cleaning and shall be 1-1/4 (+/- 1/16) inches wide, 3.3.2.3 Sweatband, cloth. The cloth sweatband for the Type II cap shall be made of the material specified in 3.3.1.2, cut 2-1/8 inches in width, unfinished. 5 Provided by IHSNot for ResaleNo reproduction or networkin
27、g permitted without license from IHS-,-,-MIL-C-31002 84 9999906 0529249 3 W MIL-C-31002(CG) 3.3.4 Thread. The thread for seaming and stitching the caps shall be cotton-covered or polyester-covered thread conforming to 2 ply, ticket No. 50 or 70 of A-A-50199. As an alternate, the thread for seaming a
28、nd stitching the caps shall be cotton thread conforming to Type III, Ticket Nos. A, and B, 3-ply of A-A-52094. The thread for Type I and II caps shall be dyed to match shade Navy Blue AT, Cable No. 66060, in accordance with the Department of Defense Standard Shades for Sewing Threads, except that th
29、e thread used for the stitching the sweatband of the Type I cap shall approximate the shade of the sweatband. 3.3.4.1 Colorfastness. The dyed thread shall show fastness to light, laundering, wet-dry cleaning, and perspiration equal to or better than the standard sample when tested as specified in A-
30、A-52094 or A-A-50199, As a limit of acceptability, or when a standard sample is not available, the dyed thread shall show a minimum of “good“ fastness to light, laundering, wet-dry cleaning, and perspiration, when tested as specified in A-A-52094 or A-A-50199. 3.3.5 Labels. Each cap shall have a com
31、bination identification, size, and personal label and a separate instruction label in accordance with 3.3.5.1 and 3.3.5.2. 3.3.5.1 Combination label. Each cap shall have an identification, size and personal label conforming to Type VI, classes 4 and 10, of DDD-L-20, except that the inscription shall
32、 be as shown below. The size of the label shall be not more than 1-1/2 inches in height and 2-1/2 inches in length. The height of the lettering except for the applicable size shall be 1/16 to 1/8 inch. The size lettering shall be not less than 1/4 inch. The label shall show fastness to drycleaning o
33、nly when Type I caps are applicable and to laundering only when Type II caps are applicable. NAME : SERVICE NO.: CAP, GARRISON, MANS (65% POLYESTER/35% COTTON) (EXAMPLE) CONTRACT NO,! DLA-100-00-0-000 (EXAMPLE) STOCK NO.: 8405-00-000-0000 (EXAMPLE) NAME OF CONTRACTOR: SIZE: 6 Provided by IHSNot for
34、ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-31002 BV m 9999906 0529250 T m 3.3.5.2 Instruction label. Each cap shall have an instruction label conforming to Type VI, Class 3 of DDD-L-20. The size of the label shall be not more than 1-1/2 inches in height and 2-1/
35、2 inches in length. The size of the lettering shall be 1/16 to 1/8 . inch. The label shall show fastness to drycleaning only when Type 1 caps are applicable and to laundering only when Type II caps are applicable. The inscription for the Type I cap shall be as follows: LAUNDERING INSTRUCTIONS DRY CL
36、EAN ONLY The inscription for the Type II cap shall be as follows: LAUNDERING INSTRUCTIONS MACHINE WASH WARM, PERMANENT PRESS CYCLE TUMBLE DRY, MEDIUM SETTING REMOVE PROMPTLY DO NOT USE CHLORINE BLEACH 3.4 Desiqn. The cap shall be a garrison style, having a three piece crown and a one piece curtain t
37、urned up on the outside of the cap with the tapered ends crossing at the front. The caps shall be lined or unlined and shall have an artificial leather, terrycloth or basic cloth sweatband, as specified. 3.4.1 Fiqures. Figures 1 and 2 are furnished for information purposes only. When inconsistencies
38、 exist between the written specification and the figures, the written specification shall govern. 3.5 Patterns. Standard patterns to be used to cut the working patterns will be furnished by the Government (see 6.3). The working patterns shall be identical to the Government patterns. Neither the Gove
39、rnment patterns nor the working patterns shall be altered in any way, except that additional notches for use during construction are permitted on the working patterns, Also, minor modifications are .permitted where necessary when using automatic equipment. These modifications shall not alter the dim
40、ensional, serviceability, or appearance requirements cited in the specification. Standard patterns shall show size, directional lines, placement marks, and notches for assembly. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-33002 84 W 99999
41、06 0529253 3 3.5.1 List of pattern parts. The caps shall be cut from material as specified, and in accordance with pattern parts indicated below: TABLE I - List of Pattern Parts Ma teria 1 Basic material Cloth, lining Nomenclature Cut parts Side crown 2 Top crown (gusset) 1 Curtain 1 Side crown lini
42、ng 2 (Type 1 only) 3.6 Construction, 3.6.1 Stitches, seams, and stitchinqs. Stitch, seams, and stitching types, asspecified in Table II shall conform to the requirements of FED-STD-751. Whenever two or more methods for seams or stitchings are given for the same operation, any one of them may be used
43、. Seam allowances shall be maintained with seams sewn so that no raw edges, runoffs, twists, pleats, puckers, or open seams result. All seams shall start and finish evenly. Thread tension shall be maintained so that there is no tight or loose stitching. Where stitch type 401 is used, the looper (und
44、erthread) shall be on the inside of the cap. Ends of all seams produced by stitch type 401 shall be caught in other seams or stitchings. The width of the safety stitch shall be 3/8 inch and the guides and knives on the saety stitch machine shall be set to trim only the ravelled ends of the fabric. 3
45、.6.2 Stitches per inch. The minimum and maximum number of stitches per inch shall be as specified in Table II. 3.6.3 Thread breaks and ends of seams. Ends of all seams and stitchings, when not caught in other seams or stitchings, shall be backtacked not less than 3/8 inch. The ends of a continuous l
46、ine of stitching shall be overlapped not less than 1/2 inch. For Type I only, the ends of the label stitching shall be overlapped not less than 3 stitches. Thread breaks (all stitch types) shall be secured by stitching back of break not less than 1/2 inch. Skipped stitches or thread breaks of 401 st
47、itching shall be repaired by using 301 stitch type. When the ends of overedge stitching are not caught in other stitching or seams, the ends shall be tacked. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-31002 4 9999906 0529252 3 M 3.7 Manu
48、facturinq operations requirements. The caps shall be The contractor is not required to follow manufactured in accordance with the operation requirements specified in Table II. the exact sequence of operations listed, provided that the finished cap is identical to that produced by following the seque
49、nce of operations as listed in Table II. Minor modifications are permitted where necessary when using automatic equipment. These modifications shall not alter the appearance, serviceability, or dimensional requirements cited in the specification. 3.7.1 Shade-and size markinq. The component parts shall be marked or ticketed to insure a uniform shade and size throughout the cap. Any method may be used except: 1. Meta
