1、 INCH POUND MIL-DTL-12354G 21 December 2000 SUPERSEDING MIL-T-12354F 29 July 1988 DETAILED SPECIFICATION TENT, ARCTIC, 10 MAN This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This document covers a pole-supported six-sided pyram
2、idal tent fabricated of wind-resistant, cotton sateen cloth. A fire-resistant insulting liner and a protective cover for the tent and components are provided with the tent. 2. APPLICABLE DOCUMENTS *2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specificat
3、ion. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements d
4、ocuments cited in sections 3 and 4 of this specification, whether or not they are listed. *2.2 Government documents. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Supply Center Philade
5、lphia, Clothing and Textiles Directorate, Attn: DSCP-CNR, 700 Robbins Avenue, Building 6D, Philadelphia, PA 19111-5094, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8340 Provided by IHSNot for ResaleNo repr
6、oduction or networking permitted without license from IHS-,-,-MIL-DTL-12354G 2 *2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issue of these documents
7、 are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-55126 - Fastener Tapes, Hook and Pile, Synthetic V-F-106 - Fasteners, Slide, Interlocking V-T-285 - Threa
8、d, Polyester TT-P-595 - Preservation Coating, Canvas DDD-L-20 - Label, for Clothing, Equipage and Tentage, (General Use) GGG-N-202 - Needle, Sailmakers MILITARY MIL-C-496 - Clip, End Strap MIL-P-500 - Plates, Tent, Peak and Ridge MIL-P-501 - Pins, Tent, Metal MIL-W-530 - Webbing, Textile, Cotton, Ge
9、neral Purpose, Natural or in Colors MIL-H-1608 - Hooks, Tent MIL-L-1709 - Lines, Tent MIL-DTL-1716 - Poles, Tent, telescopic, Adjustable 5-Feet to 9-Feet, Magnesium MIL-S-1734 - Slips, Tent Line MIL-R-3390 - Rings, Dee MIL-C-3395 - Cloth, Netting; Nylon or Polyester MIL-F-10884 - Fasteners, Snap MIL
10、-L-11075 - Loops, Strap Fastener MIL-C-12095 - Cloth, Wind-Resistant Sateen, Cotton; Fire and Water Resistant MIL-PRF-20696 - Cloth, Coated, Polyester and Nylon, Waterproof MIL-S-43002 - Shield, Stovepipe, Tent, Nonmetallic MIL-C-43256 - Cord, Polyester, Solid Braid MIL-T-43333 - Tent Liner, General
11、 Purpose, Small and Artic, 10-Man MIL-T-43566 - Tape, Textile, Cotton or Polyester, General Purpose, Natural or in Colors MIL-C-43627 - Cloth, Duck, Cotton, Plied Yarns, Fire, Water, Weather and Mildew Resistant Treated, Lightdry Finish MIL-W-43638 - Webbing, Textile, Woven, for Tent Framing MIL-W-4
12、4049 - Webbing, Textile and Tape, Textile, Polypropylene General Purpose, Natural or in Colors Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-12354G 3 *(Unless otherwise indicated, copies of federal and military specifications, standards and
13、 handbooks are available from the Defense Automated Printed Service, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) *2.2.2 Other government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the ext
14、ent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DEPARTMENT OF THE ARMY FIELD MANUAL FM 10-16 - General Repair of Tents, Canvas and Webbing *(Copies of the manual are available from the U. S. Army Biological and Chemical Command, ATTN: SSCNC-EMSS, Nat
15、ick, MA 01760-5017.) DRAWINGS U.S. ARMY BIOLOGICAL AND CHEMICAL COMMAND 4-1-206 - Rings, Connecting, Round 5-4-231 - Cover, Tent; Hexagonal, Lightweight and Arctic, 10-Man 5-4-284 - Tent, Arctic, 10-Man; Illustrations 5-4-285 - Assembly and Details 5-4-286 - Views and Details 5-4-287 - Front and Rea
16、r Details 5-4-288 - Assembled Front, Rear and Details 5-4-289 - Side Details and Sections 5-4-290 - Ventilator and Details 5-4-291 - Screen Door and Details 5-4-544 - Erection Instructions 5-4-545 - Maintenance, Striking and Folding Instructions 5-4-580 - Repair Kit 5-4-1075 - Pole, Telescopic, Adju
17、stable, 5-0” to 9-0”, Magnesium; Details *(Copies of drawings are available from the U.S. Army Biological and Chemical Command, ATTN: SSCNC-EMSS, NATICK, MA 01760-5017.) *2.3 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless ot
18、herwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in this solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). Provided by I
19、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-12354G 4 AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) A47 - Standard Specification for Ferritic Malleable Iron Castings A513 - Standard Specification for Electric-Resistance-Welded Carbon and Alloy Stee
20、l Mechanical Tube A519 - Standard Specification for Seamless Carbon and Alloy Steel Mechanical Tubing A641 - Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire A809 - Standard Specification for Aluminum-Coated (Aluminized) Carbon Steel Wire A818 - Standard Specification for Copper
21、ed Carbon Steel Wire A853 - Standard Specification for Steel Wire, Carbon, for General Use B134 - Standard Specification for Brass Wire B 159 - Standard Specification for Phosphor Bronze Wire B 159M - Standard Specification for Phosphor Bronze Wire (Metric) B 206 - Standard Specification for Copper-
22、Nickel-Zinc Alloy (Nickel Silver) Wire and Copper B206M - Standard Specification for Copper-Nickel-Zinc Alloy (Nickel Silver) Wire and Copper (Metric) D6193 - Seams, Stitching and Sewing *(Copies may be obtained from the American Society for testing and Materials, 100 Barr Harbor Drive, West Conshoh
23、ocken, PA 19428.) NAVAL LOGISTICS LIBRARY (NLL) NASM NATIONAL AEROSPACE STANDARDS COMMITTEE (NA/NAS) NASM 16491 - Grommet, Metallic NASM 43770/10 - Snap, Hooks, Cast Body, Fixed Loop Eye w/o Roller, Flat Spring Closure, Wide Mouth * (Copies may be obtained from the Naval Logistics Library, 5450 Carl
24、isle Pike, Mechanicsburg, PA. (703) 813-8387. AMERICAN NATIONAL STANDARDS INSTITUTE(ANSI) ANSI / ASQC Z1.4-SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES * (Applications for copies should be obtained from: American Society for Quality Control, 611 East Wisconsin Avenue, Milwaukee, WI 53
25、202). *2.4 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification takes precedence. Nothing in this specification, however, supersedes applicable laws and regulations unless a specific exemption has been
26、obtained. 3. REQUIREMENTS *3.1 First article. When specified, (see 6.2), a sample shall be subjected to first article inspection (see 4.2 and 6.2). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-12354G 5 *3.2 Materials and components. Materi
27、als and components shall be as specified herein and in referenced documents and drawings. Materials not definitely specified shall be of the quality normally used by the manufacturer provided the complete item complies with all provisions of this document. It is encouraged that recycled material be
28、used when practical as long as it meets the requirements of this document. *3.2.1 Cloth, wind-resistant sateen, cotton. The cloth for the tent shall be Camouflage Green 483 and shall conform to MIL-C-12095. *3.2.2 Cloth, cotton duck. The cotton duck for the peak reinforcement shall be Camouflage Gre
29、en 483 and shall conform to type I of MIL-C-43627. Requirements for colorfastness to weathering shall not apply. *3.2.2.1 Cloth, coated. The cloth for the tent cover shall conform to type II, class 2 of MIL-PRF-20696 and the color shall be Camouflage Green 483. *3.2.2.2 Fastener tape. The fastener t
30、apes, hook and pile shall conform to type II, class 3, Color 3422 of A-A-55126. 3.2.3 Cloth, netting, nylon. The nylon netting for the ventilator opening and screen door shall conform to type I or II of MIL-C-3395. 3.2.4 Shield, stovepipe, tent. The flexible, silicone rubber coated stovepipe shield
31、shall conform to MIL-S-43002. *3.2.5 Tape, textile, cotton. The tape shall be Camouflage Green 483 and shall conform to type I, class 4, inch, inch, 1-1/2 inch and 2 inch widths (as specified on applicable drawings) of MIL-T-43566. For covers only, polypropylene tape conforming to type I, class 4, i
32、nch width of MIL-W-44049 may be used as an alternate. *3.2.6 Webbing, textile, cotton. The webbing shall be Camouflage Green 483 and shall conform to type IIb, class 4, 1 inch width and type III, class 4, 5/8 inch and 1-1/2 inch widths (as specified on applicable drawings) of MIL-W-530. For covers o
33、nly, polypropylene webbing conforming to type IIb, class 4, 1 inch width of MIL-W-44049 may be used as an alternate. *3.2.7 Webbing, textile, woven, low elongation. The webbing shall be natural, conforming to type I, 1 inch width of MIL-W-43638. 3.2.8 Thread, polyester. The thread for the tent scree
34、ns and cover shall conform to type I, class 1, sub-class B, shade S-1 (C.A. 66022) of V-T-285. The dyed thread shall show fastness to weathering equal to or better than the standard shade sample. When no standard shade sample is available, the thread shall show good fastness to weathering. Provided
35、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-12354G 6 3.2.8.1 Sizes. Thread sizes shall be as follows: For all stitching except zig-zag - Size F for needle and size stitching, bartacking and E for bobbin stitching indicated by “Z” on drawings For z
36、ig-zag stitching and - Size E for needle and bobbin bartacking For stitching indicated by “Z” on drawings - Size F needle, size E for looper. 3.2.9 Lines, tent. The tent lines shall conform to class D of MIL-L-1709 in the following types: Type LII (Intermediate eave line, corner eave line) LIII (Cor
37、ner line) except that the length shall be 20 feet LIV (Door eave line) 3.2.10 Cord, polyester. The cord used for the sock lines, toggle loops and beckets shall be Camouflage Green 483, 1/8 inch diameter cord conforming to MIL-C-43256. 3.2.11 Cord, cotton. The cord for the footstops and drip cap stif
38、fener shall conform to type I, class 3, size No. 7 of A-A-55622. The footstops shall be as shown on Drawing 5-4-285. 3.2.12 Toggles. 3.2.12.1 Toggles, wood. The wood toggles of the design and dimensions shown on Drawing 5-4-288, shall be fabricated from uniformly dried, straight-grained lumber and s
39、hall not contain more than 15 percent moisture when tested as specified in 4.4.1.1. The toggles shall be free from knots, shakes, checks, splits, or splintery surface. Any of the following woods may be used: Hickory Beech Pecan Maple, hard Red or White Oak Birch Rock Elm Ash *3.2.12.2. Toggles, meta
40、l. The metal toggles shall be of the design and dimensions shown on Drawing 5-4-286 and shall be fabricated from brass wire conforming to alloy No. 270, half hard temper of ASTM B134, ASTM B159, ASTM B206. The toggles shall have a black chemical finish. 3.2.13 Slips, tent line. The tent line slips s
41、hall conform to type II of MIL-S-1734. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-12354G 7 3.2.14 Fasteners, slide interlocking. The slide fasteners shall conform to type III, style 1, size H, wire stirrup pulls of V-F-106. Slide fastene
42、r chain shall be fabricated of brass or polyester coil. The slider for the brass chain shall be brass and the slider for the polyester coil shall be die cast zinc alloy. The slide fastener tape shall be dyed to match CG 483 and be water repellent and mildew resistant. (Tapes made of 100 percent poly
43、ester need not be tested for mildew resistance.) The color of the tape after treatment will be considered acceptable. The tape shall show good fastness to weathering. Alternatively, the slide fastener chain shall be polyester continuous monofilament in a ladder or coil type configuration. Color of t
44、he chain shall be CG 483 or natural finish brass and the sliders shall be brass. 3.2.15 Rings, dee. The dee rings shall conform to class 1 or 2, configuration K, 1 inch by inch of MIL-R-3390. *3.2.16 Ring, connecting. The connecting rings shall be of steel wire or cast malleable iron, black enamel,
45、phosphate treated, zinc plate finished, size 2 or 5 in accordance with Drawing 4-1-206. *3.2.16.1 Steel wire. The steel wire shall conform to steel numbers 1006 to 1020 in accordance with ASTM A853, ASTM A818, ASTM A641 or ASTM A809. *3.2.16.2 Steel tube. The steel tube shall be seamless, round in a
46、ccordance with ASTM A513 and ASTM 519. *3.2.16.3 Malleable iron. The malleable iron shall be grade I (35018)-Black, ungalvanized or grade II (32510)-Black, ungalvanized in accordance with ASTM A47. The first three digits of the grade designations indicate the minimum yield strength ( x 100 p.s.i.).
47、The last two digits indicate the minimum elongation (percent in 2 inches). 3.2.17 Plate, peak. The peak plate shall conform to type XVIII of MIL-P-500. *3.2.18 Snaphooks. The snaphooks shall conform to NASM 43770/10. *3.2.19 Grommets, metallic. The grommets shall conform to type III, class 3 of NASM
48、 16491 in the following sizes: No. 1 (for connecting lug becket cord) No. 2 (for footstops, type “B”) No. 4 (for footstops, type “A”) 3.2.20 Fasteners, snap. The snap fasteners shall conform to style 2, finish 2, button 24 line size, size 1 and eyelet size 1 of MIL-F-10884. 3.2.21 Clip, end strap. T
49、he end clips shall conform to type I, class 1 or 2, size 1 inch of MIL-C-496. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-12354G 8 3.2.22 Loops, strap fastener. The strap fastener loops shall conform to type III, style B of MIL-L-11075. 3.2.23 Hooks, tent. The tent hooks used at the peak plate shall conf
