1、 AMSC N/A FSC 5996 MIL-DTL-28875/6B 15 June 2010 SUPERSEDING MIL-DTL-28875/6A 24 August 2000 DETAIL SPECIFICATION SHEET AMPLIFIERS, RADIO-FREQUENCY AND MICROWAVE, SOLID-STATE, LOW NOISE, WIDEBAND, COAXIAL CONFIGURATION This specification is approved for use by all Departments and Agencies of the Dep
2、artment of Defense. The requirements for acquiring the amplifiers described herein shall consist of this specification sheet and MIL-DTL-28875. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3. Barrel diameter shall accept two
3、turns of AWG NO. 24 wire. FIGURE 1. Dimensions and configuration, dash number -01. INCH-POUND Inches Millimeters Max Min Max Min A 1.885 1.865 47.88 47.37 B .202 dia .082 dia 5.13 dia 2.08 dia C .850 .830 21.59 21.08 D .135 .115 3.43 2.92 E 1.880 1.870 47.75 47.50 F 1.630 1.620 41.40 41.15G .947 .92
4、7 24.05 23.55 H 1.635 1.615 41.53 41.02J .135 .115 3.43 2.92 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28875/6B 2 NOTE: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3.
5、Barrel diameter shall accept two turns of AWG NO. 24 wire. FIGURE 2. Dimensions and configuration, dash number -02. Inches Millimeters Max Min Max Min A .27 .23 6.9 5.8 B 1.385 typ 1.365 typ 35.18 typ 34.67 typ C .71 .67 18.0 17.0 D 3.385 3.365 85.98 85.47 E .166 dia .146 dia 4.22 dia 3.71 dia F .21
6、 .17 5.3 4.3 G .90 .86 22.9 21.8 H 1.77 1.73 45.0 43.9 J .42 typ .38 typ 10.7 typ 9.7 typ K .14 .10 3.6 2.5 L .59 .55 15.0 14.0 M 3.02 2.98 76.7 75.7 N 3.77 3.73 95.8 94.7 P 1.02 .98 25.9 24.9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-2
7、8875/6B 3 Inches Millimeters Max Min Max Min K .40 typ - 10.2 typ - L .57 typ - 14.5 typ - NOTES: 1. Dimensions are in inches (see Table II). 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3. Barrel diameter shall accept two turns of AWG NO. 24 wire. FIGURE 3. Di
8、mensions and configuration, dash numbers -03, -04, -07, -08, -10, -11, and -12. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28875/6B 4 Inches Millimeters Max Min Max Min K .75 - 19.1 - L .135 .115 3.43 2.92 NOTES: 1. Dimensions are in inc
9、hes (see Table II). 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3. Barrel diameter shall accept two turns of AWG No. 24 wire. FIGURE 4. Dimensions and configuration, dash numbers -05 and -09. Provided by IHSNot for ResaleNo reproduction or networking permitted
10、 without license from IHS-,-,-MIL-DTL-28875/6B 5 Inches Millimeters Max Min Max Min A .10 .08 2.5 2.0 B 1.126 1.106 28.60 28.09 C .57 - 14.5 - D 1.126 1.106 28.60 28.09 E 1.32 1.28 33.5 32.5F .78 .76 19.8 19.3 G .10 .08 2.5 2.0 H 1.32 1.28 33.5 32.5 J .29 .27 7.4 6.9 K .40 typ - 10.2 typ - L .63 typ
11、 - 16.0 typ - M .127 dia .123 dia 3.23 dia 3.12 dia NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only (1.00 inch = 25.4 mm). 3. Barrel diameter shall accept two turns of AWG No. 24 wire. FIGURE 5. Dimensions and configuration, dash number -06. Provided
12、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE I. Electrical characteristics (25C unless otherwise specified). Dash No. Frequency range DC input power Gain (dB) Gain flatness (dB) RF output power (dBm) VSWR Max Noise figure (dB) Intercept point (dBm) G
13、ain vs temp. (dB) RF input power Isolation (dB) Phase linearity (deg) Voltage Curr. Max (mA) Min Max Min IN OUT Max Min Max Min Max S1 01 S2 N 5-250 MHz +15 1% 15 25 0.5 +5 2.0:1 2.0:1 1.5 +17 0.5 N/A N/A N/A S1 02 S2 N 100-200 MHz +15 1% 30 27 1.0 +5 2.0:1 2.0:1 2.5 +15 N/A N/A N/A N/A S1 03 S2 N 1
14、0-400 MHz +15 1% 40 40 1.5 +6.5 2.5:1 2.5:1 3.5 +19 N/A N/A N/A N/A S1 04 S2 N 10-500 MHz +15 1% 130 38 1.5 +19 2.5:1 2.5:1 4 +34 N/A N/A N/A N/A S1 05 S2 N 5-1000 MHz +15 1% 15 14 1.0 -2 2.0:1 2.0:1 5 N/A N/A N/A N/A N/A S1 06 S2 N 100-2000 MHz +15 1% 23 9 1.0 +5 2.0:1 2.0:1 6.5 +15 N/A N/A N/A N/A
15、 S1 07 S2 N 500-2000 MHz +12 1% 200 36 1.0 +15 2.0:1 2.0:1 3.5 +25 N/A N/A N/A N/A S1 08 S2 N 500-2000 MHz +12 1% 160 27 1.0 +15 2.0:1 2.0:1 3.5 +25 N/A N/A N/A N/A S1 09 S2 N 500-2000 MHz +15 1% 110 25 1.0 +12 2.0:1 2.0:1 4.0 +23 N/A N/A N/A N/A MIL-DTL-28875/6B6 Provided by IHSNot for ResaleNo rep
16、roduction or networking permitted without license from IHS-,-,-TABLE I. Electrical characteristics (25C unless otherwise specified) - Continued. Dash No. Frequency range DC input power Gain (dB) Gain flatness (dB) RF output power (dBm) VSWR Max Noise figure (dB) Intercept point (dBm) Gain vs temp. (
17、dB) RF input power Isolation (dB) Phase linearity (deg) Voltage Curr. Max (mA) Min Max Min IN OUT Max Min Max Min Max S1 10 S2 N 8-12 GHz +12 1% 250 37 2.0 +13 2.0:1 2.0:1 5.5 +23 N/A N/A N/A N/A S1 11 S2 N 8-12 GHz +12 1% 150 22 1.5 +13 2.0:1 2.0:1 5.5 +23 N/A N/A N/A N/A S1 12 S2 N 12-18 GHz +12 1
18、% 375 33 2.0 +10 2.0:1 2.0:1 7.0 +20 N/A N/A N/A N/A MIL-DTL-28875/6B7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TABLE II. Dimensions, physical and environmental characteristics. Dash No. Dimensions (in) Weight (lb) Max Temperature range Seal S
19、alt EMI RF connectors A B C D E F G H J M Operating case temp Nonoper-ating Input Output Fig No. S1 01 S2 N N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A .44 -54/+71C -54/+85C Non- hermetic N/A CE03 MIL-STD-461 Female Female 1 S1 02 S2 N N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A .44 -54/+71C -54/+85C Non- h
20、ermetic N/A CE03 MIL-STD-461 Female Female 2 S1 03 S2 N 1.33 .02 .750 .01 .29 .01 .700 .02 1.03 .02 .11 .01 .810 .01 .555 .02 .352 .02 2-56 UNC- 2B x .15 Dp .28 -54/+85C -54/+100C Non- hermetic Appli-cable CE03 MIL-STD-461 Female Female 3 S1 04 S2 N 2.35 .02 1.774 .01 .29 .01 .700 .02 1.03 .02 .11 .
21、01 .810 .01 .555 .02 .352 .02 2-56 UNC- 2B x .15 Dp .28 -54/+85C -54/+100C Non- hermetic Appli-cable CE03 MIL-STD-461 Female Female 3 S1 05 S2 N 1.37 .02 1.000 .01 .19 .01 .84 .02 1.50 .02 .11 .01 1.281 .01 .90 .02 .49 .02 .125 dia .24 -45/+81C -57/+81C Non- hermetic N/A CE03 MIL-STD-461 Female Fema
22、le 4 S1 06 S2 N N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A .22 -54/+85C -54/+100C Hermetic Appli-cable CE03 MIL-STD-461 Female Female 5 S1 07 S2 N 2.08 .02 1.58 .01 .25 .01 .67 .02 2.15 .02 .20 .01 .75 .01 .78 .02 .31 .02 4-40 UNC-2B x .25 Dp .17 -54/+85C -54/+100C Hermetic N/A CE03 MIL-STD-461 Female
23、Female 3 S1 08 S2 N 2.08 .02 1.58 .01 .25 .01 .67 .02 1.15 .02 .20 .01 .75 .01 .78 .02 .31 .02 4-40 UNC-2B x .25 Dp .17 -54/+85C -54/+100C Hermetic N/A CE03 MIL-STD-461 Female Female 3 MIL-DTL-28875/6B8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
24、-TABLE II. Dimensions, physical and environmental characteristics. Continued Dash No. Dimensions (in) Weight (lb) Max Temperature range Seal Salt EMI RF connectors Fig. No. A B C D E F G H J M Operating case temp Non- operating Input Output S1 09 S2 N 2.85 .02 2.450 .01 .20 .01 .85 .02 1.95 .02 .11
25、.01 1.732 .01 1.12 .02 .49 .02 N/A .77 -54/+85C -54/+100C Hermetic N/A CE03 MIL-STD-461 Female Female 4 S1 10 S2 N 2.25 .02 1.750 .01 .25 .01 .67 .02 1.15 .02 .20 .01 .75 .01 .64 .02 .31 .02 4-40 UNC-2Bx .25 Dp .22 -54/+71C -54/+85C Hermetic N/A CE03 MIL-STD-461 Female Female 3 S1 11 S2 N 1.75 .02 1
26、.250 .01 .25 .01 .67 .02 1.15 .02 .20 .01 .75 .01 .64 .02 .31 .02 4-40 UNC-2Bx .25 Dp .15 -54/+71C -54/+85C Hermetic N/A CE03 MIL-STD-461 Female Female 3 S1 12 S2 N 4.42 .02 4.25 .01 .09 .01 .54 .02 1.26 .02 .09 .01 1.09 .01 .65 .02 .23 .02 2-56 UNC-2Bx .25 Dp .44 -54/+71C -54/+85C Hermetic N/A CE03
27、 MIL-STD-461 Female Female 3 MIL-DTL-28875/6B9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28875/6B 10 REQUIREMENTS: Dimensions and configuration: See figures and table II. Electrical characteristics: See table I. Physical and environment
28、al characteristics: See table II. Part or identifying number (PIN): M28875/6-(dash numbers from tables I and II) Referenced documents. In addition to MIL-DTL-28875, this specification sheet references the following documents: MIL-PRF-39012 MIL-STD-461 The margins of this specification are marked wit
29、h vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on t
30、he entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project number 5996-2010-002) DLA - CC Review activities: Army - AV, MI Navy - MC, OS, SH Air Force - 19, 99 NOTE: The ac
31、tivities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
