1、MIL-DTL-32434/9 23 January 2013 DETAIL SPECIFICATION SHEET HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, CONVOLUTED, PERMANENTLY ATTACHED FITTINGS, HIGH TEMPERATURE, MEDIUM PRESSURE, FLARELESS-TO-FLANGE This specification is approved for use by all Departments and Agencies of the Department of Defense. Th
2、e requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-32434. Hose assembly dimensions for style A: See figure 1. Fitting ends Hose size Dimensions 1 2 A (ref) B ( max) C (max) F (max) M (max) P (max) Straight Straight 8 .310 1.640 .880 1.014
3、1.560 .875 10 .356 1.940 .967 1.158 1.570 1.000 12 .393 1.913 1.122 1.447 1.640 1.250 16 .429 2.298 1.480 1.736 1.750 1.500 20 .393 2.577 1.750 2.328 1.990 1.844 24 .398 2.800 2.150 2.621 2.260 2.125 NOTES: 1. Style A uses class 1 fittings which are made from corrosion resistant steel (CRES). 2. Dim
4、ensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 1. Style A hose assembly di
5、mensions. AMSC N/A FSC 4720 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 2 Hose assembly dimensions for style B: See figure 2. Fitting ends Hose size Dimensions 1 2 A (ref) B (max) C (max) D (max) F (max) N (max) P (max)
6、 R (min) R (max) Straight 45 8 .310 1.640 .880 1.722 1.014 .606 .875 .303 .428 10 .356 1.940 .967 2.037 1.158 .658 1.000 .340 .465 12 .393 1.913 1.122 2.368 1.447 .789 1.250 .433 .558 16 .429 2.298 1.480 2.583 1.736 .929 1.500 .470 .657 20 .393 2.577 1.750 2.946 2.328 1.020 1.844 .534 .721 24 .398 2
7、800 2.150 3.210 2.621 1.186 2.125 .589 .839 NOTES: 1. Style B uses class 1 fittings which are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Dimension “N (max)”is an installation dimen
8、sions and not a design dimension. 5. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 2. Style B hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permit
9、ted without license from IHS-,-,-MIL-DTL-32434/9 3 Hose assembly dimensions for style C: See figure 3. Fitting ends Hose size Dimensions 1 2 A (ref) B (max) C (max) F (max) P (max) S (max) T (max) U (min) U (max) Straight 90 8 .310 1.640 .880 1.014 .875 2.320 1.422 .857 .982 10 .356 1.940 .967 1.158
10、 1.000 2.875 1.499 .861 1.015 12 .393 1.913 1.122 1.447 1.250 3.606 1.807 1.032 1.246 16 .429 2.298 1.480 1.736 1.500 3.981 2.174 1.156 1.434 20 .393 2.577 1.750 2.328 1.844 4.435 2.590 1.344 1.715 24 .398 2.800 2.150 2.621 2.125 5.075 3.103 1.516 2.028 NOTES: 1. Style C uses class 1 fittings which
11、are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Dimension “T (max)”is an installation dimensions and not a design dimension. 5. Assembly length (see PIN) is based on end of MS8000 se
12、ries seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 3. Style C hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 4 Hose assembly dimensions for style D: Se
13、e figure 4. Fitting ends Hose size Dimensions A (ref) C (max) D (max) E (max) F (max) G (min) G (max) N (max) P (max) R (min) R (max) 1 2 45 45 8 .310 .880 1.722 1.426 1.014 .542 .789 .606 .875 .303 .428 10 .356 .967 2.037 1.596 1.158 .631 .877 .658 1.000 .340 .465 12 .393 1.122 2.368 1.739 1.447 .6
14、31 .952 .789 1.250 .433 .558 16 .429 1.480 2.583 1.931 1.736 .741 1.069 .929 1.500 .470 .657 20 .393 1.750 2.946 2.084 2.328 .863 1.196 1.020 1.844 .534 .721 24 .398 2.150 3.210 2.376 2.621 1.012 1.376 1.186 2.125 .589 .839 NOTES: 1. Style D uses class 1 fittings which are made from corrosion resist
15、ant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimensions “E (max)” and “N (max)” are installation dimensions and not design dimensions. 4. Dimension “F” is measured across the corners. 5. Assembly length (see PIN) is based on end of MS8000 series seal to face
16、 of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 4. Style D hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 5 Hose assembly dimensions for style E: See figure 5. Fitti
17、ng ends Hose size Dimensions A (ref) C (max) D (max) E (max) F (max) G (min) G (max) P (max) S (max) T (max) U (min) U (max) 1 2 45 90 8 .310 .880 1.722 1.426 1.014 .542 .789 .875 2.320 1.422 .857 .982 10 .356 .967 2.037 1.596 1.158 .631 .877 1.000 2.875 1.499 .861 1.015 12 .393 1.122 2.368 1.739 1.
18、447 .631 .952 1.250 3.606 1.807 1.032 1.246 16 .429 1.480 2.583 1.931 1.736 .741 1.069 1.500 3.981 2.174 1.156 1.434 20 .393 1.750 2.946 2.084 2.328 .863 1.196 1.844 4.435 2.590 1.344 1.715 24 .398 2.150 3.210 2.376 2.621 1.012 1.376 2.125 5.075 3.103 1.516 2.028 NOTES: 1. Style E uses class 1 fitti
19、ngs which are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimensions “E (max)” and “T (max)” are installation dimensions and not design dimensions. 4. Dimension “F” is measured across the corners. 5. Assembly length (see PIN) is ba
20、sed on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 5. Style E hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 6 Hose assembly dim
21、ensions for style F: See figure 6. Fitting ends Hose size Dimensions A (ref) C (max) F (max) H (max) J (max) K (min) K (max) P (max) S (max) T (max) U (min) U (max) 1 2 90 90 8 .310 .880 1.014 2.495 2.032 1.032 1.282 .875 2.320 1.422 .857 .982 10 .356 .967 1.158 2.955 2.437 1.357 1.607 1.000 2.875 1
22、499 .861 1.015 12 .393 1.122 1.447 3.705 2.795 1.591 1.841 1.250 3.606 1.807 1.032 1.246 16 .429 1.480 1.736 4.100 3.160 1.741 1.991 1.500 3.981 2.174 1.156 1.434 20 .393 1.750 2.328 4.835 3.664 2.021 2.396 1.844 4.435 2.590 1.344 1.715 24 .398 2.150 2.621 5.480 4.251 2.403 2.778 2.125 5.075 3.103
23、1.516 2.028 NOTES: 1. Style F uses class 1 fittings which are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Dimensions “J (max)” and “T (max)” are installation dimensions and not desig
24、n dimensions. 5. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 6. Style F hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
25、from IHS-,-,-MIL-DTL-32434/9 7 Hose assembly dimensions for style G: See figure 7. Fitting ends Hose size Dimensions 1 2 A (ref) C (max) D (max) E (max) F (max) G (min) G (max) M (max) P (max) 45 Straight 8 .310 .880 1.722 1.426 1.014 .542 .789 1.560 .875 10 .356 .967 2.037 1.596 1.158 .631 .877 1.5
26、70 1.000 12 .393 1.122 2.368 1.739 1.447 .631 .952 1.640 1.250 16 .429 1.480 2.583 1.931 1.736 .741 1.069 1.750 1.500 20 .393 1.750 2.946 2.084 2.328 .863 1.196 1.990 1.844 24 .398 2.150 3.210 2.376 2.621 1.012 1.376 2.260 2.125 NOTES: 1. Style G uses class 1 fittings which are made from corrosion r
27、esistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “E (max)” is an installation dimension and not a design dimension. 4. Dimension “F” is measured across the corners. 5. Assembly length (see PIN) is based on end of MS8000 series seal to face of flan
28、ge. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 7. Style G hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 8 Hose assembly dimensions for style H: See figure 8. Fitting ends
29、Hose size Dimensions 1 2 A (ref) C (max) F (max) H (max) J (max) K (min) K (max) M (max) P (max) 90 Straight 8 .310 .880 1.014 2.495 2.032 1.032 1.282 1.560 .875 10 .356 .967 1.158 2.955 2.437 1.357 1.607 1.570 1.000 12 .393 1.122 1.447 3.705 2.795 1.591 1.841 1.640 1.250 16 .429 1.480 1.736 4.100 3
30、160 1.741 1.991 1.750 1.500 20 .393 1.750 2.328 4.835 3.664 2.021 2.396 1.990 1.844 24 .398 2.150 2.621 5.480 4.251 2.403 2.778 2.260 2.125 NOTES: 1. Style H uses class 1 fittings which are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end of MS8000 series seal.
31、 3. Dimension “F” is measured across the corners. 4. Dimension “J (max)” is an installation dimension and not a design dimension. 5. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 8. Sty
32、le H hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 9 Hose assembly dimensions for style J: See figure 9. Fitting ends Hose size Dimensions A (ref) C (max) D (max) F (max) H (max) J (max) K (min) K (max) N (
33、max) P (max) R (min) R (max) 1 2 90 45 8 .310 .880 1.722 1.014 2.495 2.032 1.032 1.282 .606 .875 .303 .428 10 .356 .967 2.037 1.158 2.955 2.437 1.357 1.607 .658 1.000 .340 .465 12 .393 1.122 2.368 1.447 3.705 2.795 1.591 1.841 .789 1.250 .433 .558 16 .429 1.480 2.583 1.736 4.100 3.160 1.741 1.991 .9
34、29 1.500 .470 .657 20 .393 1.750 2.946 2.328 4.835 3.664 2.021 2.396 1.020 1.844 .534 .721 24 .398 2.150 3.210 2.621 5.480 4.251 2.403 2.778 1.186 2.125 .589 .839 NOTES: 1. Style J uses class 1 fittings which are made from corrosion resistant steel (CRES). 2. Dimensions “A” and “B” are based on end
35、of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Dimensions “J (max)” and “N (max)” are installation dimensions and not design dimensions 5. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/
36、1, see requirements. FIGURE 9. Style J hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 10 Hose assembly dimensions for style K: See figure 10. Fitting ends Hose size Dimensions 1 2 A (ref) B ( max) C (max) F
37、max) M (max) P (max) Straight Straight 8 .310 1.640 .880 1.014 1.560 .875 10 .356 1.940 .967 1.158 1.570 1.000 12 .393 1.913 1.122 1.447 1.640 1.250 16 .429 2.298 1.480 1.736 1.750 1.500 20 .393 2.577 1.750 2.328 1.990 1.844 24 .398 2.800 2.150 2.621 2.260 2.125 NOTES: 1. Style K uses class 2 fitti
38、ngs which are made from a combination of aluminum and CRES. 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5. Apply NAS1760 in accordance with MIL
39、DTL-25579/1, see requirements. FIGURE 10. Style K hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 11 Hose assembly dimensions for style M: See figure 11. Fitting ends Hose size Dimensions 1 2 A (ref) B (max)
40、 C (max) D (max) F (max) N (max) P (max) R (min) R (max) Straight 45 8 .310 1.640 .880 1.722 1.014 .606 .875 .303 .428 10 .356 1.940 .967 2.037 1.158 .658 1.000 .340 .465 12 .393 1.913 1.122 2.368 1.447 .789 1.250 .433 .558 16 .429 2.298 1.480 2.583 1.736 .929 1.500 .470 .657 20 .393 2.577 1.750 2.9
41、46 2.328 1.020 1.844 .534 .721 24 .398 2.800 2.150 3.210 2.621 1.186 2.125 .589 .839 NOTES: 1. Style M uses class 2 fittings which are made from a combination of aluminum and CRES. 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. D
42、imension “N (max)”is an installation dimensions and not a design dimension. 4. Assembly length (see PIN) is based on end of MS8000 series seal to face of flange. 5. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 11. Style M hose assembly dimensions. Provided by IHSNot for
43、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32434/9 12 Hose assembly dimensions for style N: See figure 12. Fitting ends Hose size Dimensions 1 2 A (ref) B (max) C (max) F (max) P (max) S (max) T (max) U (min) U (max) Straight 90 8 .310 1.640 .880 1.014 .875 2
44、320 1.422 .857 .982 10 .356 1.940 .967 1.158 1.000 2.875 1.499 .861 1.015 12 .393 1.913 1.122 1.447 1.250 3.606 1.807 1.032 1.246 16 .429 2.298 1.480 1.736 1.500 3.981 2.174 1.156 1.434 20 .393 2.577 1.750 2.328 1.844 4.435 2.590 1.344 1.715 24 .398 2.800 2.150 2.621 2.125 5.075 3.103 1.516 2.028 N
45、OTES: 1. Style N uses class 2 fittings which are made from a combination of aluminum and CRES. 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimension “F” is measured across the corners. 4. Dimension “T (max)” is an installation dimension and not a design dimension. 5. Assembl
46、y length (see PIN) is based on end of MS8000 series seal to face of flange. 6. Apply NAS1760 in accordance with MIL-DTL-25579/1, see requirements. FIGURE 12. Style N hose assembly dimensions. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32
47、434/9 13 Hose assembly dimensions for style P: See figure 13. Fitting ends Hose size Dimensions A (ref) C (max) D (max) E (max) F (max) G (min) G (max) N (max) P (max) R (min) R (max) 1 2 45 45 8 .310 .880 1.722 1.426 1.014 .542 .789 .606 .875 .303 .428 10 .356 .967 2.037 1.596 1.158 .631 .877 .658
48、1.000 .340 .465 12 .393 1.122 2.368 1.739 1.447 .631 .952 .789 1.250 .433 .558 16 .429 1.480 2.583 1.931 1.736 .741 1.069 0.929 1.500 .470 .657 20 .393 1.750 2.946 2.084 2.328 .863 1.196 1.020 1.844 .534 .721 24 .398 2.150 3.210 2.376 2.621 1.012 1.376 1.186 2.125 .589 .839 NOTES: 1. Style P uses class 2 fittings which are made from a combination of aluminum and CRES. 2. Dimensions “A” and “B” are based on end of MS8000 series seal. 3. Dimensions “E (max)” and “N (max)” are installation dimensions and not design dimensions. 4. Di
