1、 INCH-POUND MIL-DTL-52525/38B 1 December 2008 SUPERSEDING MIL-DTL-52525/38A 30 June 1998 DETAIL SPECIFICATION SHEET FITTINGS, HOSE, SCREW-ON TO 37 FLARE FEMALE SWIVEL, 45 BENT TUBE This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements f
2、or acquiring the product described herein shall consist of this specification sheet and MIL-DTL-52525. FIGURE 1. Fitting, screw-on to 37 flare female swivel, 45 bent tube. AMSC N/A FSC 4730Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-52525
3、/38B 2 Part or Identifying Number (PIN) Hose ID inches (mm) Hose OD inches (mm) Tube OD inches (mm) Thread size (see note 3) C max inches (cm) M52525/38-08-08 .50 (12.70) .94 (23.88) .50 (12.70) .750-16-UNF 4.00 (101.60) M52525/38-12-12 .75 (19.05) 1.21 (30.73) .75 (19.05) 1.063-12-UNC 5.00 (127.00)
4、 M52525/38-16-16 1.00 (25.40) 1.50 (38.10) 1.00 (25.40) 1.313-12-UNC 6.10 (154.94) PIN F max inches (mm) H Hex size inches (mm) L max inches (mm) M min inches (mm) N inches (mm) .030 (0.76) .015 (0.38) M52525/38-08-08 1.00 (25.40) .88 (22.35) 1.29 (32.77) .384 (9.75) .435 (11.05)M52525/38-12-12 1.20
5、 (30.48) 1.25 (31.75) 1.73 (43.94) .487 (12.37) .562 (14.27)M52525/38-16-16 1.55 (39.37) 1.50 (38.10) 2.02 (51.31) .505 (12.83) .594 (15.09)PIN P (see note 3) inches (mm) .005 (0.13) Q Bore dia. min inches (mm) M52525/38-08-08 .570 (14.48) .37 (9.40) M52525/38-12-12 .850 (21.59) .56 (14.22)M52525/38
6、-16-16 1.103 (28.02) .81 (20.57)NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Threads shall be in accordance with ASME B1.1 series with graded pitches fine (UNF) and series with constant pitches (UNC), class 2B. 4. Dimension P to be concentric with dime
7、nsion Q within .015 inch (0.38 mm) full indicator movement. 5. These fittings are for use with MIL-DTL-52471/9 hose and MIL-DTL-52471/10 hose assemblies. FIGURE 1. Fitting, screw-on to 37 flare female swivel, 45 bent tube - Continued. REQUIREMENTS: The fittings described herein are for use with hose
8、 in accordance with MIL-DTL-52471/9, type 100R12, 4-spiral-wrap reinforcement hose and hose assemblies in accordance with MIL-DTL-52471/10. The fittings shall be as specified on figure 1 and in tables I, II, and III. If fittings are to be used on an oxygen hose see MIL-DTL-52525. Materials and finis
9、hes shall be in accordance with MIL-DTL-52525 and in table I. All finishes shall be capable of withstanding 96 hours minimum of salt spray. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-52525/38B 3 TABLE I. Material and finish identificatio
10、n codes. 1/ 2/ PIN code material/plating finish Material Plating finish A Anodize in accordance with MIL-A-8625, type II. AN Anodize in accordance with MIL-A-8625, type II and NAVAIR trivalent chromium pretreatment (TCP) in accordance with MIL-DTL-81706, type 2, class A. BN Aluminum alloy 6061 or 70
11、75 Bare aluminum with NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. C Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2. CN Steel Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II
12、, class 2 and NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. YC Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE-AMS-QQ-P-416, type II, class 2. YN Chrome-molybdenum steel alloy 4130 Cadmium plating in accordance with SAE-AMS-C-81562, type II, class 3 or SAE
13、-AMS-QQ-P-416, type II, class 2 and NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. F Steel FN Chrome-molybdenum steel alloy 4130 NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. G Steel YG Chrome-molybdenum steel alloy 4130 Zinc plating with colorless passivate in accorda
14、nce with ASTM B633, type V, Fe/Zn 25. H Steel YH Chrome-molybdenum steel alloy 4130 Zinc phosphate finish in accordance MIL-DTL-16232, type Z, class1. 3/ J Steel YJ Chrome-molybdenum steel alloy 4130 Zinc plating with chromate conversion in accordance with ASTM B633; type II or III, Fe/Zn 5, or ASTM
15、 B695, type II, class 5. K Nickel-copper alloy UNS N04400 No additional finish. M High-chromium nickel alloy UNS N06690 No additional finish. N Steel YN Chrome-molybdenum steel alloy 4130 Zinc aluminum in accordance with ASTM F1136, grade 3, NC. P Steel YP Chrome-molybdenum steel alloy 4130 Zinc pla
16、ting with colorless passivate in accordance with ASTM B633, type VI, Fe/Zn 5. S No additional finish. Passivation in accordance with SAE-AMS2700, type 6 or 7. SN Corrosion resistant steel Passivation above and NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. T Titanium Anodize in accord
17、ance with SAE-AMS2488, type 2. V Steel Zinc-nickel in accordance with SAE-AMS2417, type 1. W Steel YW Chrome-molybdenum steel alloy 4130 Any zinc plating above. Z Steel YZ Chrome-molybdenum steel alloy 4130 Any zinc plating above with NAVAIR TCP in accordance with MIL-DTL-81706, type 2, class A. 1/
18、All materials and finishes shall be in accordance with MIL-DTL-52525. 2/ Embitterment test need not be run. 3/ Zinc phosphate finish is hexavalent chromium free. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-52525/38B 4 The operating pressu
19、re shall be as specified in table II. Maximum operating pressures are for low carbon steel fittings consult manufacturer for values on other materials. TABLE II. Maximum operating pressures of fittings. 1/ 2/ SAE dash number Hose ID inches (mm) psi MPa -08 .50 (12.70) 5000 34.5 -12 .75 (19.05) 4000
20、27.6 -16 1.00 (25.40) 4000 27.6 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. Over tightening torque shall be as specified in table III. Maximum over torque values are for low carbon steel fittings consult manufacturer for values on other materials. TABLE III. Ov
21、er-tightening torque for swivel nut. 1/ 2/ SAE dash number Tube OD inches (mm) Pound force foot (lbf-ft) N m -08 .50 (12.70) 37.5 51 -12 .75 (19.05) 75 102 -16 1.00 (25.40) 100 136 1/ Dimensions are in inches. 2/ Metric equivalents are given for information only. PIN: The PIN consists of the letter
22、“M” the specification sheet number, a dash, a number for the hose size a dash, a number for tube size, and a material finish designator. M 52525/38 -12 -12 A Size dash number for hose (see figure 1) Specification sheet numberM prefix Material/finish designator (see table I) Size dash number for tube
23、 (see figure 1) PIN example: M52525/38-12-12A, describes a 45bent tube flared female swivel .750 inch (19.05 mm) hose ID and .750 inch (19.05mm) tube, aluminum with an anodized finish. To the users of this document, it is recommended that the use of carbon steel material with cadmium plating be used
24、 only when the other materials and finishes specified in this document cannot meet performance requirements. Color identification. Color identification shall be in accordance with SAE-AS4841. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-52
25、525/38B 5 Marking shall include the manufacturers name or trademark, size, and hose identifier 100R12. Location of marking is optional. Harmonization to SAE-J516 cross reference PIN in table IV is for reference only. SAE style fittings may not have the same material/finish as required by MIL-DTL-525
26、25 and legacy with MIL-DTL-52471. TABLE IV. Harmonization to SAE-J516 cross reference PIN. 1/ PIN SAE PIN M52525/38-08-08 SAE J516 8-8 F242277 M52525/38-12-12 SAE J516 12-12 F242277 M52525/38-16-16 SAE J516 16-16 F242277 1/ Material and finish designators are omitted from PINs, see table I and SAE-J
27、846. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. Referenced documents. In addition to MIL-DTL-52525, this document references the following: MIL-A-8625 MIL-DTL-16232 MIL-DTL-52
28、471 MIL-DTL-52471/9 MIL-DTL-52471/10 MIL-DTL-81706 ASME B1.1 ASTM B633 ASTM B695 ASTM F1136 SAE-AMS-C-81562 SAE-AMS-QQ-P-416 SAE-AMS2417 SAE-AMS2488 SAE-AMS2700 SAE-AS4841 SAE-J516 SAE-J846 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - SH Air Force - 99 (Project 4730-
29、2007-094) DLA - CC Review activities: Army - CR4 Navy - AS, CG, MC, SA, YD NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
