1、 COMMERCIAL ITEM DESCRIPTION ADAPTER, STRAIGHT, PIPE TO TUBE, PIPE THREAD TO FEMALE SOLDER-JOINT, REFRIGERATION The General Services Administration has authorized the use of this commercial item description for all federal agencies. 1. SCOPE. This commercial item description (CID) covers the general
2、 requirements for wrought copper and copper alloy solder joint pressure fittings for use with copper water tubes in refrigeration systems. 2. CLASSIFICATION/PART OR IDENTIFCATION NUMBER (PIN). This CID uses a classification system which is included in the PIN as shown in the following example (see 7
3、1) AA59445 - 3-2 CID number Dash number 3. SALIENT CHARACTERISTICS. 3.1 Interface and physical dimensions. Fittings supplied to this CID shall be as specified herein (see figure 1). 3.2 Material and finish. Fitting material and finishes shall be copper and copper alloy, as specified in ASME B16.22.
4、 3.3 Design, construction, and performance. Fitting design, construction, and performance shall be in accordance with ASME B16.22. 3.4 Marking. Connectors supplied to this CID shall be marked with the manufacturers (MFRs) standard commercial PIN. (NOTE: The part number marked on the unit pack shall
5、be the CID PIN.) 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economi
6、cally advantageous life cycle costs. AMSC N/A FSC 4730 INCH-POUND A-A-59445A 6 August 2013 SUPERSEDING A-A-59445 22 June 1999 Comments, suggestions, or questions on this document should be addressed to: DLA Land and Maritime, Attn: VAI, P.O. Box 3990, Columbus, Ohio, 43218-3990 or emailed to FluidFl
7、owdla.mil. Since contact information can change, you may want to verify the currency of this address information using ASSIST Online Database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59445A 2 3.6 Workmanship. Conn
8、ectors shall be processed in such a manner as to be uniform in quality and shall be free from other defects that will affect life, serviceability, or appearance. 4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordan
9、ce with 23.403 of the Federal Acquisition Regulation (FAR). 5. PRODUCT CONFORMANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be
10、the same product offered for sale in the commercial marketplace. The Government reserves the right to require proof of such conformance. 6 PACKAGING. Preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES. 7.1 PIN. The PIN should be used for Government purposes t
11、o buy commercial products to this CID. See section 2 for PIN example. The PIN procedure is for government purposes and does not constitute a requirement for the contractor. Figure 1, figure 2, and table I are provided for configuration identification. SIZE MSIZE LSIZE LSIZE MFIGURE 1. Female adapter
12、 FIGURE 2. Male adapter. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59445A 3 TABLE I. Dash numbers. Dash numbers Female adapter (figure 1) Male Adapter (figure 2) Tube size, inches L x M -3-2F -3-2 3/8 X 1/4 -3-3F -3-3 3/8 X 3/8 -4-3F -4-3
13、1/2 X 3/8 -4-4F -4-1 1/2 X 1/2 -4-6F -4-6 1/2 X 3/4 -5-2F -5-2 5/8 X 1/4 -5-3F -5-3 5/8 X 3/8 -5-4F -5-4 5/8 X 1/2 -5-6F -5-6 5/8 X/3/4 -6-4F -6-4 3/4 X 1/2 6-6F -6-6 3/4 X 3/4 -7-4F -7-4 7/8 X 1/2 -7-6F -7-6 7/8 X 3/4 -9-6F -9-6 1 1/8 X 3/4 The PIN consists of the document identifier and a dash no.
14、 (see table I). The dash number denotes size in increments of 1/8 inch. PIN example AA59445-3-2: AA59445 - 3-2 Dash no. (see table I) Document identifier 7.2 Environmentally preferable material. Environmentally preferable materials should be used to the maximum extent possible to meet the requiremen
15、ts of this specification. As of the dating of this document, the U.S. Environmentally Protection Agency (EPA) is focusing efforts on reducing 31 priority chemicals. The list of chemicals and additional information is available on their website http:/www.epa.gov/osw/hazard/wastemin/priority.htm Inclu
16、ded in the EPA list of 31 priority chemicals are cadmium, lead, and mercury. Use of these materials on the list should be minimized or eliminated unless needed to meet the requirements specified herein (see Section 3). 7.3 Commercial and Government Entity (CAGE) code. For ordering purposes, inventor
17、y control, and submission of these fuse plugs to DLA Land and Maritime under the Military Parts Control Advisory Group (MPCAG) evaluation program, CAGE code 58536 should be used. 7.4 Sources of documents. FEDERAL REGULATIONS FAR Federal Acquisitions Regulations (FAR) (Copies of this document are ava
18、ilable online at http:/www.acquisition.gov/comp/far/index.html from the U.S. Government Printing Office, 732 North Capital Street, NW, Washington D.C. 20401-0001.) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59445A 4 Other Publications ASME I
19、NTERNATIONAL ASME B16.22 Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings (Copies of these documents are available online at http:/www.asme.org or from the ASME International, Three Park Avenue, New York, NY 10016-5990.) 7.5 Ordering data. The contractor order should specify the follow
20、ing: a. CID document number, revision and CID PIN. b. Product conformance provisions. c. Packaging requirements. 7.6 Cross reference data. See table II for PIN cross reference data. TABLE II. Cross reference data. MS35921 Tube size, inches AA59445 MS35921-3-2F MS35921-3-2 3/8 X 1/4 AA59445-3-2F AA59
21、445-3-2 MS35921-3-3F MS35921-3-3 3/8 X 3/8 AA59445-3-3F AA59445-3-3 MS35921-4-3F MS35921-4-3 1/2 X 3/8 AA59445-4-3F AA59445-4-3 MS35921-4-4F MS35921-4-4 1/2 X 1/2 AA59445-4-4F AA59445-4-4 MS35921-4-6F MS35921-4-6 1/2 X 3/4 AA59445-4-6F AA59445-4-6 MS35921-5-2F MS35921-5-2 5/8 X 1/4 AA59445-5-2F AA59
22、445-5-2 MS35921-5-3F MS35921-5-3 5/8 X 3/8 AA59445-5-3F AA59445-5-3 MS35921-5-4F MS35921-5-4 5/8 X 1/2 AA59445-5-4F AA59445-5-4 MS35921-5-6F MS35921-5-6 5/8 X/3/4 AA59445-5-6F AA59445-5-6 MS35921-6-4F MS35921-6-4 3/4 X 1/2 AA59445-6-4F AA59445-6-4 MS35921-6-6F MS35921-6-6 3/4 X 3/4 AA59445-6-6F AA59
23、445-6-6 MS35921-7-4F MS35921-7-4 7/8 X 1/2 AA59445-7-4F AA59445-7-4 MS35921-7-6F MS35921-7-6 7/8 X 3/4 AA59445-7-6F AA59445-7-6 MS35921-9-6F MS35921-9-6 1 1/8 X 3/4 AA59445-9-6F AA59445-9-6 7.7 National Stock Numbers (NSNs). The following is a list of identified NSNs assigned that correspond to this
24、 CID. This list may not be indicative of all possible NSNs associated with this CID (see table III). TABLE III. NSNs. NSN Size 4730-00-266-1835 -5-4 4730-00-941-5915 -5-2 4730-01-049-5819 -4-4 4730-01-096-9126 -3-2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license
25、from IHS-,-,-A-A-59445A 5 TABLE III. NSNs -Continued. 4730-01-230-6591 -5-4 4730-01-381-8650 -4-3 4730-01-383-5430 -5-6 7.8 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to the extent of the changes. MILITARY
26、 INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: GSA-FSS Custodians: Preparing activity: Army - GL DLA - CC Navy SH Air Force - 99 DLA - CC (Project 4730-2013-055) Review activities: Army - CE Navy - MC NOTE: The activities listed above were interested in this document as the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
