1、INCH-POUND MIL-DTL-55302/96F 20 August 2008 SUPERSEDING MIL-DTL-55302/96E 17 November 2004 DETAIL SPECIFICATION SHEET CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES: RECEPTACLE, WRAPPOST (REMOVABLE) HERMAPHRODITIC CONTACTS (.100 INCH SPACING) This specification is approved for use by all De
2、partments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-55302. AMSC N/A FSC 5935 FIGURE 1. Connector, receptacle (.100 inch spacing). Provided by IHSNot for ResaleNo reproduction or network
3、ing permitted without license from IHS-,-,-MIL-DTL-55302/96F 2 Inches mm Inches mm .001 0.03 .185 4.70 .003 0.08 .235 5.97 .005 0.13 .250 6.35 .007 0.18 .270 6.86 .015 0.38 .276 7.01 .086 2.18 .320 8.13 .091 2.31 .340 8.64 .096 2.44 .400 10.16 .098 2.49 .410 10.41 .100 2.54 .450 11.43 .102 2.59 .462
4、 11.73 .120 3.05 .560 14.22 .125 3.18 .625 15.88 .138 3.51 .163 4.14 Dimensions Dash number Number of contacts A .006 (.015) B .006 (.015) C D .006 (.015) E .006 (.015) F G .006 (.015) M .006 (.015) 01 24 1.100 (27.94) 1.236 (31.39) 1.240 (31.50) 1.400 (35.56) 1.900 (48.26) 2.200 (55.88) 1.260 (32.0
5、0) 1.270 (32.26) 02 28 2.300 (58.42) 2.436 (61.87) 2.440 (61.98) 2.600 (66.04) 3.100 (78.74) 3.400 (86.38) 2.460 (62.48) 2.470 (62.74) 03 72 3.500 (88.90) 3.636 (92.35) 3.640 (92.46) 3.800 (96.52) 4.300 (109.22) 4.600 (116.84) 3.600 (92.96) 3.670 (93.22) 04 96 4.700 (119.38) 4.836 (122.83) 4.840 (12
6、2.94) 5.000 (127.00) 5.500 (139.70) 5.800 (147.32) 4.860 (123.44) 4.870 (123.70) NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .010 (0.25 mm). 4. Dimensions are .162 (4.11 mm) hex across the flats by .052 deep
7、1.32 mm) 4 places. 5. Keying sockets shown are in positions 4 and D. FIGURE 1. Connector receptacle (.100 inch spacing) Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/96F 3 REQUIREMENTS Dimensions and configurations: See fi
8、gure 1. Material and finish: Contact: 0.020 inch thick phosphor bronze in accordance ASTM B139/B139M, composition A. Gold plate in accordance with ASTM B488, type 2, code D, class 1.27, over nickel plating in accordance with MIL-DTL-38999, appendix A, class 2, 30 to 100 microinches. Insulation: ASTM
9、 D5948, type SDG-F. Keying hardware: 2 each hex nuts and washers, stainless steel, class 300 in accordance with ASTM A582/A582M, passivated in accordance with SAE-AMS2700, type 2, and 2 each keying sockets, free machining brass in accordance with ASTM B16/B16M, UNS C36000 or ASTM B121/B121M, UNS C35
10、300, C34200 or ASTM B124/B124M, UNS C37700, ASTM B36/B36M, UNS C23000, C24000, C26000 or C26800, nickel plated in accordance with MIL-DTL-38999, appendix A. For direct government procurement the keying hardware shall be assembled to the connector. For other orders the keying hardware may be furnishe
11、d loose as specified in contract or order. Contact identification: The first and last contact in each row shall be identified by an alphabetical-numerical code (e.g., A01, B12). The letter designates the row and the number designates the contact position within that row. Every fifth contact in each
12、row shall have its identification mark molded in. Contact retention: 6 pounds. Mating and unmating: The maximum insertion force, in pounds, shall not exceed a value equal to .5 times the number of contacts, and the withdrawal force, in pounds, shall be a minimum of .11 times the number of contacts a
13、nd shall not exceed the measured insertion force. Contact separation force: 1 ounce minimum. Contact resistance: The contact resistance shall not exceed 20 milliohms. Dielectric withstanding voltage: Sea level: 1,000 volts rms, 60 Hz. High altitude: 300 volts rms, 60Hz. Current rating, maximum: 5 am
14、peres. Keying socket: When required, can be easily keyed to the desired positions by using a standard type wrench. Connectors are supplied with keying sockets in 4 and D positions. Mating connectors: Shall conform to MIL-DTL-55302/91, or MIL-DTL-55302/93 and MIL-DTL-55302/95. Contact insertion tool:
15、 Shall conform to MIL-I-81969/5. Contact removal tool: Shall conform to MIL-I-81969/4. Contact wrappost tool: Shall conform to MIL-DTL-55302/98. Part or Identifying Number (PIN): M55302/96-(dash number from figure I). Group submission: MIL-DTL-55302/90, MIL-DTL-55302/92, and MIL-DTL-55302/94. Provid
16、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55302/96F 4 Qualification: Qualification is not required for this specification sheet. First article testing (FAT): FAT shall be in accordance with MIL-DTL-55302, qualification inspection. Sample size
17、 6 connectors shall be subjected to the FAT. All sample units shall be subjected to the inspections in subgroup I. The sample units shall be divided equally into 3 groups of 2 and subjected to the inspection for their particular subgroups. Contacts shall be tested as specified in subgroup 4A or 4B
18、as applicable. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bi
19、dders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-55302, this document references the following: MIL-DTL-38999
20、MIL-DTL-55302/90 MIL-DTL-55302/91 MIL-DTL-55302/92 MIL-DTL-55302/93 MIL-DTL-55302/94 MIL-DTL-55302/95 MIL-DTL-55302/98 ASTM A582/A582M ASTM B16/B16M ASTM B36/B36M ASTM B121/B121M ASTM B124/B124M ASTM B139/B139M ASTM B488 ASTM D5948 SAE-AMS2700 MIL-I-81969/4 MIL-I-81969/5 CONCLUDING MATERIAL Custodia
21、ns: Preparing activity: Army CR DLA - CC DLA CC (Project 5935-2008-179) Review activities: Army AR, AT, AV, CR4, MI NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
