1、 MIL-DTL-83528/1E 19 November 2013 SUPERSEDING MIL-DTL-83528/1D 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI, CIRCULAR STRIP, .040 THROUGH .250 DIAMETER This specification is approved for use by all Departments and Agenc
2、ies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-DTL-83528. NOTES: 1. Dimensions are in inches; metric equivalents are given in .parenthesis and are for general information only. 2. Length shal
3、l be as specified on the purchase order. 3. Tolerance on flash shall be .008 (0.20 mm) on the extension and .005 (0.13 mm) on the thickness. FIGURE 1. EMI/RFI circular strip gasket. AMSC N/A FSC 5999 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
4、 IHS-,-,-MIL-DTL-83528/1E REQUIREMENTS: Design and interface: See figure 1 and table I. Material: Type A, B, C, D, E, F, H, J, K, L, or M. Part or Identifying Number (PIN): See table I. Supersession information: See table II. TABLE I. Dimensions. PIN 1/ M83528/001X Dimension A .005 2/ 3/ Cross secti
5、on 4/ area (cm2) 001 .040 (1.02) .008 002 .053 (1.35) .014003 .062 (1.57) .020 004 .070 (1.78) .025005 .080 (2.03) .032 006 .093 (2.36) .043007 .103 (2.62) .053 008 .119 (3.02) .072009 .125 (3.18) .079 010 .139 (3.53) .099011 .188 (4.78) .179 012 .216 (5.49) .236013 .250 (6.35) .316 1/ “X” in the PI
6、N shall be replaced by the applicable material type. Complete PIN example: M83528/001A001. 2/ Tolerance shall be .008 for parts over .200 in diameter. 3/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 4/ For calculation of volume resistivi
7、ty (for reference only). TABLE II. Supersession information. PIN 1/ M83528/001X Superseded DESC Drawing PIN 85103X 1/ 001 001002 002003 003004 004 005 N/A 006 005007 006008 007 009 008010 009011 N/A 012 010 013 N/A 1/ “X” in the PIN indicates the applicable material type. Changes from previous issue
8、 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to eva
9、luate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. This document references MIL-DTL-83528. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license
10、 from IHS-,-,-MIL-DTL-83528/1E Custodians: Preparing activity: Army CR DLA-C Nav EC Air Force 85 (Project 5999-2013-011) DLA CC Review Activities: Air Force 19, 99 NSA NS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
