1、 MIL-DTL-83528/11E 12 August 2013 SUPERSEDING MIL-DTL-83528/11D 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI, HOLLOW O-STRIP This specification is approved for use by all Departments and Agencies of the Department of Def
2、ense. The requirements for acquiring the relay described herein shall consist of this specification and the latest issue of MIL-DTL-83528. NOTE: Length shall be as specified on the purchase order. FIGURE 1. EMI/RFI gasket, elastomer, hollow O-strip. FSC 5999 INCH-POUND Provided by IHSNot for ResaleN
3、o reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/11E 2 REQUIREMENTS: Design and interface: See figure 1 and table I. Material: Type A, B, C, D, E, F, J, K, L, or M. Part or Identifying Number (PIN): See table I. Supersession information: See table II. TABLE I. Dimens
4、ions. PIN 1/ M83528/011X Nominal dimensions 2/ 3/ Cross section area (cm2) 4/ A (width) B (height) 001 0.125 (3.18) 0.045 (1.14) 0.069 002 0.156 (3.96) 0.050 (1.27) 0.111 003 0.250 (6.35) 0.125 (3.18) 0.237 004 0.312 (7.92) 0.192 (4.88) 0.306 005 0.375 (9.53) 0.250 (6.35) 0.396 006 0.125 (3.18) 0.06
5、2 (1.57) 0.060 007 0.103 (2.62) 0.040 (1.02) 0.046 008 0.177 (4.50) 0.079 (2.01) 0.127 1/ “X” in the PIN shall be replaced by the applicable material type. Complete PIN example: M38528/011A001. 2/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information o
6、nly. 3/ Tolerance shall be as follows: Dimensions Tolerance Under .101 (2.57) .101 to .200 (2.57 to 5.08) .201 to .300 (5.10 to 7.62) .301 to .500 (7.62 to 12.70) .005 (0.13) .008 (0.20) .010 (0.25) .015 (0.38) 4/ For calculation of volume resistivity (for reference only). TABLE II. Supersession inf
7、ormation. PIN 1/ M83528/011X Superseded DESC Drawing PIN 85110X 1/ 001 001002 002003 003 004 004005 005006 N/A 007008 N/A 1/ “X” in the PIN indicates the applicable material type. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes
8、from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the margi
9、nal notations and relationship to the last previous issue. Referenced documents. This document references MIL-DTL-83528. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/11E 3 Custodians: Preparing activity: Army CR DLA CC Navy EC Air Fo
10、rce 85 (Project 5999-2013-008) DLA CC Review activities: Air Force 19, 99 NSA NS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
