1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONMENT RESISTING), PLUG, (RFI, BAYONET COUPLING, CRIMP PIN CONTACT), (SERIES III, CLASSES G, M, R, T, W, AND Z) This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements fo
2、r acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83723. FIGURE 1. Dimensions and configurations. AMSC N/A FSC 5935 INCH-POUND MIL-DTL-83723/78E 19 August 2009 SUPERSEDING MIL-DTL-83723/78D 15 September 2006 Provided by IHSNot for ResaleNo reproduction or
3、 networking permitted without license from IHS-,-,-MIL-DTL-83723/78E 2 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/78E 3 Shell size A max G min H J L min U max V 8 .312 .352 .415
4、424 .540 .545 .632 .776 .025 10 .388 .428 .517 .526 .662 .667 .760 .906 .031 12 .558 .598 .687 .696 .832 .837 .930 1.078 .031 14 .627 .667 .756 .765 .901 .906 .999 1.141 .031 16 .772 .794 .883 .892 1.028 1.033 1.126 1.266 .031 18 .860 .900 .989 .998 1.134 1.139 1.232 1.375 .031 20 .985 1.025 1.114
5、1.123 1.261 1.266 1.357 1.510 .031 22 1.110 1.150 1.239 1.248 1.384 1.389 1.482 1.625 .031 24 1.235 1.275 1.364 1.373 1.511 1.516 1.607 1.760 .031 FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI
6、L-DTL-83723/78E 4 Inches mm Inches mm Inches mm Inches mm Inches mm .008 0.20 .177 4.50 .552 14.20 .900 22.86 1.232 31.29 .015 0.38 .182 4.62 .558 14.17 .901 22.89 1.235 31.37 .018 0.48 .185 4.70 .598 15.19 .906 23.01 1.239 31.47 .020 0.51 .200 5.08 .627 15.93 .930 23.62 1.248 31.70 .022 0.56 .204 5
7、18 .632 16.05 .985 25.02 1.261 32.03 .025 0.64 .259 6.58 .662 16.81 .989 25.12 1.266 32.16 .031 0.79 .312 7.92 .667 16.94 .998 25.35 1.275 32.39 .032 0.81 .316 8.03 .678 17.22 .999 25.37 1.357 34.47 .042 1.07 .320 8.13 .687 17.45 1.025 26.04 1.373 34.87 .046 1.17 .330 8.38 .696 17.68 1.028 19.84 1.
8、375 34.93 .065 1.65 .352 8.94 .756 19.20 1.033 26.24 1.384 35.15 .069 1.75 .366 9.30 .760 19.30 1.078 27.38 1.389 35.28 .090 2.29 .383 9.73 .765 19.43 1.110 28.19 1.482 37.64 .097 2.46 .388 9.86 .772 19.61 1.114 28.30 1.510 38.35 .101 2.57 .415 10.54 .776 19.71 1.123 28.52 1.511 38.38 .106 2.69 .424
9、 10.77 .794 20.17 1.126 28.60 1.516 38.51 .112 2.84 .428 10.87 .832 21.13 1.134 28.80 1.607 40.82 .125 3.18 .517 13.13 .837 21.26 1.139 28.93 1.625 41.28 .138 3.51 .526 13.36 .860 21.84 1.141 28.98 1.760 44.70 .144 3.66 .540 13.72 .883 22.43 1.150 29.21 .170 4.32 .545 13.84 .892 22.66 1.230 31.24 NO
10、TES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances are .005 (0.13 mm) for three place decimals and .01 (0.25 mm) for two place decimals and 1o for all angles. 4. Rear accessory interchangeability dimensions shall be in ac
11、cordance with MIL-DTL-83723. 5. See table I for contact cavities requiring this dimension. FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/78E 5 REQUIREMENTS: Dimensions and configura
12、tions: See figure 1. For insert arrangements, see MIL-STD-1554 and table I. TABLE I. Inserts requiring reduced diameters for raised seal barriers on contact cavities. Shell size Insert arrangements Contact cavities 8 03 1, 2, 3 10 06 1, 2, 3, 4, 5, 6 For connector accessories, see SAE-AS85049. This
13、connector mates with MIL-DTL-83723/71 and MIL-DTL-83723/73. Mating force: Shall not exceed the values specified in the procurement document by more than 20 percent. RFI spring strip shall have a minimum of six fingers per inch and shall point to rear of connector. Part or Identifying Number (PIN) ex
14、ample: M83723/ 78 W 22 55 N Military designation Specification sheet number Class Shell size Insert arrangement Polarizing position Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83723/78E 6 Changes from previous issue. Marginal notations ar
15、e not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83723, this document references the following: MIL-DTL-83723/71 MIL-DTL-83723/73 MIL-STD-1554 SAE-AS85049 CONCLUDING MATERIAL Custodians:
16、Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 DLA - CC Review activities: (Project 5935-2008-160) Army - AR, MI Navy - EC Air Force 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
