1、I MIL-H-9850C 10 June 1977 SUPERSEDING MIL-H-9850B 11 January 1974 - MILITARY SPECIFICATION HINGE, BUTT CONTINUOUS (PIANO) This specffication is approved for use by all Department and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers one type of continuous butt, hi
2、nge, (piano) as specified in the supplement. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. The following documents, of the issue in effect on date of invitation for bids or requests for proposal, form a part of this specification to the extent specified herein. SPECIFICATIONS Federal PPP-B-601 -
3、Boxes, Wood, Cleated-Plywood PPP-B-621 - Boxes, Wood, Nailed and Lock-Corner PPP-B-636 - Boxes, Shipping, Fiberboard PPP-B-640 - Boxes, Fiberboard, Corrugated, Triple-Wall Military MIL-P-116 - Preservation-Packaging, Methods of Beneficial comments (recommendations, additions, deletions.) and any per
4、tinent data which may be of use in improving this document should be addressed to: Commander, US Army Armament Research and .Development Command, ATTN: DRDAR-TST, Rock Island, IL 61201 by using the self- addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of t
5、his document or by letter. FSC 5340 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-9850C STANDARDS Federal Fed, Std. No. 356 Military MIL-STD-105 MIL-STD-129 MIL-STD-147 - Commercial Packaging of Supplies and Equipment - Sampling Procedures an
6、d Tables for Inspection by Attributes I Marking for Shipment and Storage - Palletized and Containerized Unit Loads 40“ x 48“ Pallets, Skids , Runners, or Pallet-Type Base (See Supplement 1 for list of associated MS sheet form standards.) (Copies of specifications, standards, drawings and publication
7、s required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer . ) 3.1 Military standards for individual sizes of hinges. The indivi- dual item requirements shall be as specified herein and in accorda
8、nce with the applicable Military standards. In the event of any conflict between requirements of this specification and the Military standard or dpplicable drawing or specifications the latter shall govern. 3.2 Materials. The materials for the hinges described herein shall be in accordance with the
9、applicable MS standard or applicable drawings or specification, 3.3 Design and construction. The hinges shall.be of the design, construction, and physical dimensions specified herein and on the appli- cable MS standards. 3.3.1 Pins. Pins of assembled hinges shall securely fasten to- gether the leave
10、s of the hinge. 3.3.2 Leaves. Separate leaves, as applicable, shall be in accordance with the pertinent dimensional requirements of the applicable MS standards. The leaves of the assembled hinge shall match to permit freedom of movement without excessive looseness. 2 Provided by IHSNot for ResaleNo
11、reproduction or networking permitted without license from IHS-,-,-MIL-H-9850C 3.4 Workmanship. Workmanship shall conform lubricants and all other defects which might affect their serviceability. 4. QUALITY ASSURANCE PROVISIONS 4.1 ResponsibiXity for inspection. Unless otherwise specified in the cont
12、ract, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the con- tract, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless dis
13、approved by the Government. The Government reserves the right to per- form any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Classification of inspections. The inspection requireme
14、nts spec- fied herein are classified as follows: a. Quality conformance inspection (see 4.31 : b. Packaging inspection (see 4.4) . 4.3 pality conformance inspection. 4.3.1 Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical examination. 4.3.1
15、.1 Inspection lot. An inspection lot shall consist of all hinges made of the same materia1,metal thickness, and pin diameter produced under the same manufacturing conditions and offered for inspection at one time. Hinges of different -lengths may be combined to form one lot for sampling purposes. 4.
16、3.1.2 Sampling plan. Sampling for examination shall be in accor- dance with MIL-STD-105, Inspection Level I. 4.3.1.3 Examination. 4.3.1.3.1 Samples. Samples selected in-accordance with 4.3.1.2 shall be examined for the-.defects specified in Table I. The Acceptable Quality Level (AQL) shall be 1.0 pe
17、rcent defective. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-9850C TABLE I Classification of D,efects Inspection Categories Defects Method Critical None defined Major : 101 Hinge is incomplete; component parts Visual 102 Type o5 finish no
18、t as specified or blistered, Visual missing (3.3). peeled, chipped, or of no film or thin film affecting serviceability (3.4). 103 Hinge not fabricated of specified material SIE* 104 Hinge does not comply with specified dimensions SIE* (3.2) - (3.3) 105 Assembly; anchor of hinge pin and straightness
19、 Visual of (3.4) . Minor: None defined. * Standard inspection equipment. 4.3.1.4 Rejected lots. If an inspection lot is rejected, the supplier may screen out the defective units, and resubmit for reinspection. Resubmitted- lots shall be inspected using tightened inspection. Such lots shall be separa
20、te from new lots and shall be clearly identified as reinspected loks 4.4 Packaqing inspection. Packaging inspection for preservation, pack- ing and marking shall be in accordance with section 5 of this specification and the documents specified herein. 5. PACKAGING. 5.1 Preservation. Preservation sha
21、ll be level A or B, or comercial, in unit and intermediate quantities as specifed, (see 6.2). 5.1.3. Level A, 5.1.1.1 Cleaning. Hinges shall be cleaned in accordance with process C-1 of MIL-P-116. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. M
22、IL-H-9850C 5.1.1.2 Drying. Hinges.shall.be dried in accordance with any applic- able procedure of MIL-P-116. 5.1.1.3 Preservative application. None.required. 5.1.1.4 Unit pack. The-unit pack for each individual hinge shall conform to method 1C-3 of MIL-P-116. Physical protection shall be applied as
23、applicable. 5.1.1.5 Intermediate pack. Hinges of one size, unit pack as above (see 5.1.1.41, shall be placed in intermediate containers conforming to PPP-B-636, Type CF, Class Weather Persistant, Variety SW, Grade optional, Style RSC. The containers shall be the minimum size to adequately hoLd a uni
24、form quantity of hinges. Intermediate containers shall contain multiples of 5 unit packs not to exceed 50 unit packs. No intermediate pack is required when the total quantity shipped to a single destination is less than 50 unit packs. 5.1.2 Level B. 5.1.2.1 Cleaning. Shall be the same as Level A (se
25、e 5.1,l.l). 5.1.2.2 Drying. Shall be the same as Level A (see 5.1.1.2). 5.1.2.3 Preservative application. Shall be the same as Level A (see 5.1.1.3). 5.1.2.4 Unit pack. The unit pack for each hinge shall conform to method III of MIL-P-116. 5.1.2.5 Intermediate pack. The intermediate pack shall be th
26、e same as Level A (see 5.1.1.5) except that class domestic fiberboard shall be used in lieu of class weather resistant. 5.1.3 Commercial. Preservation shall be in accordance with Fed. Std. No. 356. 5.2 Packinq. Packing shall be level A or B, or commercial, as speci- fied (see 6.2). 5.2.1 Level; A. H
27、inges shall be packed in a minimum size shipping container conforming to hPP-B-621, Class 2, Style optional, or PPP-B-.601, be in accordance with the applicable container specification. I Overseas type, Style optional, Grade B. Closures and reinforcement shall 5 Provided by IHSNot for ResaleNo repro
28、duction or networking permitted without license from IHS-,-,-MIL-H-9850C 5.2.2 Level B. Hinges shall be packed-in a minimum size shipping container conforming to PPP-B-636, Type CF, Class weather resistant, Variety, Grade and Style optional or PPP-B-640, Class 2, Style optional. Closure and reinforc
29、ement shall be in accordance with the applicable container specification. 5.2.2.1 Palletized load. A uniform quantity of hinges shall be palletized in accordance with MIL-STD-147. 5.2.3 Commercial. Packing shall be in accordance with Fed. Std. NO. 356. 5.3 Marking. 5.3,1 Levels A and B. Marking shal
30、l be in accordance with MIL-STD-129. 5.3,2 Commercial. Marking shall be in accordance with Fed. Std. No. 356. 6. NOTES 6.1 Ztended use, The continuous butt piano hinge covered by this specification is intended for use on cases, chests and any other adaptable surf ace. 6.2 Ordering data. Procurement
31、documents should specify the following: e a. Title, number and date of this specification. b. Part number. c. Selection of applicable level of protection (A or B), or com- mercial packaging (see 5.1, 5.2, and 5.3). Custodians: Army - WC Air Force -e 99 Review activities : Army - AV, EA, EL, GL, MI DSA - IS User activities: Wny - AR, ME, MU Navy - AS, MC R- “ “ Preparing activity: Army - WC Project Number: 5340-1195 *U.S. GOVERNMENT PRINTING OFFICE: 1977-703-020/2%60 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
