1、AMSC N/A FSC 5915 MIL-PRF-15733/55F 28 October 2008 SUPERSEDING MIL-PRF-15733/55E 31 March 2003 PERFORMANCE SPECIFICATION SHEET FILTERS, RADIO INTERFERENCE, HERMETICALLY SEALED STYLE FL85 * This specification sheet is approved for use by all Depart- ments and Agencies of the Department of Defense. T
2、he requirements for acquiring the filters described herein shall consist of this specification sheet and MIL-PRF-15733. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are in parentheses. 3. Metric equivalents are given for general information only. 4. Circuit diagram is for information on
3、ly. 5. Mounting hardware (internal-tooth lockwasher and hex nut) shall be supplied with filter. 6. Terminal shape and angular orientation optional. FIGURE 1. Case dimensions and circuit configurations. INCH-POUND MIL-PRF-15733/55 IS INACTIVE FOR NEW DESIGN AFTER 28 OCTOBER 2008. FOR NEW DESIGN USE M
4、IL-PRF-15733/73. SEE TABLE IV FOR SUBSTITUTION DATA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-15733/55F 2 TABLE I. Filter dimensions. A B C Dash number Min Max Min Max Min Max 0001 2.907 (73.84) 3.093 (78.56) 1.063 (27.00) 1.187 (30.15
5、) .526 (13.36) .536 (13.61) 0002 2.907 (73.84) 3.093 (78.56) 1.063 (27.00) 1.187 (30.15) - .531 (13.49) 0003 2.31 (58.7) 2.43 (61.7) 1.235 (31.37) 1.265 (32.13) .365 (9.27) .385 (9.78) D E F Dash number Min Max Min Max Min Max 0001 .359 (9.12) .391 (9.93) .625 (15.88) .781 (19.84) .282 (7.16) .406 (
6、10.31) 0002 .359 (9.12) .391 (9.93) .625 (15.88) .781 (19.84) .282 (7.16) .406 (10.31) 0003 .47 (11.9) .53 (13.5) - 1.43 (36.32) - .50 (12.70) REQUIREMENTS: Dimensions and configuration: See figure 1 and table I. Weight: 5.0 ounces, maximum (0001, 0002). Case: Metallic, hermetically sealed. Case and
7、 hardware finish: In accordance with MIL-PRF-15733. Pure tin finish is prohibited. Terminals: Solderable (see figure 1). Operating temperature range: -55C to +85C Rated voltage: 400 V dc or 125 V ac at 400 Hz. Rated current: Amperes dc or ac (rms) Dash nos. 5 0001 10 0002 2 0003 DC resistance: 0.072
8、 ohm, maximum. Insertion loss: See table II. Seal: In accordance with MIL-PRF-15733. Capacitance to ground: In accordance with MIL-PRF-15733. Measured capacitance: Between 0.72 and 1.44 F (0001 only). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M
9、IL-PRF-15733/55F 3 Temperature rise: 25C, maximum. Dielectric withstanding voltage: In accordance with MIL-PRF-15733. The following details and exceptions shall apply: Test voltage - shall be 2 times rated dc voltage applied between either terminal and case. The test voltage shall be applied and dis
10、charged through a resistance of at least 1 ohm per volt (0001 and 0002 only). Barometric pressure (reduced): In accordance with MIL-PRF-15733. The following exception shall apply: Test altitude: 80,000 feet (0.83 inch of mercury) for 0001 and 0002. Insulation resistance: In accordance with MIL-PRF-1
11、5733. Insulation resistance shall be at least 550 megohms for -0001 and -0002 and shall be 1,000 megohm-microfarads minimum for the -0003. Voltage drop: 1.0 V rms, maximum (-0001 and -0002) and .5 V dc, Max (-0003). Insertion loss: In accordance with MIL-PRF-15733 and tables II and III. Terminal str
12、ength: In accordance with MIL-PRF-15733 and Method 211, MIL-STD-202; test condition A (pull). The following details shall apply: Applied force: 5 pounds. The force shall be applied in a direction parallel to the longitudinal axis of the filter. Slight deformation at the solder tab shall be allowable
13、 provided no cracks, fractures or other damage to the terminal result from this test. Flashpoint of impregnant or potting compound: In accordance with MIL-PRF-15733. Minimum allowable flashpoint shall be +145C. Salt atmosphere (corrosion): In accordance with MIL-PRF-15733 and Method 101, MIL-STD-20
14、2, test condition A, (-0001 and -0002); test condition B (-0003). Shock (specified pulse): In accordance with MIL-PRF-15733 and Method 213, MIL-STD-202; test condition I. The following details and exceptions shall apply: Mounting: Filters shall be rigidly mounted by the body. Insertion loss test: No
15、t applicable. Vibration, high frequency: In accordance with MIL-PRF-15733 and Method 204, MIL-STD-202; test condition B. The following exception shall apply: Electrical current load shall not be applied to filters during the vibration test. Life: In accordance with MIL-PRF-15733 and Method 108, MIL-
16、STD-202; test condition B. The following exception shall apply: Test current: 5 amperes, rms (0001 and 0002) and 2 amperes (0003) at 400 Hz. Part or Identifying number (PIN): M15733/55- (dash number from table I). Provided by IHSNot for ResaleNo reproduction or networking permitted without license f
17、rom IHS-,-,-MIL-PRF-15733/55F 4 TABLE II. Insertion-loss (dB) (full load) versus frequency (MHz). Minimum insertion loss full load in accordance with MIL-STD-220 at +25C Dash number 0.15 MHz 0.3 MHz 0.6 MHz 1 MHz 10 MHz 20 MHz 0001 40 58 76 80 80 80 0003 .15 MHz to 10 GHz 60 TABLE III. Insertion-los
18、s (dB) (no load) versus frequency (MHz). Minimum insertion loss no load in accordance with MIL-STD-220 at +25C Dash number 0.15 MHz 0.3 MHz 0.5 MHz 1 MHz 10 MHz 20 MHz 40-500 MHz 100 MHz 400 MHz 1000 MHz 0001 54 73 85 94 84 84 67 N/A N/A 64 0002 54 N/A 85 94 84 N/A N/A 80 80 N/A * TABLE IV. Substitu
19、tion Data Inactive PIN Superseding PIN M15733/55-0001 M15733/55-0002 M15733/55-0003 M15733/73-0042 M15733/73-0045 M15733/73-0039 or -0040 * Referenced documents. In addition to MIL-PRF-15733, this document also references the following: MIL-PRF-15733/73 MIL-STD-202 MIL-STD-220 * Changes from previou
20、s issue. The margins of this specification sheet are marked with asterisks to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautione
21、d to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing activity: Army - CR DLA - CC Navy - EC Air Force - 85 (Project 5915-2008-019) DLA - CC Review activities: Navy - SH Ai
22、r Force - 99 * NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
