1、AMSC N/A FSC 5920 MIL-PRF-19207/7N 5 December 2013 SUPERSEDINGMIL-PRF-19207/7M 22 January 2007 PERFORMANCE SPECIFICATION SHEET FUSEHOLDERS, EXTRACTOR POST TYPE, BLOWN FUSE INDICATING, TYPE FHL16G This specification is approved for use by all Departments and Agencies of the Department of Defense The
2、requirements for acquiring the product described herein shall consist of this specification and MIL-PRF-19207. See notes on page 2. FIGURE 1. Type FHL16G fuseholder. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/7N 2 Ltr In
3、ches mm Ltr Inches mm Min Max Min Max Min Max Min Max A 4.380 (REF) 111.25 (REF) M .245 .255 6.22 6.48 B .091 .101 2.311 2.565 N 8.19 (REF) 208.03 (REF) C 1.820 (REF) 46.23 (REF) P 4.25 (REF) 107.95 (REF) D 1.250 (REF) 31.75 (REF) R 1.75 (REF) 38.10 (REF) E 3.920 3.960 99.57 100.58 S 1.63 (REF) 41.4
4、0 (REF) F .055 .065 1.40 1.65 T 2.42 2.46 61.47 62.48 G 1.630 (REF) 41.40 (REF) U 1.23 1.27 31.24 32.26 H 3.670 3.710 93.22 94.23 V .339 .349 8.61 8.86 J 3.170 3.210 80.52 81.53 W 1.808 1.818 45.92 46.18 K 2.13 (REF) 54.10 (REF) X 1.307 1.317 33.20 33.45 L .245 .255 6.22 6.48 Y 2.933 2.943 74.50 74.
5、75 NOTES: 1. Dimensions are in inches. 2. Unless otherwise specified, tolerances are .005 (0.13 mm) for three placed decimals and .02 (0.51 mm) for two place decimals. 3. Metric equivalents are given for general information only. 4. Cap and body molding material: It is suggested that type MAI-60, GD
6、I-30F or SDG-F of American Society for Testing and Materials ASTM-D5948 be considered for meeting the cap and body molding material requirements of this specification. ASTM-D3935 is also suggested as guidance for cap material. FIGURE 1. Type FHL16G fuseholder - Continued. Provided by IHSNot for Resa
7、leNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/7N 3 REQUIREMENTS: Interface and physical dimensions: See figure 1. Cap and body molding material: Cap and body molding materials shall be selected to enable the fuseholder to meet the performance requirements of th
8、is specification. Additional information and guidance on body molding material are specified in the notes. Fuse accommodation: MIL-PRF-15160, styles F20 and F64 (or equivalent size and styles). Poles: One Rating: 101-200 amperes, 90-500 volts. Panel thickness: 0.250 inch (6.35 mm) maximum. Indicatin
9、g: Neon lamp with clear cap. Lamp series resistor: MIL-PRF-39017/2, two resistors, 160,000 ohms, 0. 5 watt. One each lamp lead. Terminals: Stud type, .375-16UNC-2A thread. Enclosure: Dripproof. Test fuses: Temperature rise: F64C500V200A of MIL-PRF-15160/64. Short circuit: F64C500V200A of MIL-PRF-151
10、60/64. Mechanical shock: Method I of MIL-PRF-19207. Terminal strength: 20 pounds. Fuse clip retention force: Lower clip: 5 to 7 pounds. Cap clip: 13 to 15 pounds. Salt atmosphere (corrosion): Test condition B. Mounting hardware: Screw: .3125-18UNC-2A, truss head, 3 inches long (min) with sealing was
11、her. Nut: .3125-18UNC-2B Hex. A threaded metal insert may be used in lieu of nut. Part or Identifying Number (PIN): FHL16G-001. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/7N 4 Referenced documents. In addition to MIL-PRF-19207, thi
12、s document references the following: MIL-PRF-15160 MIL-PRF-15160/64 MIL-PRF-39017/2 ASTM-D3935 ASTM-D5948 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no li
13、ability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing Activity: Army - CR DL
14、A - CC Navy - SH Air force - 85 (Project 5920-2013-029) DLA - CC Review Activities: Army - AR, AT, CR4, MI Navy - AS, EC, MC, OS Air Force - 70, 71, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
