1、AMSC N/A FSC 5945 INCH-POUND MIL-PRF-6106/20D 1 November 2011 SUPERSEDING MIL-PRF-6106/20C 10 November 2000 PERFORMANCE SPECIFICATION SHEET RELAYS, ELECTROMAGNETIC, MAGNETIC LATCH, 25 AMPERES, SPDT, HERMETICALLY SEALED Inactive for new design after 15 November 2002. No superseding document. This spe
2、cification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the relay described herein shall consist of this specification and MIL-PRF-6106 FIGURE 1. Relay, outline drawing.Provided by IHSNot for ResaleNo reproduction or networking perm
3、itted without license from IHS-,-,-MIL-PRF-6106/20D 2 FIGURE 1. Relay, outline drawing - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/20D 3 Inches mm Inches mm Inches mm .001 0.03 .156 3.96 .525 13.34 .002 0.05 .172 4.37 .5
4、62 14.27 .003 0.08 .234 5.94 .625 15.88 .005 0.13 .250 6.35 .630 16.00 .020 0.51 .270 6.86 1.010 25.65 .040 1.02 .281 7.14 1.025 26.04 .050 1.27 .300 7.62 1.062 26.97 .062 1.57 .375 9.52 1.396 35.46 .093 2.36 .432 10.97 1.406 35.71 .100 2.54 .485 12.32 1.446 36.73 .150 3.61 .500 12.70 1.718 43.64 NO
5、TES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .010 (0.25 mm). 4. Terminal numbers need not appear on the relay header provided there is affixed to the relay a suitable legible circuit diagram that identifie
6、s each terminal location specified. 5. Note to observe polarity must appear on relays. 6. Hook terminals will accept one No. 12 AWG stranded wire. 7. Socket pin terminals shall provide the operational, environmental, and interface characteristics to provide a reliable interconnect to gold-plated con
7、tacts. Terminals shall be gold plated. Gold plating of the polarizing pin is optional. One system for gold plating that may be used is ASTM B488, type 3, class 1.25 with a nickel underplate of 50 to 150 microinches thick. The gold plating system shall enable the product to meet the performance requi
8、rements of this specification and shall be approved by the qualifying activity. 8. Gasket shall provide a reliable seal between the relay and mating socket that will meet the environmental, operational, and interface requirements of the relay with the mating socket. The gasket shall have shore hardn
9、ess 20 5, thickness .050 .005. Gasket material according to SAE-AMS 3332 has been considered acceptable. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/20D 4 REQUIREMENTS Weight: 0.10 pound maximum. Temperature range 1/: -70C to +125C.
10、Maximum altitude-rating: 80,000 feet. Shock g-level: 200 g. Duration: 6 milliseconds. Maximum duration contact opening: 10 microseconds. Vibration-sinusoidal: G-level: 30 g. Frequency range: 10-3,000 Hz. Vibration-random: Applicable specification: MIL-STD-202, method 214, test condition IG. Duration
11、: 15 minutes, each plane. Strength of terminals and mounting studs: Applicable. Terminal solderability: Applicable to solder pin and solder hook terminals only. Acceleration: 15 g. Insulation resistance, initial: 100 megohms. Afterlife or environmental tests: 50 megohms. Dielectric withstanding volt
12、age (sea level): Initial After life tests Coil to case and coil to coil 1,000 V rms 1,000 V rms All other points 1,250 V rms 1,000 V rms Dielectric withstanding voltage (altitude) 2/: 80,000 feet 300,000 feet Coil to case and coil to coil 250 V rms 500 V rms All other points 350 V rms 500 V rms _ 1/
13、 For full rated load, maximum temperature, and altitude, use no. 12 wire or larger. Solder hook relays will be mounted to limit mounting bracket temperature to 135C. 2/ Dielectric withstanding voltage rating may be improved by suitable insulation of terminals and wiring after installation. Plug in r
14、elays, with suitable gasket compressed, will have dielectric withstanding voltage capabilities at 80,000 feet over 500 V rms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/20D 5 Maximum contact drop, initial: 0.150 volt. After life tes
15、t: 0.175 volt. Overload current: 50 amperes dc, 80 amperes ac, 400 Hz. Rupture current: 60 amperes dc, 100 amperes ac, 400 Hz. Duty rating: Continuous. Part or Identifying Number (PIN): M6106/20- (plus dash number from table I). Example: M6106/20-001. Qualification by similarity: See MIL-PRF-6106. S
16、uspension of inspection. Group B and Group C inspections may be suspended at the discretion of the qualifying activity. TABLE I. Dash numbers and characteristics. Dash numbers Coil data Time-milliseconds maximum 1/ Term-inal type Mount-ing style Coil Nominal Max Max pick-up voltage Ope-rate Re-set B
17、ounce Volts (V dc) 2/ Res 10% Volts Amp Nom-inal 3/ High temp test Cont cur- rent test Main NO NC -001 X1-X2 Y1-Y2 28 600 29 .050 18 19.8 22.5 10 10 1.0 1.0 Solder hook RVFM -002 X1-X2 Y1-Y2 28 600 29 .050 18 19.8 22.5 10 10 1.0 1.0 Plug-in RVFM -003 X1-X2 Y1-Y2 28 600 29 .050 18 19.8 22.5 10 10 1.0
18、 1.0 Solder hook HFM 1/ With nominal coil voltage. 2/ Caution: Use of any coil voltage less than nominal coil voltage will compromise the operation of the relay. 3/ Over temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/
19、20D 6 TABLE II. Rated contact load (amperes per pole) case grounded. Type of load Life opera-ing cycles X 10328 V dc 115 V ac,1 phase 115/200 V ac, 3 phase 1/ See appro-priate notes Main Aux Main Aux Main Aux NO NC NO NC 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz 400 Hz 60 Hz Resistive 50 25 25 25 2/ In
20、ductive 10 12 12 Inductive 20 15 Motor 50 10 10 10 Lamp 50 5 5 5 Transfer, load 3/ Mechanical life reduced current 200 6 6 6 Intermediate current APPLICABLE (See MIL-PRF-6106) Mixed loads APPLICABLE (See MIL-PRF-6106) 1/ Absence of value indicates relay is not rated for 3 phase application. 2/ For f
21、ull rated load maximum temperature and altitude use no. 12 wire or larger. Solder hook relays to be mounted to limit mounting bracket temperature to 135C. 3/ Transfer load indicates relay suitable for transfer between unsynchronized ac power supplies at rating indicated. Provided by IHSNot for Resal
22、eNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-6106/20D 7 Qualification by similarity: If the relays produced in accordance with this specification sheet are similar in design and construction to those covered by MIL-PRF-6106/19 (except for the coils), then reduced qua
23、lification by similarity is authorized. Manufacturers shall be qualified to MIL-PRF-6106/19 and MIL-PRF-83536. Qualification by similarity requirements are listed in table III. TABLE III. Qualification by similarity. Inspection Number of units Group A acceptance tests 7 1/ Vibration 2/ Resistive loa
24、d, ac Group A acceptance tests 2 Shock 2/ Inductive load, dc Group A acceptance tests 2 Acceleration 2/ Intermediate current 3/ Group A acceptance test 3 1/ Four units of dash number -002 and three units of dash number -003. All seven relays shall receive group A acceptance testing in accordance wit
25、h MIL-PRF-6106. The seven relays shall then be subdivided into three groups as shown above for the remaining inspections. 2/ One unit of dash number -002 and one unit of dash number -003. 3/ Three units required for mixed loads testing. Provided by IHSNot for ResaleNo reproduction or networking perm
26、itted without license from IHS-,-,-MIL-PRF-6106/20D 8 Referenced documents: MIL-PRF-6106 MIL-PRF-6106/19 MIL-PRF-83536 MIL-STD-202 ASTM-B488 SAE-AMS3332 The margins of this specification are marked with vertical lines to indicate where modifications from this revision were made. This was done as a c
27、onvenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations. Custodian: Preparing activity: Air Force
28、 - 85 DLA - CC DLA - CC Review activities: (Project 5945-2011-043) Air Force - 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
