1、AMSC N/A FSC 5950 INCH-POUND MIL-T-27/185B 9 November 2009 SUPERSEDING MIL-T-27/185A 8 April 1992 MILITARY SPECIFICATION SHEET TRANSFORMER (CHOPPER INPUT) This specification is approved for use by all Depart- ments and Agencies of the Department of Defense. The requirements for acquiring the transfo
2、rmer described herein shall consist of this specification sheet and MIL-PRF-27. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Marking shall be on the side of the case. FIGURE 1. Dimensions and configurations 4 5 .313 .0153 2 1 2.5 k 0 2.5 k 10 k
3、 T C 12345761.125 .016SQ.1.375 .031SQ.128 .005 DIA 4 HOLESTERMINAL EQUALLYSPACED ON A.625 .015 DIA.7 REQD1.375 DIA. MAX.1.625 + .125 - .063.109 .015 R 10 k 1.6 mW 60 Hz , 60mW 400 Hz WV 175 PK ALTITUDE: 50,000 FT. MAX. 6 7 50 k CIRCUIT DIAGRAM AND MARKING Inactive for new design after 25 August 1998
4、 Inches mm .005 0.13 .015 0.38 .016 0.41 .031 0.79 .063 1.60 .109 2.77 .125 3.18 .128 3.25 .313 7.95 .625 15.88 1.125 28.58 1.375 34.92 1.625 41.28Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-27/185B 2 REQUIREMENTS: (When numbers in parenthe
5、ses, such as (1-3) are used, they indicate the winding and the extreme terminals of the winding.) Electrical ratings: See table I. Primary inductance: 200/50 Henrys ct, minimum at 1 volt, 60 Hz. Primary level: 60 milliwatts at 400 Hz and 1.6 milliwatts at 60 Hz. Primary impedance: (1-2-3): 10 K ohms
6、 ct. (3-4-5): 10 K ohms ct. (2-3-5): 10 K ohms ct. Secondary impedance (6-7): 50 K ohms. Primary resistance: 1,300/650 ct ohms 25 percent. Secondary resistance: 1,900 ohms 25 percent. Working voltage: 175 volts peak (1-2). Frequency range: 60 to 400 hertz. Design and construction: Dimensions and con
7、figuration: See figure 1. Duty cycle: Continuous. Case: Metal encased, hermetically sealed. Material: Cold-rolled steel. Terminals: Solder lug, glass-to-metal seal. Height: .313 .015 inch (7.95 0.38 mm). Weight: 4 ounces. Terminal strength: MIL-STD-202, method 211, test condition A, 5.0 pounds. Diel
8、ectric withstanding voltage: At sea level: 500 volts rms. At reduced barometric pressure: 300 volts rms. Electrical characteristics: No load (centertap voltage unbalance only): With 10 volts, 60 hertz and 0 amperes dc applied to (1-5), unbalance (3-5) and (3-1), 1 percent maximum. Polarity: Additive
9、, with terminals 5 and 7 connected. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-27/185B 3 Electrostatic shielding: Voltage ratio 5:1 at 20 kHz. Marking location: See figure 1. Part or Identification Number (PIN): M27/185-01. Changes from pr
10、evious issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are caut
11、ioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-PRF-27, this document references the following: MIL-STD-202 Custodians: Preparing activity: Arm
12、y - CR DLA - CC Navy - EC Air Force - 85 (Project 5950-2009-011) DLA - CC Review activities: Army - AR, CR4 Navy - AS, MC, OS Air Force - 19, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
