1、 MS24591D INCH-POUND14 May 2007 SUPERSEDING MS24591C 22 September 2000 DETAIL SPECIFICATION SHEET SOCKET, ADAPTER, HOSE TO TUBE, REUSABLE, HYDRAULIC, FUEL AND OIL LINES, 1 THROUGH 2 INCHES TUBING SIZES This specification is approved for use by all Departments and Agencies of the Department of Defens
2、e. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5070. Inches mm .0156 .0469 0.396 1.191 FIGURE 1. Socket dimensions and configuration. AMSC N/A FSC 4730 Provided by IHSNot for ResaleNo reproduction or networking permitted without l
3、icense from IHS-,-,-MS24591D 2 ENLARGED VIEW OF THREAD X DETAIL C Dash number A inches (mm) B inches (mm) C inches (mm) D inches (mm) E inches (mm) F inches (mm) G inches (mm) H inches (mm) J inches (mm) -16 1.671 (42.44) 1.651 (41.94) 1.546 (39.27) 1.516 (38.51) 1.421 (36.09) 1.391 (35.33) 1.453 (3
4、6.91) 1.423 (36.14) 1.015 (25.78) 1.002 (25.45) 1.280 (32.51) 1.260 (32.00) 1.290 (32.77) 1.175 (29.85) 1.340 (34.04) 1.330 (33.78) -20 1.760 (44.70) 1.740 (44.20) 1.921 (48.79) 1.891 (48.03) 1.765 (44.83) 1.735 (44.07) 1.765 (44.83) 1.735 (44.07) 1.265 (32.13) 1.252 (31.80) 1.373 (34.87) 1.353 (34.
5、37) 1.555 (39.50) 1.430 (36.32) 1.560 (39.62) 1.550 (39.37) -24 1.860 (47.24) 1.830 (46.48) 2.124 (53.95) 2.094 (53.19) 1.937 (49.20) 1.907 (48.44) 1.953 (49.61) 1.923 (48.84) 1.515 (38.48) 1.502 (38.15) 1.465 (37.21) 1.445 (36.70) 1.800 (45.72) 1.675 (42.55) 1.810 (45.97) 1.795 (45.59) -32 2.270 (5
6、7.66) 2.230 (56.64) 2.640 (67.06) 2.600 (66.04) 2.460 (62.48) 2.420 (61.47) 2.460 (62.48) 2.420 (61.47) 1.948 (49.48) 1.940 (49.28) 1.860 (47.24) 1.820 (46.23) 2.290 (58.17) 2.160 (54.86) 2.330 (59.18) 2.315 (58.80) FIGURE 1. Socket dimensions and configuration - Continued. Provided by IHSNot for Re
7、saleNo reproduction or networking permitted without license from IHS-,-,-MS24591D 3 K L P Q S T U Dash number inches (mm) inches (mm) M N inches (mm) inches (mm) inches (mm) inches (mm) inches (mm) -16 .300 (7.62) .280 (7.11) .270 (6.86) .046 (1.17) .016 (.41) .0575 (1.46) -20 .350 (8.89) .255 (6.48
8、) .245 (6.22) 20 15 -24 .000 .455 (11.56) .445 (11.30) 8 25 .062 (1.57) .032 (.81) .077 (1.96) .047 (1.19) .0625 (1.59) .166 (4.22) .000 (.00) -32 .250 (6.35) .520 (13.21) .480 (12.19) 12.5 15 .070 (1.78) .030 (.76) .050 (1.27) .010 (.25) .0620 (1.57) .200 (5.08) .022 (.56) .012 (.30) Dash number V
9、inches (mm) W X LH-Round thread (see note 7) Y (see note 7) PD Z inches(mm) -16 3.5 1.290-6 1.0625-18 UNEF-2B - .109 (2.77) .079 (2.01) -20 4 1.555-6 1.3125-18 UNEF-2B - .140 (3.56) .110 (2.79) -24 .031 (0.79) 1.800-6 1.5625-18 UNEF-2B - .156 (3.96) -32 .018 (0.46) 4.5 2.285-5 2.0000-18 UNS-2B 1.970
10、6 1.9639 .180 (4.57) .140 (3.56) NOTES: 1. Dimensions are in inches 2. Metric equivalents are for information only. 3. Thread marks on diameter G shall not be cause for rejection. 4. Unless otherwise specified, tolerances are as follows: angles 1, decimals .005 inch (0.13 mm). 5. Break all sharp edg
11、es and remove all burrs and slivers. 6. Unless otherwise specified, maximum surface roughness shall be 125 in Rain accordance with ASME B46.1. 7. Except round threads, threads shall be in accordance with MIL-S-7742. 8. Part or Identifying Number (PIN). FIGURE 1. Socket dimensions and configuration -
12、 Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24591D 4 REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-5070 and figure 1 in case of conflict between th
13、is drawing and MIL-DTL-5070, this drawing shall govern. Intended use. This part is a component of MS24587, MS27224, MS27226, MS27228, MS27230, and MS27232. Material: Aluminum in accordance with MIL-DTL-5070. Finish: Finish shall be in accordance with MIL-DTL-5070. Color identification: Color identif
14、ication shall be in accordance with MIL-DTL-5070. PIN example: MS 24591 -16 AAMaterial/finish code, see table I Dash number on figure 1 Specification number MS prefix TABLE I. Code for material and finish. Code Dash size Material/finish AA -16 through -32 Aluminum anodic coating Marking: The PIN and
15、 the manufacturers Commercial and Government Entity (CAGE) Code or trademark shall be marked on the socket or a removable tag securely attached to the socket. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue, due to
16、the extent of the changes. Referenced documents. In addition to MIL-DTL-5070, this document references the following: MIL-S-7742 MS24587 MS27224 MS27226 MS27228 MS27230 MS27232 ASME B46.1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS24591D 5 CON
17、CLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - AS Air Force - 99 (Project 4730-2005-041) DLA - CC Review activities: Army - AV Navy - MC, SA Air Force - 11, 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
