1、 MS27626B 22 October 2009 SUPERSEDING MS27626A 29 September 2000 DETAIL SPECIFICATION SHEET NIPPLE, FLARED, TUBE TO HOSE-SWIVEL NUT This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall c
2、onsist of this specification sheet and MIL-DTL-83296. FIGURE 1. Nipple, flared, dimensions and configuration. AMSC N/A FSC 4730 INCH-POUND Inch mm .005 .010 .020 0.13 0.25 0.51 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27626B 2 Part or Identi
3、fying Number (PIN) A .010 (0.25) inch (mm) B .005 (0.13) inch (mm) C inch (mm) D .005 (0.13) inch (mm) E .005 (0.13) inch (mm) F .005 (0.13) inch (mm) G .005 (0.13) inch (mm) MS27626-4C .428 (10.87) .929 (23.60) .750 (19.05) .379 (9.63) .110 (2.79) .544 (13.82) .041 (1.04) MS27626-6C .545 (13.84) .9
4、81 (24.92) .875 (22.23) .361 (9.17) .085 (2.16) .660 (16.76) .043 (1.09) MS27626-8C .630 (16.00) 1.137 (28.88) 1.000 (25.40) .400 (10.16) .100 (2.54) .813 (20.65) - MS27626-10C .735 (18.67) 1.388 (35.26) 1.250 (31.75) .338 (8.59) .100 (2.54) .989 (25.12) .037 (.94) FIGURE 1. Nipple, flared, dimensio
5、ns and configuration - Continued. Inch mm .005 .010 .020 .025 0.13 0.25 0.51 0.66 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27626B 3 PIN H .050 (1.27) inch (mm) J +.000 -.005 (-0.13) inch (mm) K .005 (0.13) inch (mm) L .005 (0.13) inch (mm) M
6、 .010 (0.25) inch (mm) N .005 (0.13) inch (mm) P .02 inch (mm) MS27626-4C .100 (2.54) .250 (6.35) .420 (10.67) - - - .72 (18.29) MS27626-6C .343 (8.71) .495 (12.57) - - - .84 (21.34) MS27626-8C .445 (11.30) .610 (15.49) - .783 (19.89) .030 (0.76) .97 (24.64) MS27626-10C .588 (14.94) .762 (19.35) .15
7、0 (3.81) - - 1.22 (30.99) PIN R .5 S .005 (0.13) inch (mm) Thread T Pitch diameter inch (mm) U 5 MS27626-4C - .161 (4.09) .625-18UNJF-3A .5889/.5854 (14.958/14.869) 45 MS27626-6C - .271 (6.88) .750-16UNJF-3A .7094/.7056 (18.189/17.922) MS27626-8C - .375 (9.53) .875-24UNJS-3A .8479/.8448 (21.537/21.4
8、58) 30 MS27626-10C 10 .465 (11.81) 1.0625-20UNJ-3A 1.0300/1.0266 (26.162/26.076) 45 PIN V .005 (0.13) inch (mm) W .005 (0.13) inch (mm) AA .005 (0.13) inch (mm) AB inch (mm) AC .005 (0.13) inch (mm) MS27626-4C - .825 (20.96) .069 (1.75) .625 (15.88) +.000 -.009 (+.000 -0.23) .138 (3.51) MS27626-6C -
9、 .962 (24.43) .092 (2.34) .750 (19.05) .185 (4.70) MS27626-8C .050 (1.27) 1.100 (27.94) .095 (2.41) .875 (22.23) +.000 -.007 (+.000 -0.18) .190 (4.83) MS27626-10C - 1.375 (34.93) .125 (3.18) 1.062 (26.97) +.000 -.008 (+.000 -0.20) .250 (6.35) FIGURE 1. Nipple, flared, dimensions and configuration -
10、Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27626B 4 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for information only. 3. Unless otherwise specified, tolerances for three place decimals are .005 inch (0.13 mm)
11、. 4. Radius or break all corners to .005 +.005/-.000, unless otherwise specified. 5. Surface roughness, in accordance with ASME B46.1, shall not exceed 125 in Ra, unless otherwise specified. 6. In area X, a solid-film lubricant shall be used as specified in MIL-PRF-46010 or SAE-AS5272. Solid-film lu
12、bricant shall be allowed in area Y. Solid-film lubricant shall not extend beyond area Z. 7. For dimension C, use commercial stock size tolerances as specified in SAE-AMS2241. 8. Dimensioning and tolerancing are in accordance with ASME Y14.5M. 9. All burrs and slivers shall be removed. FIGURE 1. Flar
13、ed, nipple dimensions and configuration - Continued. REQUIREMENTS: Dimensions and configurations: The design, construction, and physical dimensions shall be in accordance with MIL-DTL-83296 and figure 1, in case of conflict between this specification sheet and MIL-DTL-83296, this specification sheet
14、 shall govern. This is a design specification sheet for manufacturing purposes. The item is only procured as an integral part of adapter assembly MS27619. This part is for use with MIL-DTL-83298 hose and hose assemblies in accordance with MIL-DTL-32330. Material: Material shall be corrosion resistan
15、t steel (CRES), class 304, condition B (accepted classes only), as specified in ASTM A276 or ASTM A473, with minimum yield of 70,000 psi (483 MPa) for sizes -4C, -6C, and -8C and a minimum yield of 60,000 psi (552 MPa) for size -10C. Finish: Finish shall be passivated in accordance with MIL-DTL-8329
16、6. PIN example: MS27626 -4 C PIN example: MS27626-4C indicates a nipple 1/4 inch, CRES. Specification sheet number Dash size (see figure 1) Material (C for CRES) MS prefix Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS27626B 5 Changes from previo
17、us issue. Marginal notations are not used in this revision to identify changes due to the extent of the changes. Referenced documents. In addition to MIL-DTL-83296, this document references the following: MIL-DTL-83298 MIL-DTL-32330 MIL-PRF-46010 MS27619 ASME B46.1 ASME Y14.5M ASTM A276 ASTM A473 SA
18、E-AMS2241 SAE-AS4395 SAE-AS5272 SAE-AS8879 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AV DLA - CC Navy - AS Air Force - 99 (Project 4730-2008-044) DLA - CC Review activities: Navy - MC, SA Air Force - 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
