1、AMSC N/A FSC 5930 INCH-POUND MS39061D 21 December 2004 SUPERSEDING MS39061C w/Amendment 2 24 March 2004 DETAIL SPECIFICATION SHEET SWITCH, TOGGLE, SPST, AND SPDT, 24 VOLT DC, 25 AMPERE (WATERPROOF) This specification is approved for use by all Departments and Agencies of the Department of Defense. T
2、he complete requirements for acquiring the switch described herein shall consist of this specification and the latest issue of MIL-DTL-13735. Configuration A FIGURE 1. Dimensions and configuration. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39
3、061D 2 Inches mm Inches mm Inches mm Inches mm .016 0.41 .40 10.2 .75 19.1 1.625 41.28 .060 1.52 .625 15.88 .875 22.23 1.813 46.05 .188 4.76 .719 18.26 .969 24.61 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, toleranc
4、e is .030 (0.79 mm) on decimals and .5 on angles. 4. Switch shall withstand a force of 25 pounds applied .125 .031 inch from the end of the switch lever. and the lever dimensions shall be such as to allow for incorporation of the luminous shown on USAF DWG 43A17587. 5. Waterproof boot for switch lev
5、er shall meet the environmental requirements of MIL-DTL-13735. 6. Contour of switch optional provided maximum dimensions specified are not exceeded. 7. Marking shall consist of the PIN and Manufacturers Identification in accordance with MIL-STD-130 and lever position identification in accordance wit
6、h figure 1, configuration A. FIGURE 1. Dimensions and configurations - continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39061D 3 Configuration B (Grade 1, Type I and II). Inches mm Inches mm Inches mm Inches mm .015 .381 .28 7.112 .75 19.
7、05 1.812 46.025 .03 .762 .40 10.16 1.28 32.512 2.15 54.61 .032 .813 .50 12.70 1.50 38.10 7.50 190.50 .06 1.524 .634 16.104 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, tolerance is .030 (0.79 mm) on decimals and 10 o
8、n angles. 4. Mounting plate shall be rigidly and firmly assembled to the switch as shown. 5. Switch shall withstand a force of 25 pounds applied .125 .031 inch from the end of the switch lever. 6. The lever dimensions shall be such as to allow for incorporation of the luminous shown on figure 2. 7.
9、Contour of switch optional provided maximum dimensions specified are not exceeded. 8. All exposed switch terminals shall be encapsulated with potting material. Presence of thin traces of potting material on switch base allowed. 9. All wire leads shall be supplied with connectors in accordance with M
10、S27142-2 or equivalent. 10. Lead wires shall be 14 AWG, M13486/1-5 in accordance with MIL-DTL-13486, color black. Each lead wire shall be marked with numerals 1 through 3. Non-functional lead wires shall not be supplied. 11. At minimum, marking shall consist of the PIN and Manufacturers Identificati
11、on in accordance with MIL-STD-130 and lever position identification in. FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39061D 4 Configuration C (Grade 1, Type III and IV). Inches mm Inches mm In
12、ches mm Inches mm .015 .381 .28 7.112 .940 23.88 1.812 46.025 .03 .762 .40 10.16 1.35 34.29 2.15 54.61 .032 .813 .50 12.70 1.50 38.10 7.50 190.50 .06 1.524 .75 19.05 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Unless otherwise specified, toler
13、ance is .030 (0.79 mm) on decimals and 10 on angles. 4. Mounting plate shall be rigidly and firmly assembled to the switch as shown. 5. Switch shall withstand a force of 25 pounds applied .125 .031 inch from the end of the switch lever. 6. The lever dimensions shall be such as to allow for incorpora
14、tion of the luminous shown on figure 2. 7. Contour of switch optional provided maximum dimensions specified are not exceeded. 8. All exposed switch terminals shall be encapsulated with potting material. Presence of thin traces of potting material on switch base allowed. 9 All wire leads shall be sup
15、plied with connectors in accordance with MS27142-2 or equivalent. 10. Lead wires shall be 14 AWG, M13486/1-5 in accordance with MIL-DTL-13486, color black. Each lead wire shall be marked with numerals 1 through 3. Non-functional lead wires shall not be supplied. 11. Marking shall consist of the PIN
16、and Manufacturers Identification in accordance with MIL-STD-130 and lever position identification. FIGURE 1. Dimensions and configurations - continued. 7 9 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39061D 5 FIGURE 2. Luminous dimensions RE
17、QUIREMENTS: Dimension and configuration: See figure 1. Terminals: Configuration A: MS33800 or equivalent. Wire leads (when applicable), shall be 16 AWG, M13486/1-3 in accordance with MIL-DTL-13486, color black. Each lead wire shall be marked with numerals 1 through 3. Non-functional lead wires shall
18、 not be supplied. Configuration B or C: MS27142-2 or equivalent. Wire leads (when applicable), shall be 14 AWG, M13486/1-5 in accordance with MIL-DTL-13486, color black. Each lead wire shall be marked with numerals 1 through 3. Non-functional lead wires shall not be supplied. Switching characteristi
19、cs: See table II. Direction of movement of internal mechanism is opposite to the direction of the toggle movement. Sealing: The switches shall be immersed in an enclosure containing water. The enclosure shall be subjected to a vacuum resulting in an absolute pressure equal to 2.0 0.5 inches of mercu
20、ry for 5 minutes. The immersed switches shall be observed for leakage as evidenced by a continuous stream of bubbles emanating from the water prior to release of the vacuum. Electrical ratings: See table I. Contact voltage drop: Shall not exceed 50 millivolts when tested using load of 100 milliamper
21、es at 2-6 volts dc. Switch contacts shall be actuated 3 times prior to taking the final measurement. Part or Identifying Number (PIN): See table II. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39061D 6 TABLE I. Electrical ratings, configuration
22、s A, B, and C. Configuration A Configuration B Configuration C 24 V dc 24 V dc 24 V dc Load (amperes) (amperes) (amperes) Resistive 25 25 25 Inductive 15 15 15 Lamp 6 6 6 TABLE II. Switching characteristics and PINs for configuration A. MIL-DTL-13735Configuration1/ Circuit with toggle lever in posit
23、ion PIN Former GovernmentDesignation Type Class A B Center C MS39061-1 8376806 I B A or B On (12) None Off MS39061-2 8376807 I A A or B Mom. On (12) None Off MS39061-3 8376808 I AB A or B On (12) None Mom. off MS39061-4 8376809 II B A or B On (23) Off On (13) MS39061-5 8376810 I AB A or B On (23) No
24、ne Mom. On (13)MS39061-6 8376811 II AB A or B On (23) Off Mom. On (13)MS39061-7 8376812 I AB A or B On (23) None On (13) MS39061-8 8376813 II A A or B Mom. On (23) Off Mom. On (13)MS39061-9 7954899 III B C On (13) None Off MS39061-10 7954900 IV B C On (13 Off On (23) MS39061-11 7954901 IV AB C Mom.
25、On (13) None On (23) MS39061-12 7954902 IV AB C Mom. On (13) Off On (23) MS39061-13 7954903 IV B C On (13) None On (23) MS39061-14 7954904 III A C Mom. On (13) None Off MS39061-15 7954905 IV A C Mom. On (13) Off Mom. On (2-3)MS39061-16 7954906 III AB C On (1)3 None Mom. off 1/ Configurations A and B
26、 are functionally interchangeable. 2/ Configuration C is functionally interchangeable with multi-pole, grade 1, toggle switches per former Ordnance Corps drawing 7954899 through 7954906. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS39061D 7 Chan
27、ges from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Referenced Documents MIL-DTL-13486 MIL-DTL-13486/1 MIL-DTL-13735 MIL-STD-130 MS33800D MS27142 USAF DWG 43A17587 Custodians: Preparing act
28、ivity: Army - AT DLA - CC DLA - CC (Project 5930-1877) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
