1、 DETAIL SPECIFICATION SHEET CAP, FUEL TANK: COMBAT VEHICLES, SPILLPROOF Inactive for new design after 22 January 1999. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of thi
2、s specification sheet. FIGURE 1. Cap, fuel tank: combat vehicle, spillproof. ASMC N/A FSC 2910 INCH-POUND MS51300F 09 May 2011 SUPERSEDING MS51300E(AT) 13 June 1990 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS51300F 2 Inches mm Inches mm Inches
3、 mm Inches mm 0.016 0.41 0.250 6.35 2.500 63.50 4.625 117.48 0.030 0.76 0.500 12.70 3.120 79.25 7.000 177.80 .0.031 0.79 0.530 13.46 3.500 88.90 0.125 3.18 .0.750 19.05 3.797 96.444 0.130 3.30 2.020 51.31 4.500 114.30 NOTES: 1. Dimensions are in inches. Tolerances are .010 on decimals, 1 on angles.
4、2. Metric equivalents are given for information only. 3. All dimensions are “reference” dimensions. 4. For design feature purposes, this standard takes precedence over acquisition documents referenced herein. FIGURE 1. Cap, fuel tank: combat vehicle, spillproof Continued. REQUIREMENTS This cap is of
5、 procurement specification MIL-C-45300, Type I. This cap is to be used with necks shown on MS35644. Material: Retainer: Steel 1065, 1074, or 1085 as specified in ASTM-A684/A684M. After forming, retainer shall be annealed and tempered to Rockwell 40-55 C. The chain shall conform to RR-C-271, Type II,
6、 Class 6. Protective coating: Interior parts shall be zinc plated as specified in ASTM-B633 Type VI, Fe/Zn 5. The cover and other exterior parts shall be phosphate coated as specified in MIL-DTL-16232, type Z (zinc phosphate base), Class I. In the event of a conflict between the text of this standar
7、d and the references cited herein. The text of this standard shall take precedence. This standard is not intended to limit construction to features other than shown herein by dimensions, notations and referenced documents. Part or Identifying Number (PIN). Example of a PIN: MS51300-1 (base number) E
8、xample of a PIN: MS51300-1 Type of guide and neck (see figure 1) MS prefix and basic number Marking shall consist of the PIN and manufacturers identification in accordance with MIL-STD-130. Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect
9、 to the previous issue due to the extent of the changes. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS51300F 3 Referenced documents. This document references the following: MIL-STD-130 MIL-C-45300 MIL-DTL-16232 MS35644 RR-C-271 ASTM-A684/A684M A
10、STM-B633 CONCLUDING MATERIAL Custodians: Preparing activity: Army AT DLA CC Navy MC Air Force 99 (Project 2910-2010-006) DLA CC Review activities: Army CR4 Navy SA, YD Air Force 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
