1、QQ-W-4L4B 95 9997974 O009660 4 . B, tinned; C, liquor finished; D, zinc coated. 3.7 Type I, flat steel wire. The type I, flat steel wire shall conform to the Stand- ards Manual of the Fine and Specialty Wire Manufacturers Association, volume II. Size shall be as specified (see 6.2), and shall be as
2、shown in table II. Tolerance on thick- ness shall be plus or minus 0.0005 innch. Size No. 18 by 20 19 by 21 20 by 22 20 by 23 20 by 24 20 by 25 21 by 25 22 by 26 23 by 30 19 by 21-1/2 Width (inch) 0.0475 .O410 .O410 .O348 .O348 .O348 .O348 .O317 .O286 .O258 TABLE II. F1; Tolerance on widths, minus (
3、inch) O, 0004 .O004 .0.004 .O004 .O004 .O004 .O004 .O003 .O003 .O003 ; Wire Thickness (inch) O. 0348 .O317 .O301 .O286 ,0258 .O230 ,0204 .O204 .O181 .O140 Approximate length per pound (feet) 206 290 305 3 50 415 47 8 525 644 7 50 248 3.8 Tvae II. round steel wire. The tvue II round steel wire shall
4、conform to the Standards-Manual of the Fine and Specialti Vire lanuf acturers Association. as specified (see 6.2), and shall be as shown in table III. Size shall be TABLE III, Round wire U.S. steel wire gage No. 17 18 19 20 21 22 23 24 25 g 28 30 Diameter (inch) O. 0540 .O475 .O410 .O348 .O317 .O286
5、 .O258 .O230 -0204 .O181 .O173 .O162 .O140 Tolerance on di amet er (inch) plus or minus O. 0015 ,0015 ,0015 .O015 . O010 . O010 ,0010 . O010 . O010 .O007 .O007 .O007 .O007 Approximate length per pound (feet) 129 169 226 3 27 37 O 485 608 713 903 1.172 1.320 1.483 1.940 3.9 Workmanship. The finished,
6、 coated wire shall be smooth and free from kinks, waviness, bare or imperfectly coated spots, scratches, or other defects that will affect its use. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or pur- chase order, the supplier is respo
7、nsible for the performance of all inspection require- ments as specified herein, Except as otherwise specified, the supplier may utilize his own facilities or any commercial laboratory acceptable to the Government. The Government reserves the right to perform any of the inspections set forth in the
8、specification where such inspections are deemed necessary to assure that supplies and services conform to pre- scribed requirements. 4.2 Classification of inspection. Inspection shall be classified as follows: (a) Quality conformance inspection (see 4.3). (b) Inspection of preparation for delivery (
9、see 4.5). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-QQ-ii-414b 4.3 Quality confosmance inspection. 4.3.1 Unit of product. Por the purpose of inspection, a unit of product sIial1,be one 4.3.2 SaniplinK. spool or core of wise, 4.3.2.1 Foroxnrii
10、iotion. Saiiipliiig for examination shall be in accordance with I.IIL-STD-105, inspection level 9-3. 4.3.2.2 For tests. Saniples of wire 12 inches in length shall of 12 or le& spoolz or cores. terniediate units in tiie lot, 4.3.3 Examinatioq. Samples selected in accordaiice with 4.3.2 the defects sp
11、ecified in 4.4.1. AQL sliall be 6.5 percent defect The samples sliall be taken near be provided for each lot he first, last, and in- 1 shall be examined for ve. 4.3.4 Tefits. Saniples selected in accordailce mith 4.3.2.2 sha 1 be tested as specified 4.4 Inspection psocedure. in 4.4.2. Failure of the
12、 tests shall be cause for rejection of the lot repimsonted. 4.4.1 Exnniinntion. The spool or COPO of wire shall lie exaniiiied for the folloviiiig defects: - 101 1 102 I 103 I 104. 105. 106. 107. 108 I 100 I 110 I 111 iiire not uniform in finish. Spools or cores not as specified. Vire not in one con
13、tinuous length. Vire not uniformly mound on spools os coros. Viire ends not properly secured to prevent uiiwiiiding. Cores do not .fit speciiied ref illeblo spools Bpindle lioh not correct size. Identification marking incorrect, illegible, or missing. Decimal dimension of type I f lnt ivire incorrec
14、t. Docinial diinension of type II roun wire incorrect. Workoinnahip not as specifie. 4.4.2 B. Ductility ancl tensile tests shall be conducted in accordance with tho standards manual, volume 11, as applicable. Nonconformance to the applicable standards nanual cgihall constitute failwe of these tests.
15、 4.5 Inspection of preparation for delivery. 4. &,I Quality - conforinance inspection of pack. 4.5.1.1 Unit of wsduct. For the purpose o inspection, B completed pack of wire pre- 4.5. I. 2 c Sampling. 4. fi. 1.3 Exruiiination. Saidplos selected in accordance with 4.5.1.2 shall be sxaiiiiiiod for tho
16、 Sollswihg deiects SQL siiall bo 2.5 percent defective. 112. Materials, nietiiods, aiid containers not as specified for level A. Each incorrect sinterial, method, oz container shall constitute one defect. 113. iioight of contente exceed weight limit of sliipping container for level A. 114. Strapping
17、 nut .zinc coated for level A. 115, Marking inconiplete, incorrect, or illegible. pareci for sripmsnt -hbe consicioreci a unit of prsciuct. anipUiig for exariiinatioii siiall bo in accorclanco with .IL-STD-lOB. Ei. PREPARATION JOB DELIVERY 5.1 Preservation and pnclrnging. Preservation and packaging
18、shall be level A or C, as specified (see 6,2) 5.1.1 Level. A. Each core or spool of wire shall be preserved and packaged in accord- ance viitli ?lILP-116, method III. The unit container shall conform to PPP-J3-636, type CF, clnss ieatIier-resio:tant, and shall be closed in accordailce wit11 the appe
19、ndix to the box cpecif ication. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-QQ-W-LILLIO 75 W 7777774 0007bbli L QQ-W-414b 5.1.2 Level C. Each core or spool of wire shall be packaged in a commercial con- tainer which will provide adequate protecti
20、on against deterioration and damage from the supplier to the first receiving activity. 5.2 Packing. Packing shall be level A, B, or C, as specified (see 6.2). 5.2.1 Level A. The cores or spools of wire of like description, packaged as speci- fied in 5.1, shall be packed in snug-fitting boxes conform
21、ing to PPP-B-621, class 2, style optional, or PPP-B-601, overseas type, style optional. The gross weight of the boxes shall not exceed 200 pounds and the boxes shall be closed and strapped in accord- ance with the appendix to the applicable box specification. Strapping shall be zinc coated. 5.2.2 Le
22、vel B. The wire, packaged as specified in 5.1, shall be packed in boxes conforming to PPP-B-636, class weather-resistant, grade V3c. Closure and strapping of the boxes shall be in accordance with the a.ppendix to the box specification. tities specified (see 6,2), to assure carrier acceptance and saf
23、e delivery to destina- tion at lowest rates in containers complying with Uniform Freight Classification Rules or National Motor Freight Classification Rules. 5.2.3 Level C. The wire, packaged as specified in 5.1, shall be packed in the quan- 5.3 Marking. 5.3.1 Civil agencies. In addition to any spec
24、ial markings specified in the contract or order, Fackages and shipping containers shall be marked in accordance with Fed. Std. No. 123. tract or order, the interior packages and shipping containers shall be marked in accordance with MIL-STD-129. 5.3.2 Military agencies. In addition to any special ma
25、rkings specified in the con- 6. NOTES 6.1 Intended use. 6.2 Ordering data. The bookbinder steel wire is intended for use in manually- operated or automatically-operated bookbinding and paper stitching machines. and include the following information in procurement documents: a Title, number, and date
26、 of this e ecification. b c Purchasers should select the preferred options permitted herein Type and finish required (see 1.27. Whether spools or paper cores shall be furnished (see 3.1). Diameter of spool spindle hole if other than as specified (see 3.3). Type and size of refillable spool required
27、(see 3.4). Quantity of refillable spools required (see 3.4). Size of flat steel wire required (see 3.7 . Size of round steel wire required (see 3. 8 ). 21 - Selection of applicable levels of preservation, packaging, and packing (A) Quantity to be packed (see 5.2.3) e required (see 5.1 and 5.2). 6.3
28、This specification covers only the types, sizes, and finishes of the commodity as generally purchased by the Federal Government and is not intended to include ail. the types, sizes, and finishes which are commercially available. MILITARY INTEREST: User activity: Preparing activity: Custodians: Army
29、- MR Army - ME Army - ME CIVIL AGENCIES: Code “N“ Air Force - 69 GSA, HEN, VA, JUS, NBS, NSA Other: Review activities: IS Air Force - 69 U. S. Government Printing Office - i967 Orders for this publication are to be placed with General Services Administration, a.cting as an agent for the Superintende
30、nt of Documents. cation to obtain extra copies and other documents referenced herein. pr-ice 5 cents each. each. See section 2 of this specifi- 5 t U. S. GOVERNAENT PRXTIliG OFFICE : 1967 O - 302-502 (2.55) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
