1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Correct propagation delay minimum limit in table I. jak 00-08-22 Monica L. Poelking B Make change to footnote 9/ in table I. Add vendor CAGE F8859. Add case outline X. Add device type 02. Add table III, delta limits. Change PRR in note 3 on figur
2、e 4. Update drawing to MIL-PRF-38535 requirements. Editorial changes throughout. jak 03-04-09 Thomas M. Hess C Update boilerplate paragraphs to the current MIL-PRF-38535 requirements. - LTG 09-10-23 Thomas M. Hess REV SHET REV SHET REV STATUS REV C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6
3、 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Joseph A. Kerby DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Charles F. Saffle, Jr. APPRO
4、VED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ADVANCED CMOS, DUAL 4-INPUT NAND GATE, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON DRAWING APPROVAL DATE 00-03-15 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-00513 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E036-10 Provided by IHSNot for ResaleN
5、o reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00513 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels co
6、nsisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the
7、 PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 00513 01 Q C A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device class
8、es Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA d
9、evice. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ACT20 Dual 4-input NAND gate, TTL compatible inputs 02 54ACT20 Dual 4-input NAND gate, TTL compatible inputs 1.2.3 Device class designator. The device class desi
10、gnator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certificatio
11、n and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line X CDFP3-F14 14 Flat pack 1.2.5 Lead finish. The lead finish is as s
12、pecified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00513 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-
13、3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +6.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+ 0.5 V dc DC output voltage range (VOUT) . -0.5 V dc to VCC+ 0.5 V dc DC input clamp current (IIK) (VINVCC+ 0.5 V
14、) 20 mA DC output clamp current (IOK) (VOUTVCC + 0.5 V) . 50 mA DC output source or sink current per output pin (IOUT) . 50 mA DC VCCor ground current (ICCor IGND) . 100 mA Storage temperature range (TSTG) . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to
15、-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +150C Maximum power dissipation (PD) . 500 mW 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT) . +0.0 V dc to VCCMinimum high lev
16、el input voltage (VIH) . +2.0 V Maximum low level input voltage (VIL) +0.8 V Maximum high level output current (IOH) -24.0 mA Maximum low level output current (IOL) +24.0 mA Maximum input rise or fall rate (t/V) . 10 ns/V Case operating temperature range (TC) -55C to +125C 1/ Stresses above the abso
17、lute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the fully specified
18、 VCCrange and case temperature range of -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00513 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 AP
19、R 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or cont
20、ract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDB
21、OOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 1911
22、1-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents cited in the solicitation or contract. ELECTRONIC INDUSTRIES ALLIANCE (EIA) JEDEC Standard No. 20 - Standard for
23、Description of 54/74ACXXXXX and 54/74ACTXXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http:/www.jedec.org or from Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834). 2.3 Order of precedence. In the event of a conflict between
24、 the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements f
25、or device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for d
26、evice class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q a
27、nd V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure
28、 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN
29、DARD MICROCIRCUIT DRAWING SIZE A 5962-00513 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance character
30、istics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined
31、in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on
32、the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certificat
33、ion mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QM
34、L-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of co
35、mpliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
36、 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For devi
37、ce class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the opti
38、on to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group nu
39、mber 36 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00513 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I.
40、Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Device type and device class 3/ VCCGroup A subgroups Limits 4/ Unit Min Max Positive input clamp voltage 3022 VIC+For input under test IIN=
41、 1.0 mA All V 0.0 V 1 0.4 1.5 V Negative input clamp voltage 3022 VIC-For input under test IIN= -1.0 mA All V Open 1 -0.4 -1.5 V High level output voltage 3006 VOH VIN= VIHor VILVIH= 2.0 V and VIL= 0.8 V IOH= -50 A All All 4.5 V 1, 2, 3 4.4 V 02 All 5.5V 5.4 VIN= VIHor VILVIH= 2.0 V and VIL= 0.8 V I
42、OH= -24 mA All All 4.5 V 1 3.94 2, 3 3.7 02 All 5.5 V 1 4.86 2, 3 4.7 VIN= VIHor VILVIH= 2.0 V and VIL= 0.8 V IOH= -50 mA 5/ All All 5.5 V 2, 3 3.85 Low level output voltage 3007 VOL VIN= VIHor VILVIH= 2.0 V and VIL= 0.8 V IOL= +50 A All All 4.5 V 1, 2, 3 0.1 V 02 All 5.5 V 1, 2, 3 0.1 VIN= VIHor VI
43、LVIH= 2.0 V and VIL= 0.8 V IOL= +24 mA All All 4.5 V 1 0.36 2, 3 0.5 02 All 5.5 V 1 0.36 2, 3 0.5 VIN= VIHor VILVIH= 2.0 V and VIL= 0.8 V IOL= +50 mA 5/ All All 5.5 V 2, 3 1.65 Input leakage current high 3010 IIHFor input under test VIN= 5.5 V For all other inputs VIN= VCCor GND All All 5.5 V 1 +0.1
44、 A 2, 3 +1.0 Input leakage current low 3009 IILFor input under test VIN= 0.0 V For all other inputs VIN= VCCor GND All All 5.5 V 1 -0.1 A 2, 3 -1.0 Quiescent supply current delta, TTL input levels 3005 ICC6/ For input under test VIN= VCC- 2.1 V For all other inputs VIN= VCCor GND 01 All 4.5 V and 5.
45、5 V 1 648.0 A 2, 3 810.0 02 All 5.5 V 1, 2, 3 1.6 mA Quiescent supply current 3005 ICCFor all inputs VIN= VCCor GND IOUT= 0.0 V All All 5.5 V 1 4.0 A 2, 3 80.0 Input capacitance 3012 CINSee 4.4.1c TC= +25C All All GND 4 10.0 pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduct
46、ion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00513 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test and MIL-STD-883 test method
47、 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Device type and device class 3/ VCCGroup A subgroups Limits 4/ Unit Min Max Power dissipation capacitance CPD7/ See 4.4.1c TC= +25C, f = 1 MHz All All 5.0 V 4 48.0 pF Functional tests 3014 8/ See 4.4.1b VIN= VIH
48、or VILVIH= 2.0 V and VIL= 0.8 V Verify output VOUTAll All 4.5 V 7, 8 L H 5.5 V 7, 8 L H Propagation delay time, mA, mB, mC, or mD to mY 3003 tPHL, tPLH9/ CL= 50 pF RL= 500 See figure 4 All All 4.5 V 9, 10, 11 1.0 13.5 ns 1/ For tests not listed in the referenced MIL-STD-883 (e.g. ICC), utilize the general test procedure of 883 under the conditions listed herein. 2/ Each input/output, as applicable, shall be tested at the specified temperature, for the specified limits, to the tests in table I herein. Output terminals not designated shall be high-level logic, low-level log
