1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Added case outlines M and N. Figure 3; Made changes to the block diagram for the adjustable device types 06 and 11. -sld 08-07-03 Robert M. Heber REV SHEET REV SHEET REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10
2、11 12 13 14 PMIC N/A PREPARED BY Steve L. Duncan STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil APPROVED BY Robert M. Heber THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFE
3、NSE DRAWING APPROVAL DATE 08-03-04 MICROCIRCUIT, HYBRID, LINEAR, VOLTAGE REGULATOR, 3 A and 5 A OUTPUT CURRENT, LOW DROP OUT AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-06204 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E378-08 Provided by IHSNot for ResaleNo reproduction or networking permitt
4、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06204 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-
5、38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 06204 01 H T
6、 X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified
7、RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 SAT8601-53_T-1.3 Voltage regulator, 5 A, Fixed, +1.3 V output,
8、+3.3 V input 02 SAT8601-53_T-1.5 Voltage regulator, 5 A, Fixed, +1.5 V output, +3.3 V input 03 SAT8601-53_T-1.8 Voltage regulator, 5 A, Fixed, +1.8 V output, +3.3 V input 04 SAT8601-53_T- 2.5 Voltage regulator, 5 A, Fixed, +2.5 V output, +3.3 V input 05 SAT8601-55_T-3.3 Voltage regulator, 5 A, Fixed
9、, +3.3 V output, +5.0 V input 06 SAT8601-33_T-ADJ Voltage regulator, 3 A, Adjustable, +3.3 V input 07 SAT8601-33_T-1.3 Voltage regulator, 3 A, Fixed, +1.3 V output, +3.3 V input 08 SAT8601-33_T-1.5 Voltage regulator, 3 A, Fixed, +1.5 V output, +3.3 V input 09 SAT8601-33_T-1.8 Voltage regulator, 3 A,
10、 Fixed, +1.8 V output, +3.3 V input 10 SAT8601-33_T-2.5 Voltage regulator, 3 A, Fixed, +2.5 V output, +3.3 V input 11 SAT8601-35_T-ADJ Voltage regulator, 3 A, Adjustable, +5 V input 12 SAT8601-35_T-3.3 Voltage regulator, 3 A, Fixed, +3.3 V output, +5.0 V input 13 SAT8605R-53_T-1.3 Voltage regulator,
11、 5 A, Fixed, +1.3 V output, +3.3 V input, Remote sense 14 SAT8605R-53_T-1.5 Voltage regulator, 5 A, Fixed, +1.5 V output, +3.3 V input, Remote sense 15 SAT8605R-53_T-1.8 Voltage regulator, 5 A Fixed, +1.8 V output, +3.3 V input, Remote sense 16 SAT8605R-53_T-2.5 Voltage regulator, 5 A, Fixed, +2.5 V
12、 output, +3.3 V input, Remote sense 17 SAT8605R-55_T-3.3 Voltage regulator, 5 A, Fixed, +3.3 V output, +5.0 V input, Remote sense 18 SAT8605R-55_T-1.3 Voltage regulator, 5 A, Fixed, +1.3 V output, +5.0 V input, Remote sense 19 SAT8605R-55_T-1.5 Voltage regulator, 5 A, Fixed, +1.5 V output, +5.0 V in
13、put, Remote sense 20 SAT8605R-55_T-1.8 Voltage regulator, 5 A, Fixed, +1.8 V output, +5.0 V input, Remote sense 21 SAT8605R-55_T-2.5 Voltage regulator, 5 A, Fixed, +2.5 V output, +5.0 V input, Remote sense 1.2.3 Device class designator. This device class designator shall be a single letter identifyi
14、ng the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest
15、reliability class available. This level is intended for use in space applications. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06204 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL
16、 A SHEET 3 DSCC FORM 2234 APR 97 H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspe
17、ctions with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) tak
18、en to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality lev
19、el is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style T See figure 1 5 MO-078 with
20、straight-leads M See figure 1 5 MO-078 with surface mount-leads N See figure 1 5 MO-078 with right angle lead-bends 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ DC voltage input 10 V Output Current : Device types 01-05 and 13-21 5.5 A De
21、vice types 06-10, 11, and 12 3.5 A Power dissipation (PD) TC= +25C 25 W Thermal resistance, junction-to-case (JC). 3.0C/W Lead temperature (soldering, 10 seconds) +300C Storage temperature range -65C to +150C Case operating temperature range (TC). -55C to +125C 1.4 Recommended operating conditions.
22、Input voltage range: Device types 01-04, 06-10, and 13-16 . +2.9 V to +3.6 V Device types 05, 11, 12, and 17-21 +4.5 V to +5.5 V Output current range: Device types 01-05 and 13-21 .050 A to 5.0 A Device types 06-10, 11, and 12 .050 A to 3.0 A Case operating temperature range (TC) -55C to +125C 2. AP
23、PLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. _ 1/
24、 Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAW
25、ING SIZE A 5962-06204 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Micro
26、circuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quick
27、search/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this doc
28、ument, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534
29、shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as d
30、efined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dime
31、nsions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram. The block diagram shall be as speci
32、fied on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requireme
33、nts shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vend
34、or similar PIN may also be marked. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06204 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 3.6 Data. In ad
35、dition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should in
36、clude a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate
37、 of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A ce
38、rtificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quali
39、ty Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06204 DEFENSE SUPPLY CENTER COLUMBUS C
40、OLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions -55C TC+125C unless otherwise specified Group A subgroups Device type Min Max Unit Output voltage accuracy VOUTVIN= Nominal rated voltage, IOUT= 3.0
41、A 1,2,3 All 2.0 % 01-04, 06-10, 13-16 +2.9 +3.6 Input voltage range 1/ VINIOUT= 3.0 A, TC= +25C 7 05,11, 12,17-21 +4.5 +5.5 V IOUT= 3.0 A, VOUT= 2.5 V, VIN= 2.9 V 3/ 06-10 0.40 IOUT= 5.0 A, VOUT= 2.5 V 01-04, 13-16 0.45 Dropout voltage 2/ VDROP IOUT= 5.0 A, VOUT= 3.3 V 1,2,3 11,12, 17-21 0.45 V 01-0
42、5 13-16 5.5 Current limit ISCVIN= 5.0 V, Over current latch up, TC= +25C 1 06-12 3.5 A Shutdown source current ISHDN VSHDN= 5.0 V, TC= +25C 1 All 200 A Shutdown input voltage 3/ VSHDN VIN= 5.0 V, VOUT2.0 V to initiate output inhibit. Shutdown pin (pin 4) should be grounded if not used. 4/ Not tested
43、, but guaranteed by design. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06204 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Case outline T Inches
44、Millimeters Symbol Min Max Min Max A .240 .270 6.09 6.86 A1 .035 .045 0.89 1.14 A2 .140 BSC 3.55 BSC b .025 .035 0.64 0.89 D .815 .835 20.70 21.21 D1 .530 .550 13.46 13.97 D2 .092 2.37 e .100 BSC 2.54 BSC E .685 .695 17.40 17.65 L .500 .750 12.70 19.05 L1 .697 .707 17.70 17.95 p .155 .165 3.94 4.19
45、NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch- pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. The case outline T is a metal hermetical
46、ly sealed and isloated package. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-06204 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 A
47、PR 97 Case outline M Inches Millimeters Symbol Min Max Min Max A .240 .270 6.09 6.86 A1 .035 .045 0.89 1.14 A2 .140 BSC 3.55 BSC b .025 .035 0.64 0.89 D .815 .835 20.70 21.21 D1 .530 .550 13.46 13.97 D2 .092 2.37 e .100 BSC 2.54 BSC E .685 .695 17.40 17.65 L .105 2.67 L1 .697 .707 17.70 17.95 L2 .09
48、0 .110 2.29 2.79 p .155 .165 3.94 4.19 q .115 .125 2.92 3.18 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch- pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. The case outline M is a metal hermetically sealed and isloated package. FIGURE 1. Case outline - Continued. Pr
