1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02 tested at low dose rate. Make change to paragraphs 1.2.2, and 1.5. Make changes to footnotes 2/ and 3/ as specified under Table I. Make change to Table IIB and paragraph 4.4.4.1. - rrp 11-08-09 C. SAFFLE B Make correction to ca
2、se outline letter F descriptive designator as specified under paragraph 1.2.4. Add case outline X, descriptive designator CDFP4-F16. - ro 11-10-04 C. SAFFLE REV SHEET REV B B B B B B B B B B B B B B SHEET 15 16 17 18 19 20 21 22 23 24 25 26 27 28 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS
3、SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PI
4、THADIA APPROVED BY CHARLES F. SAFFLE MICROCIRCUIT, LINEAR, 0.8 GHz TO 2.5 GHz QUADRATURE MODULATOR, MONOLITHIC SILICON DRAWING APPROVAL DATE 10-04-27 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-09227 SHEET 1 OF 28 DSCC FORM 2233 APR 97 5962-E500-11 Provided by IHSNot for ResaleNo reproduct
5、ion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09227 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high rel
6、iability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The P
7、IN is as shown in the following example: 5962 R 09227 01 V F A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA ma
8、rked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Devi
9、ce type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 AD8346 Radiation hardened, 0.8 GHz to 2.5 GHz quadrature modulator 02 AD8346 Radiation hardened, 0.8 GHz to 2.5 GHz quadrature modulator 1.2.3 Device class designator. The device c
10、lass designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Cer
11、tification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style F GDFP2-F16 16 Flat pack X CDFP4-F16 16 Flat pack 1.2.5 Lead finish. The lead finish is as specifie
12、d in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09227 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LE
13、VEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VPS1, VPS2) . 5.5 V Input power LOIP, LOIN (relative to 50 ) . 10 dBm Input voltage IBBP, IBBN, QBBP, QBBN 0 V to 2.5 V Power dissipation (PD) 340 mW Maximum junction temperature (TJ) +150C Storage temperature range
14、 -65C to +150C Lead temperature (soldering 60 seconds) . +300C Thermal resistance, junction to case (JC) 38C/W Thermal resistance, junction to ambient (JA) . 64C/W 2/ 1.4 Recommended operating conditions. Supply voltage (VPS1, VPS2) . 2.7 to 5.25 V Ambient operating temperature range (TA) . -55C to
15、+125C 1.5 Radiation features: Device type 01: Maximum total dose available (dose rate = 50 300 rads(Si)/s) . 100 krads (Si) 3/ Device type 02: Maximum total dose available (dose rate 10 mrads(Si)/s) 50 krads (Si) 4/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The
16、following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufactur
17、ing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Micro
18、circuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolute maximum rating may cause permanent damage to t
19、he device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Measurement taken under absolute worst case conditions of still air. 3/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation e
20、nd point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, method 1019, condition A. 4/ For device type 02, radiation end point limits for the noted parameters are guaranteed for the conditions specified in MIL-STD-883, method 1019, condition D. Prov
21、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09227 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the
22、 text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for d
23、evice classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for devic
24、e class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V
25、 or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Block diagram. The timing waveforms shall be as specified on figur
26、e 2. 3.2.4 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request. 3.3 Electrical performance characteristics and postirradiation paramet
27、er limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the
28、 subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN is not feasible due to sp
29、ace limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with
30、 MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For
31、device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an appr
32、oved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-3
33、8535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of
34、microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verificatio
35、n and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of t
36、he reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 110 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MIC
37、ROCIRCUIT DRAWING SIZE A 5962-09227 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min M
38、ax RF OUTPUT section. VPS= 5 V; fLO= LO frequency = 800 MHz, LO input level = -6 dBm 4/ Output power POUT Single (lower) sideband, 4 01, 02 -11 -4 dBm fLO- fBB5 -11 -4 6 -11 -4 M,D,P,L,R 4 01 -11 4 M,D,P,L 4 02 -11 4 Carrier feedthrough PFDTH fLO4 01, 02 -35 dBm 5 -35 6 -35 M,D,P,L,R 4 01 -35 M,D,P,
39、L 4 02 -35 Sideband suppression PSUPP fLO+ fBB4 01, 02 -28 dBc 5 -28 6 -30 M,D,P,L,R 4 01 -28 M,D,P,L 4 02 -28 Second lower harmonic P2ndL fLO- 2fBB4 01, 02 -46 dBc 5 -49 6 -45 M,D,P,L,R 4 01 -46 M,D,P,L 4 02 -46 Second upper harmonic P2ndU fLO+ 2fBB4 01, 02 -49 dBc 5 -48 6 -48 M,D,P,L,R 4 01 -49 M,
40、D,P,L 4 02 -49 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09227 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Elec
41、trical performance characteristics continued. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max RF OUTPUT section continued. VPS= 5 V; fLO= LO frequency = 800 MHz, LO input level = -6 dBm 4/ Third upper harmonic P3rdU fLO+ 3fBB
42、4 01, 02 -45 dBc 5 -47 6 -42 M,D,P,L,R 4 01 -45 M,D,P,L 4 02 -45 RF OUTPUT section . VPS= 5 V; fLO= LO frequency = 1.9 GHz, LO input level = -6 dBm 4/ Output power POUT Single (lower) sideband, 4 01, 02 -13 -6 dBm fLO- fBB5 -18 -8 6 -13 -6 M,D,P,L,R 4 01 -13 -6 M,D,P,L 4 02 -13 -6 Carrier feedthroug
43、h PFDTH fLO4 01, 02 -35 dBm 5 -35 6 -35 M,D,P,L,R 4 01 -35 M,D,P,L 4 02 -35 Sideband suppression PSUPP fLO+ fBB4 01, 02 -25 dBc 5 -25 6 -26 M,D,P,L,R 4 01 -25 M,D,P,L 4 02 -25 Second lower harmonic P2ndL fLO- 2fBB4 01, 02 -45 dBc 5 -44 6 -45 M,D,P,L,R 4 01 -45 M,D,P,L 4 02 -45 See footnotes at end o
44、f table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09227 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics co
45、ntinued. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max RF OUTPUT section - continued. VPS= 5 V; fLO= LO frequency = 1.9 GHz, LO input level = -6 dBm 4/ Second upper harmonic P2ndU fLO+ 2fBB4 01, 02 -45 dBc 5 -46 6 -46 M,D,P
46、,L,R 4 01 -45 M,D,P,L 4 02 -45 Third upper harmonic P3rdU fLO+ 3fBB4 01, 02 -46 dBc 5 -50 6 -41 M,D,P,L,R 4 01 -46 M,D,P,L 4 02 -46 RF OUTPUT section. VPS= 5 V; fLO= LO frequency = 2.3 GHz, LO input level = -6 dBm 4/ Output power POUT Single (lower) sideband, 4 01, 02 -16 -7 dBm fLO- fBB5 -23 -10 6
47、-14 -7 M,D,P,L,R 4 01 -16 -7 M,D,P,L 4 02 -16 -7 Carrier feedthrough PFDTH fLO4 01, 02 -34 dBm 5 -35 6 -34 M,D,P,L,R 4 01 -34 M,D,P,L 4 02 -34 Sideband suppression PSUPP fLO+ fBB4 01, 02 -25 dBc 5 -25 6 -26 M,D,P,L,R 4 01 -25 M,D,P,L 4 02 -25 See footnotes at end of table. Provided by IHSNot for Res
48、aleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-09227 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics continued. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max RF OUTPUT section - continued. VPS= 5 V; fLO= LO frequency = 2.3 GHz, LO input level = -6 dBm 4/ Second lower harmon
