1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED F Convert to military drawing format. Delete vendor CAGE number 27014. Table I, change tPHL1(CL= 50 pF for subgroup 9) from 23 ns to 24 ns (subgroups 10 and 11) from 31 ns to 33 ns. Change tPLH2to tPLH1and tPHL3to tPHL2. Add LCC, outline letter 2 t
2、o case outlines (make editorial changes pertaining to this). Change CAGE code to 67268. 87-10-09 R. P. Evans G Update to reflect latest changes in format and requirements. Editorial changes throughout. -les 03-03-20 Raymond Monnin H Update to reflect latest changes in format and requirements. Correc
3、t paragraph in 3.5. Editorial changes throughout. les 05-08-02 Raymond Monnin THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. CURRENT CAGE CODE 67268 REV SHET REV SHET REV STATUS REV H H H H H H H H H OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 PMIC N/A PREPARED BY Monica L. Grosel DEFENSE SUPPLY C
4、ENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY D. A. DiCenzo COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Robert P. Evans MICROCIRCUIT, DIGITAL, BIPOLAR, LOW-POWER SCHOTTKY TTL, LATCH, AND AGENCIES OF THE DEPARTMENT OF DEF
5、ENSE DRAWING APPROVAL DATE 76-03-23 MONOLITHIC SILICON AMSC N/A REVISION LEVEL H SIZE A CAGE CODE 14933 76018 SHEET 1 OF 9 DSCC FORM 2233 APR 97 5962-E401-05 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76018 D
6、EFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying N
7、umber (PIN). The complete PIN is as shown in the following example: 76018 01 E X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 54LS279 Qu
8、adruple S-R latches 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 dual-in-line F GDFP2-F16 or CDFP3-F16 16 flat 2 CQCC1-N20 20 square chip carrier 1.2.3 Lead finish. T
9、he lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage . -0.5 V dc to +7.0 V dc Input voltage range . -1.5 V dc at -18 mA to +5.5 V dc Storage temperature range -65C to +150C Maximum power dissipation (PD) 1/ . 38 mW Lead temperature (soldering, 10
10、seconds) . +300C Thermal resistance, junction-to-case (JC): See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Supply voltage range (VCC) . 4.5 V dc to 5.5 V dc Minimum high level input voltage (VIH) . 2.0 V dc Maximum low level input voltage (VIL) 0.7 V dc Case o
11、perating temperature range (TC) -55C to +125C _ 1/ Maximum power dissipation is defined as VCCx ICC, and must withstand the added PDdue to short-circuit test; e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SI
12、ZE A 76018 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified
13、 herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Mi
14、crocircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicks
15、earch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes pre
16、cedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as
17、 specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers app
18、roved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shal
19、l not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF
20、-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth tables shall be as specified on figure 2. 3.2.4 Logic diagram. The logi
21、c diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. Provided by IHSNot for ResaleNo reproduct
22、ion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76018 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 4 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specif
23、ied in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. 3.5.1 Certification/complia
24、nce mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certi
25、ficate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the ma
26、nufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of c
27、hange. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall b
28、e made available onshore at the option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76018 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 5 DSCC FORM 2234 APR 97
29、 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroupsDevice type Limits Unit Min Max High level output voltage VOHVCC= 4.5 V, IOH= -0.4 mA, VIL= 0.7 V, VIH= 2.0 V 1, 2, 3 All 2.5 V Low level output voltage VOLVCC= 4.5 V, I
30、OL= 4.0 mA, VIN= 0.7 V, VIH= 2.0 V 1, 2, 3 All 0.4 V Input clamp voltage VICVCC= 4.5 V, IIN= -18 mA 1 All -1.5 V High level input current IIH1VCC= 5.5 V, VIH= 2.7 V 1, 2, 3 All 20 A IIH2VCC= 5.5 V, VIH= 5.5 V 1, 2, 3 All 100 A Low level input current IILVCC= 5.5 V, VIL= 0.4 V 1, 2, 3 All -400 A Shor
31、t circuit output current IOSVCC= 5.5 V, VOUT= 0.0 V 1/ 1, 2, 3 All -6 -130 mA Supply current ICCVCC= 5.5 V, VIN= 0.0 V 2/ 1, 2, 3 All 7 mA Functional tests See 4.3.1c 7 All tPHL19 All 21 ns VCC= 5.0 V, RL= 2 k 5% CL= 15 pF 10% 10, 11 All 29 ns 24 Propagation delay time, S to Q 3/ CL= 50 pF 10% 10, 1
32、1 All 33 ns tPLH19 22 CL= 15 pF 10% 10, 11 All 31 ns 27 CL= 50 pF 10% 10, 11 All 38 ns tPHL29 27 CL= 15 pF 10% 10, 11 All 38 ns 32 Propagation delay time, R to Q CL= 50 pF 10% 10, 11 All 45 ns 1/ Not more than one output will be tested at a time, and the duration of the test condition shall not exce
33、ed one second. 2/ ICCshall be measured with all R inputs grounded, all S inputs at 4.5 Vm, and all outputs open. 3/ Propagation delay time testing may be performed using either CL= 15 pF or CL= 50 pF. However, the manufacturer must certify and guarantee that the microcircuits meet the switching test
34、 limits specified for a 50 pF load. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76018 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 6 DSCC FORM 2234 APR 97 Case outlines E and
35、 F 2 Terminal number Terminal symbol 1 1R NC 2 1 S1 1R 3 1 S2 1S1 4 1Q 1 S2 5 2R 1Q 6 2 S NC 7 2Q 2R 8 GND 2 S 9 3Q 2Q 10 3R GND 11 3 S1 NC 12 3 S2 3Q 13 4Q 3R 14 4R 3S1 15 4 S 3S2 16 VCCNC 17 - - - 4Q 18 - - - 4R 19 - - - 4 S 20 - - - VCCFIGURE 1. Terminal connections. INPUTS OUTPUTs S + R Q H H Q0
36、L H H H L L L L H* H = high level. L = low level. Q0= The level of Q before the indicated input conditions were established. * = This output level is pseudo stable; that is, it may not persist when the S and R inputs return to their inactive (high) level. + = For latches with double S inputs: H = bo
37、th S inputs high. L = one or both S inputs low. FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76018 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 7 DSCC F
38、ORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76018 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 8 DSCC FORM 2234 APR 97 4. VERIFICATIO
39、N 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following addit
40、ional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit
41、shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical paramete
42、r tests prior to burn-in are optional at the discretion of the manufacturer. TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters (method 5004) - - - Final electrical test parameters (meth
43、od 5004) 1*, 2, 3, 9 Group A test requirements (method 5005) 1, 2, 3, 7, 9, 10*, 11* Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. * Subgroups 10 and 11, if not tested, shall be guaranteed to the specified limits in table I. 4.3 Quality conformance
44、 inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, 6, and 8 in t
45、able I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroup 7 shall include verification of the truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 76018 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO
46、 43218-3990 REVISION LEVEL H SHEET 9 DSCC FORM 2234 APR 97 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be main
47、tained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 o
48、f MIL-STD-883. (2) TA= +125C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-prepared
