1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change drawing to military drawing format. Correct recommended operating conditions (VIL). Correct prop delays (max limits). Editorial changes throughout. 88-02-09 M. A. Frye B Changes in accordance with NOR 5962-R336-923. tvn 92-10-05 Monica L.
2、Poelking C Redraw with changes. Update to current requirements. Editorial changes throughout. -gap 05-12-08 Raymond Monnin CURRENT CAGE CODE 67268 THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11
3、 PMIC N/A PREPARED BY Christopher A. Rauch DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Raymond Monnin COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, ADVANCED LOW-POWE
4、R SCHOTTKY TTL, MULTIPLEXER, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 85-05-6 MONOLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 14933 84134 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E509-05 Provided by IHSNot for ResaleNo reproduction or networking permitted without
5、 license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84134 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in ac
6、cordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 84134 01 E X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type. The device type identify the circuit function as
7、follows: Device type Generic number Circuit function 01 54ALS153 Dual 1 of 4 multiplexer 1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 dual-in-line F GDFP2-F16 or CDFP
8、3-F16 16 flat 2 CQCC1-N20 20 square chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range . -0.5 V dc minimum to +7.0 V dc maximum Input voltage range -1.5 V dc at -18 mA to +7.0 V dc Storage temperature -65C
9、to +150C Maximum power dissipation (PD) per device 1/ 77 mW Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Supply voltage (VCC) 4.5 V dc minimum to 5.5 V dc maximum Mini
10、mum high level input voltage (VIH) . 2.0 V dc Maximum low level input voltage (VIL): VIL= +125C . 0.7 V dc VIL= +25C 0.8 V dc VIL= -55C . 0.8 V dc Case operating temperature range (TC) -55C to +125C _ 1/ Maximum power dissipation is defined as VCCx ICC, and must withstand the added PDdue to short-ci
11、rcuit test; e.g., IO. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84134 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Gover
12、nment specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICAT
13、ION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard M
14、icrocircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
15、2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENT
16、S 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or
17、a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) pla
18、n may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML fl
19、ow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The term
20、inal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specifi
21、ed on figure 4 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted wi
22、thout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84134 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrica
23、l tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. 3.5.1 Certification/compliance mark. A compliance indicat
24、or “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certif
25、icate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the
26、requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change
27、to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at th
28、e option of the reviewer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84134 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performan
29、ce characteristics. 1/ Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Limits Unit Min MaxHigh level output voltage VOHVCC= 4.5 V, 2/ VIH= 2.0 V, VIL = 0.8 V 1, 3 2.4 V IOH= -1.0 mA VIL= 0.7 V 2 2.4 Low level output voltage VOLVIL= 0.8 V 1, 3 0.4 V VCC= 4.5 V, 2/ IO
30、L= 12 mA, VIH= 2.0 V VIL= 0.7 V 2 0.4 Input clamp voltage VICVCC= 4.5 V, IIN= -18 mA, TC= +25C 1 -1.5 V High level input current IIH1VCC= 5.5 V, VIN= 2.7 V, All other inputs = 0.0 V 1, 2, 3 20 A IIH2VCC= 5.5 V, VIN= 7.0 V, All other inputs = 0.0 V 100 Low level input current IILVCC= 5.5 V, VIN= 0.4
31、V, All other inputs = 4.5 V 1, 2, 3 -100 A Output current IOVCC= 5.5 V, 3/ VOUT= 2.25 V 1, 2, 3 -20 -112 mA Supply current, ICCVCC= 5.5 V, All inputs = 4.5 V 1, 2, 3 14 mA Propagation delay time, A, B to Y tPLH1 VCC= 5.0 V, CL= 50 pF 10%, 9, 10, 11 5 21 ns tPHL1 RL= 500 5% 4/ (See figure 4) 9, 10, 1
32、1 5 32 ns Propagation delay time, C0, C1, C2, C3 to Y tPLH2 9, 10, 11 3 12 ns tPHL2 9, 10, 11 2 21 ns Propagation delay time, G to Y tPLH3 9, 10, 11 5 18 ns tPHL3 9, 10, 11 3 22.5 ns 1/ Unused inputs that do not directly control the pin under test must be put at 2.5 V or 0.4 V and shall not exceed 5
33、.5 V or go less than 0.0 V. No inputs shall be floated. 2/ All outputs must be tested. In the case where only one input at VILmaximum or VIHminimum produces the proper output state, the test must be performed with each input being selected as the VILmaximum or VIHminimum input. 3/ The output conditi
34、ons have been chosen to produce a current that closely approximated one half of the true short circuit output current, IOS. Not more than on output shall be tested at one time and the duration of the test shall not exceed one second. 4/ Propagation delay limits are based on single output switching.
35、Unused outputs = 3.5 V or 0.3 V Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84134 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 Case outlines E, F 2 Te
36、rminal number Terminal symbol 1 G1 NC 2 B G1 3 1C3 B 4 1C2 1C3 5 1C1 1C2 6 1C0 NC 7 1Y 1C1 8 GND 1C0 9 2Y 1Y 10 2C0 GND 11 2C1 NC 12 2C2 2Y 13 2C3 2C0 14 A 2C1 15 G2 2C2 16 VCCNC 17 - - - 2C3 18 - - - A 19 - - - G2 20 - - - VCCFIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduct
37、ion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84134 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Select inputs A and B are common to both sections. H = High voltage level L = Low voltage level
38、X = Irrelevant FIGURE 2. Truth table. SELECT DATA INPUTS STROBE OUTPUT INPUTS B A C0 C1 C2 C3 G Y X X X X X X H L L L L X X X L L L L H X X X L H L H X L X X L L L H X H X X L H H L X X L X L L H L X X H X L H H H X X X L L L H H X X X H L H Provided by IHSNot for ResaleNo reproduction or networking
39、 permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84134 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro
40、m IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84134 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 NOTES: 1. CLincludes probe and jig capacitance. 2. All input pulses have the following characteristics: PRR 10 MHz, duty cycle = 50 percent, tr
41、= tf= 3 ns 1 ns. 3. The outputs are measured one at a time with one input transition per measurement. FIGURE 4. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84134 DEFENSE S
42、UPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of M
43、IL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision le
44、vel control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and
45、 final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883,
46、method 5005, table I) Interim electrical parameters (method 5004) - - - Final electrical test parameters (method 5004) 1*, 2, 3, 9 Group A test requirements (method 5005) 1, 2, 3, 7, 8, 9, 10, 11 Group C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. 4.3 Qua
47、lity conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4,
48、5, and 6 in table I, method 5005 of MIL-STD-883 shall be omitted. c. Subgroups 7 and 8 shall include verification of the truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 84134 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 11 DSCC FORM 2234 APR 97 4.3.2 Groups C and D inspections. a. End-point electrical parameters s
