1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change tPLH, tPHL, and footnotes in table I. Add figure 3. Editorial changes throughout. Change footnote 1/ in 1.3. 88-04-04 M. A. Frye B Changes IAW NOR 5962-R339-92. -tvn 92-10-05 Monica L. Poelking C Update to reflect latest changes in format
2、and requirements. Editorial changes throughout. - les 01-10-31 Raymond Monnin D Update drawing to current requirements. Editorial changes throughout. - gap 09-01-09 Robert M. Heber The original first sheet of this drawing has been replaced. REV SHET REV SHET REV STATUS REV D D D D D D D D D D OF SHE
3、ETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Monica L. Poelking DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Ray Monnin COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DI
4、GITAL, BIPOLAR, ADVANCED LOW POWER SCHOTTKY TTL, NOR GATES, AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 87-08-17 MONOLITHIC SILICON AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-86838 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E361-08 Provided by IHSNot for ResaleNo reprodu
5、ction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant,
6、 non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-86838 01 D X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s).
7、 The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ALS27 Triple, three-input, positive NOR gates 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Pa
8、ckage style D GDFP1-F14 or GDFP2-F14 14 Flat pack 2 CQCC1-N20 20 Square chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage . -0.5 V dc minimum to +7.0 V dc maximum Input voltage range . -1.5 V dc at -18 mA to +7.
9、0 V dc Storage temperature range . -65C to +150C Maximum power dissipation (PD) per device 1/ 22.0 mW Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Supply voltage range (
10、VCC) . +4.5 V dc minimum to 5.5 V dc maximum Minimum high level input voltage (VIH) 2.0 V dc Maximum low level input voltage (VIL): TC= +125C . 0.7 V dc TC= -55C 0.8 V dc TC= +25C . 0.8 V dc Case operating temperature range (TC) -55C to +125C _ 1/ Maximum power dissipation is defined as VCCx ICC, an
11、d must withstand the added PDdue to short circuit test (e.g. IOS). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC
12、FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicita
13、tion or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF D
14、EFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelp
15、hia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obt
16、ained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and quali
17、fied manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Qualit
18、y Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to ide
19、ntify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal
20、connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Test circuit and switching waveforms. The test circuit and switching waveform
21、s shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical
22、test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86838 DEFENSE SUPPLY CENTER COL
23、UMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of
24、the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The c
25、ompliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source
26、 of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance
27、. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. D
28、SCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection proced
29、ures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of M
30、IL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipat
31、ion, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of th
32、e manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance ch
33、aracteristics. Test Symbol Conditions -55C TC+125C unless otherwise specified Group A subgroups Limits Unit Min Max High level output voltage VOHVIL= 0.8 V 1, 3 2.5 V VIH= 2.0 V, VCC= 4.5 V, IOH= -0.4 mA 3/ 4/ VIL= 0.7 V 2 Low level output voltage VOLVIL= 0.8 V 1, 3 0.4 V VIH= 2.0 V, VCC= 4.5 V, IOL
34、= 4.0 mA 5/ 4/ VIL= 0.7 V 2 Input clamp voltage VI CVCC= 4.5 V, IIH= -18 mA 1, 2, 3 -1.5 V High level input current II H1 VCC= 5.5 V, VIN= 2.7 V, All other inputs = 0.0 V 1, 2, 3 20 A II H2 VCC= 5.5 V, VIN= 7.0 V, All other inputs = 0.0 V 1, 2, 3 100 A Low level input current IILVCC= 5.5 V, VIN= 0.4
35、 V, All other inputs = 4.5 V 1, 2, 3 -0.1 mA Output current IOVCC= 5.5 V, VOUT= 2.25 V 6/ 1, 2, 3 -20 -112 mA High level supply current ICCHVCC= 5.5 V, VIN 0.4 V (All inputs) 1, 2, 3 1.8 mA Low level supply current ICCL VCC = 5.5 V, VIN 4.5 V (All inputs) 1, 2, 3 4.0 mA Functional tests See 4.3.1c 7
36、/ 7, 8 tPHL 9, 10, 11 1 8 ns Propagation delay time, any input to Y tPLH VCC= 4.5 V to 5.5 V, CL= 50 pF, RL= 500 8/See figure 3 9, 10, 11 2 16 ns 1/ Unused inputs that do not directly control the pin under test must be 2.5 V or 0.4 V. 2/ Unused inputs shall not exceed 5.5 V or go less than 0.0 V. No
37、 inputs shall be floated. 3/ One input to gate under test must be = VIL, the other inputs shall be 0.7 V. 4/ All outputs must be tested. In the case where only one input at VILmaximum or VIHminimum produces the proper output state, the test must be performed with each input being selected as the VIL
38、maximum or VIHminimum input. 5/ One input to gate under test must be = VIH, the other inputs shall be 0.7 V. 6/ The output conditions have been chosen to produce a current that closely approximates one-half of the true short circuit output current, IOS. Not more than one output will be tested at a t
39、ime and the duration of the test condition shall not exceed one second. 7/ Functional tests shall be conducted at input test conditions of 0.0 V VIL VOLand VOH VIH VCC. 8/ The propagation delay limits are based on single output switching. Unused inputs = 3.5 V or 0.3 V. Provided by IHSNot for Resale
40、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 Case outlines D 2 Terminal number Terminal symbols 1 1A NC 2 1B 1A 3 2A 1B 4 2B
41、 2A 5 2C NC 6 2Y 2B 7 GND NC 8 3Y 2C 9 3A 2Y10 3B GND 11 3C NC12 1Y 3Y 13 1C 3A 14 VCC 3B15 NC16 3C 17 NC18 1Y 19 1C20 VCC FIGURE 1. Terminal connections. Inputs Output A B C Y H X X L X H X L X X H L L L L H H = High voltage level L = Low voltage level X = Irelevant FIGURE 2. Truth table. Provided
42、by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo re
43、production or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-86838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 NOTES: 1. CLincludes probe and jig capacitance. 2. All input pulses have the followi
44、ng characteristics: PRR 10 MHz, duty cycle 50%, tr= tf= 3 ns 1 ns. 3. The outputs are measured one at a time with one input transition per measurement. FIGURE 4. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ST
45、ANDARD MICROCIRCUIT DRAWING SIZE A 5962-86838 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electri
46、cal parameters (method 5004) - - - Final electrical test parameters (method 5004) 1*, 2, 3, 7, 8, 9, 10, 11 Group A test requirements (method 5005) 1, 2, 3, 7, 8, 9, 10, 11 Groups C and D end-point electrical parameters (method 5005) 1, 2, 3 * PDA applies to subgroup 1. 4.3 Quality conformance inspe
47、ction. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-883 including groups A, B, C, and D inspections. The following additional criteria shall apply. 4.3.1 Group A inspection. a. Tests shall be as specified in table II herein. b. Subgroups 4, 5, and 6 in table I, m
48、ethod 5005 of MIL-STD-883 shall be omitted. c. Subgroups 7 and 8 shall include verification of the truth table. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request.
