1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R025-93. 93-03-11 M. A. FRYE B Add case outline N. Techical and editorial changes throughout. Redrawn. 95-03-27 M. A. FRYE C Changes in accordance with NOR 5962-R132-96. 96-05-24 M. A. FRYE D Make changes to ca
2、se outline N dimensions A, E, S, and S1. Redrawn. - ro 98-04-13 R. MONNIN E Add radiation hardness requirements. Add CAGEs 27851, 21845 and case outline M. Make changes to 1.2, 1.2.2, PD, theta JC, and theta JA as specified under paragraph 1.3, table I, figure 1 and figure 2. - ro 00-01-28 R. MONNIN
3、 F Add case outlines 4 and 5. Make correction to case outline N pin descriptions. - ro 02-02-11 R. MONNIN G Add footnote to case outline U, TO-257 package as specified under 1.2.3 and figure 1. -rrp 05-02-04 R. MONNIN H For case outline T only, add footnote 1/ under 1.2.3 and make change to note 2 u
4、nder figure 1. -rrp 06-01-23 R. MONNIN THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV H H H SHEET 15 16 17 REV STATUS REV H H H H H H H H H H H H H H OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY JOSEPH A. KERBY DEFENSE SUPPLY CENTER COLUMBUS STANDAR
5、D MICROCIRCUIT DRAWING CHECKED BY CHARLES E. BESORE COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, 5 VOLT NEGATIVE REGULATOR FIXED, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DR
6、AWING APPROVAL DATE 89-08-28 AMSC N/A REVISION LEVEL H SIZE A CAGE CODE 67268 5962-88746 SHEET 1 OF 17 DSCC FORM 2233 APR 97 5962-E156-06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88746 DEFENSE SUPPLY C
7、ENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). Th
8、e complete PIN is as shown in the following example: 5962 F 88746 01 X X Federal RHA Device Case Lead stock class designator type outline finish designator (see 1.2.1) (see 1.2.2) (see 1.2.3) (see 1.2.4) / / Drawing number 1.2.1 RHA designator. RHA marked devices shall meet the MIL-PRF-38535 or MIL-
9、PRF-38535, Appendix A specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 7905A 1.0 A negative regulator, fix
10、ed 5 volt 1.2.3 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style M See figure 1 3 Surface mount N CBCC2-N3 3 Bottom terminal chip carrier T 1/ See figure 1 3 TO-257 Single row flange mount, glass seal
11、ed U 1/ See figure 1 3 TO-257 Single row flange mount with isolated tab, glass sealed X See figure 1 3 TO-39 Can Y See figure 1 2 TO-3 Flange mount Z MBFM4-P2 2 TO-66 Flange mount 2 CQCC1-N20 20 Square leadless chip carrier 4 See figure 1 3 Flange mount, glass sealed with gull wing leads 5 CBCC1-N3
12、3 Bottom terminal chip carrier 1.2.4 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1/ For outline letters T and U, CAGE 34333 manufacturers the TO-257 package with ceramic seal.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
13、,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88746 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. Input voltage: Operating or input shorted to ground . -35 V dc Transient -43 V dc 2/ Storage temperature range -65
14、C to +150C Lead temperature (soldering, 10 seconds) +300C Power dissipation (PD): TC= +25C: Cases M, N, T, U, Z, 4, and 5 15 W Cases X and 2 2 W Case Y 20 W TA= +25C: Cases M, T, U, and Z . 3.0 W Case N . 15.0 W Case X 1.0 W Case Y 3.6 W Case 2 1040 mW Case 4 . 1.7 W Case 5 . 1.3 W Junction temperat
15、ure (TJ) +150C 3/ Thermal resistance, junction-to-case (JC): Case M 5.5C/W Cases N and T . 3.5C/W Case U . 4.2C/W Case X . 15C/W Case Y . 3C/W Case Z . 6C/W Case 2 25C/W Case 4 . 5.1C/W Case 5 . 3.6C/W Thermal resistance, junction-to-ambient (JA): Cases M, T, U, and Z (device type 01). 42C/W Cases N
16、, X, and 2 120C/W Case Y . 35C/W Case 4 . 60C/W Case 5 . 80C/W 1.4 Recommended operating conditions. Input voltage range (VIN) . -7.5 V dc to -20 V dc Ambient operating temperature range (TA) -55C to +125C 1.5 Radiation features: 4/ Maximum total dose available (dose rate = 50 300 rads(Si)/s) . 300
17、Krads (Si) _ 2/ The 43-volt input rating refers to the ability of the regulator to withstand high line or transient conditions without damage. Since the regulators maximum current capability is reduced, the output may fall out of regulation at high input voltages under nominal loading. 3/ The device
18、 is protected by a thermal shutdown circuit which is designed to turn off the output transistor whenever the device junction temperature is in excess of +150C. 4/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end point lim
19、its for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883, method 1019, condition A.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88746 DEFENSE SUPPLY CENTER COLUMBUS COLU
20、MBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issue
21、s of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard
22、 Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from th
23、e Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, su
24、persedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawi
25、ng that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity app
26、roval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q
27、” or “QML” certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outl
28、ines. The case outlines shall be in accordance with 1.2.3 herein and on figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be as specified on figure 3. 3.3 Electrical performance cha
29、racteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC
30、IRCUIT DRAWING SIZE A 5962-88746 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit
31、 Min Max Output voltage VOUTTA= +25C 1 01 -4.95 -5.05 V VIN= -7.5 V to -20 V 4/ 1,2,3 -4.85 -5.15 M,D,P,L,R,F 1 -4.95 -5.05 Line regulation 5/ 6/ VRLINEVIN= -7.5 V to -20 V 1 01 12 mV -55C TJ +125C 2,3 25 M,D,P,L,R,F 1 12 VIN= -8.0 V to -12 V 1 5 -55C TJ +125C 2,3 12 M,D,P,L,R,F 1 5 Load regulation
32、5/ VRLOADIO= 5.0 mA to 1.5 A 7/ 1 01 20 mV -55C TJ +125C 2,3 25 M,D,P,L,R,F 1 20 IO= 250 mA to 750 mA 7/ 1 15 -55C TJ +125C 2,3 30 M,D,P,L,R,F 1 15 IO= 5.0 mA to 500 mA 8/ 1 25 -55C TJ +125C 2,3 50 Standby current drain ISCD1 01 2.5 mA 2,3 3.0 M,D,P,L,R,F 1 2.5 Standby current drain change with line
33、 ISCD (line) VIN= -7.0 V to -20 V 1,2,3 01 0.4 mA M,D,P,L,R,F 1 0.4 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88746 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-399
34、0 REVISION LEVEL H SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Standby current drain change with load ISCD (load) IO= 5.0 mA to 10
35、00 mA 1,2,3 01 0.4 mA M,D,P,L,R,F 1 0.4 Dropout voltage VDOVOUT= 100 mV 7/ IO= 1.0 A 1,2,3 01 2.5 V M,D,P,L,R,F 1 2.5 VOUT= 100 mV 8/ IO= 500 mA 1,2,3 2.5 Peak output current IO(PK)TA= +25C 7/ 1 01 1.5 3.3 A M,D,P,L,R,F 1 1.5 3.3 TA= +25C 8/ 1 0.5 1.7 Output noise voltage 9/ NOf = 10 Hz to 100 kHz,
36、TA= +25C 7 01 40 V/V rms Long term stability 9/ VOUT/ t t = 1000 hours, TA= +25C 7 01 75 mV Short circuit current 10/ IOSVIN= -35 V 7/ 1 01 1.2 A 2,3 2.8 M,D,P,L,R,F 1 1.2 VIN= -35 V 8/ 1 0.7 2,3 2.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted
37、without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88746 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ 3/ -55C TA +125C unless other
38、wise specified Group A subgroups Device type Limits Unit Min MaxRipple rejection VIN/ VOUTf = 120 Hz, VIN= 10 V, VIN= -8 V to -18 V 4 01 63 dB 5,6 9/ 60 M,D,P,L,R,F 4 63 1/ Devices supplied to this drawing have been characterized through all levels M, D, P, L, R, F of irradiation. However, this devi
39、ce is only tested at the “F” level. Pre and Post irradiation values are identical unless otherwise specified in table I. When performing post irradiation electrical measurements for any RHA level, TA= +25C. 2/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced
40、 low dose rate effects. Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883, method 1019, condition A. 3/ Unless otherwise specified, VIN= -10 V and IO= 500 mA for cases M, N, T, U, Y, Z, 4, and 5. VIN= -10 V and IO= 100 mA for cases X
41、and 2. Maximum test current for cases X and 2 is 500 mA. 4/ For cases X and 2: IO= 5 mA to 500 mA, P 2 W. For case Y: IO= 5 mA to 1.0 A, P 20 W. For cases M, N, T, U, Z, 4, and 5: IO= 5 mA to 1.0 A, P 15 W. 5/ All measurements except output noise voltage and ripple rejection are made at constant jun
42、ction temperature and with low duty cycle. 6/ Minimum load current for full line regulation is 5.0 mA. 7/ For cases M, N, T, U, Y, Z, 4, and 5 only. 8/ For cases X and 2 only. 9/ Guaranteed, if not tested, to the limits specified. 10/ Short circuit protection is only assured up to VIN= -35 V. 3.4 El
43、ectrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2
44、herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” s
45、hall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of
46、 compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirem
47、ents of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking
48、permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-88746 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL H SHEET 8 DSCC FORM 2234 APR 97 Case outline M Symbol Inches Millimeters Min Max Min Max A .160 - 4.06 - A2.080 - 2.03 - b - .035 - 0.89 C .020 - 0.51 - D - .425 -
