1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R148-92. 92-02-20 Alan BaroneB Table I; changed the max limit for the overload power dissipation test from 6 watts to 7 watts. Redrew entire document. -sld 01-03-26 Raymond Monnin C Update drawing. -gz 08-01-29
2、 Robert M. Heber D Table II, add note to Group C end-point test parameters. Update boilerplate paragraphs. -gz 10-02-02 Charles F. Saffle THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12
3、PMIC N/A PREPARED BY Steve Duncan DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Robert M. Heber COLUMBUS, OHIO 43216-3990 http:/www.dscc.dla.mil/ THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, HYBRID, LINEAR, 5-VOLT, AND AG
4、ENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-03-15 SINGLE CHANNEL, DC/DC CONVERTER AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-89683 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E178-10Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS
5、-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89683 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case out
6、lines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 89683 01 H X X Federal RHA Device Devic
7、e Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be mar
8、ked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 AHE2805S DC/DC converter, 15 W, 5 V output 02 AHE2805S/CH-SLV DC/DC converter, 15 W, 5 V o
9、utput 03 AHE2805S/CH-MSTR DC/DC converter, 15 W, 5 V output 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification
10、 (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended
11、 for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the
12、manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquis
13、ition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limite
14、d temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89683 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outlines. The case
15、 outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 10 Dual-in-line Z See figure 1 10 Flange package 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input
16、voltage . -0.5 V dc to +50 V dc Power dissipation (PD) . 7 W Lead temperature (soldering, 10 seconds) +300C Storage temperature -65C to +135C 1.4 Recommended operating conditions. Input voltage range . +17V dc to +40 V dc Case operating temperature range (TC). -55C to +125C Output power 2/ 15 W 2. A
17、PPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEP
18、ARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 -
19、 List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order
20、 of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the a
21、bsolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Derate output power linearly above case temperature +125C to 0 at +135C.Provided by IHSNot for ResaleNo reproduction or networking permitted w
22、ithout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89683 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K
23、 shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize t
24、he tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construc
25、tion, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified
26、 on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements
27、shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor simil
28、ar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device ty
29、pe listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.
30、7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and he
31、rein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
32、modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5
33、962-89683 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A subgroups Device types Limits Unit Min Max
34、Output voltage VOUTIOUT= 0 1 All 4.95 5.05 V 2,3 4.90 5.10 Output adjust 1/ VOAPin 3 shorted to pin 4 1,2,3 All 4 6 %VOUTOutput current 2/ IOUTVIN= 17, 28, and 40 V dc 1,2,3 All 3000 mA Output ripple voltage 3/ VRIPVIN= 17, 28, and 40 V dc, B.W. = dc to 2 MHz 1,2,3 All 60 mV p-p Output power 2/ 4/ P
35、OUTVIN= 17, 28, and 40 V dc 1,2,3 All 15 W Line regulation VRLINEVIN= 17, 28, and 40 V dc, IOUT= 0, 1.5, and 3.0 A 1 All 5 mV 2,3 25 Load regulation VRLOADVIN= 17, 28, and 40 V dc, IOUT= 0, 1.5, and 3.0 A 1,2,3 All 50 mV Input current IINIOUT= 0, inhibit (pin 2) tied to input return (pin 10) 1,2,3 A
36、ll 18 mA IOUT= 0, inhibit (pin 2) = open 35 Input ripple current 3/ IRIPIOUT= 3.0 A, B.W. = dc to 2 MHz 1,2,3 All 50 mA p-p Efficiency EFF IOUT= 3.0 A, TC= +25C 1 All 80 % Isolation ISO Input to output or any pin to case (except pin 8) at 500 V dc, TC= +25C 1 All 100 M Capacitive load 5/ 6/ CLNo eff
37、ect on dc performance, TC= +25C 4 All 500 F Power dissipation, load fault PDOverload, TC= +25C 7/ 1 All 7 W Short circuit, TC= +25C 6 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A
38、5962-89683 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A subgroups Device types Limits
39、Unit Min Max Switching frequency FSIOUT= 3.0 A 4,5,6 01 225 275 kHz 02 225 245 03 250 275 Output response to step transient load changes 8/ VOTLOAD50% load to/from 100% load 4 All -300 +300 mV pk 5,6 -450 +450 No load to/from 50% 4 All -500 +500 5,6 -750 +750 Recovery time step transient load change
40、s 8/ 9/ TTLOAD50% load to/from 100% load 4,5,6 All 70 s No load to/from 50% load 200 50% load to no load 5 ms Output response to transient step line changes 6/ 10/ VOTLINE Input step 17 to 40 V dc 4 All 300 mV pk 5,6 450 Input step 40 to 17 V dc 4,5,6 All -1000 Recovery time transient step line chan
41、ges 6/ 9/ 10/ TTLINEInput step 17 to 40 V dc 4,5,6 All 800 s Input step 40 to 17 V dc 800 Turn on overshoot VtonOSIOUT= 0 A 4 All 500 mV pk 5,6 550 IOUT= 3.0 A 4,5,6 550 Turn-on delay TonDIOUT= 0 A and 3.0 A 11/ 4,5,6 All 10 ms Load fault recovery 6/ trLF4,5,6 All 10 ms See footnotes at top of next
42、page. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89683 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characterist
43、ics - Continued. 1/ The output voltage of this device can be adjusted upward by connecting pin 3 and pin 4 as follows: Output adjustment resistor values Resistance pin 3 to pin 4 Output voltage increase, % 0 390 k +1% 145 k +2% 63 k +3% 22 k +4% 0 +5% 2/ Parameter guaranteed by line and load regulat
44、ion tests. 3/ Bandwidth guaranteed by design. Tested for 20 kHz to 2 MHz. 4/ For operation at 16 V dc input, derate output by 33 percent. 5/ Capacitive load may be any value from 0 to the maximum limit without affecting dc performance. A capacitive load in excess of the maximum limit will not distur
45、b loop stability but may interfere with the operation of the load fault detection circuitry, appearing as a short circuit during turn on. 6/ Parameter shall be tested as part of design characterization and after design and or process changes. Therefore the parameter shall be guaranteed to the limits
46、 specified in table I. 7/ An overload is that condition with a load in excess of the rated load but less than that necessary to trigger the short circuit protection and is the condition of maximum power dissipation. 8/ Load step transition time between 2 and 10 microseconds. 9/ Recovery time is meas
47、ured from the initiation of the transient to where VOUThas returned to within 1 percent of VOUTat 50 percent load. 10/ Input step transition time between 2 and 10 microseconds. 11/ Turn on delay time measurement is for either a step application of power at input or the removal of a ground signal fro
48、m the inhibit pin (pin 2) while power is applied to the input. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89683 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Min Max Min Max A 12.57 .495 b 0.89 1.14 .035 .045 D 53.85 2.120 e 10.03 10.28 .395 .405
