1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update to reflect latest changes in format and requirements. Editorial changes throughout. Les 05-07-15 Raymond Monnin B Update drawing as part of 5 year review. - jt 12-04-17 C. SAFFLE THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. R
2、EV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Larry T. Gauder DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AN
3、D AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Tim H. Noh APPROVED BY D. R. Cool MICROCIRCUIT, DIGITAL, BIPOLAR, OCTAL BUS TRANSCEIVER WITH THREE-STATE NONINVERTING OUTPUTS, MONOLITHIC SILICON DRAWING APPROVAL DATE 91-05-08 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-90506 SHEET 1 OF 1
4、1 DSCC FORM 2233 APR 97 5962-E310-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90506 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. Th
5、is drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-90506 01 R X Drawing number Device type (see 1.2.1)
6、Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 54F623 Octal bus transceiver with three-state noninverting outputs 02 54F621 Octal bus transceiver with open-collector noninver
7、ting outputs 1.2.2 Case outline. The case outline are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 dual-in-line S GDFP2-F20 or CDFP3-F20 20 flat 2 CQCC1-N20 20 square chip carrier 1.2.3 Lead finish. The lead f
8、inish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage range -0.5 V dc to +7.0 V dc dc Input voltage . -1.2 V dc at -18 mA to +7.0 V dc Voltage applied to a disabled three-state output . -0.5 V dc to +5.5 V dc Voltage applied to any output in the high state
9、. -0.5 V dc to VCCInput current range -30 mA to +5.0 mA Current into any output in the low state: (Any A) . 40 mA (Any B) . 96 mA Storage temperature range . -65C to +150C Maximum power dissipation (PD) 2/ 770 mW Lead temperature (soldering, 10 seconds) . +300C Thermal resistance, junction-to-case (
10、JC) . See MIL-STD-1835 Junction temperature (TJ) +175C _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operatiion at the maximum levels may degrade performance and affect reliability. 2/ Maximum power dissipation is defined as VCCx ICC, and must wit
11、hstand the added PDdue to short circuit test; for device 01; e.g., IOS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90506 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM
12、2234 APR 97 1.4 Recommended operating conditions. Supply voltage range (VCC) . +4.5 V dc to +5.5 V dc Minimum high level input voltage (VIH) . 2.0 V dc Maximum low level input voltage (VIL) 0.8 V dc Maximum input clamp current (II C) . -18mA Maximum high level output current (IOH) (Device 01): (Any
13、A) . -3 mA (Any B) . -12 mA Maximum high level output voltage (VOH) (Device 02) . 5.5 V Maximum low level output current (IOL): (Any A) . 20 mA (Any B) . 48 mA Case temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following spec
14、ification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General S
15、pecification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawin
16、gs. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the
17、references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF
18、-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535 may be proces
19、sed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect for
20、m, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. Provided by IHSNot for ResaleNo reproduction or networking permitted witho
21、ut license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 12-04-17 Approved sources of supply for SMD 5962-90565 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revise
22、d to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DLA Land and Maritime -VA. This information bulletin is superseded by the next dated revision of MIL-HDBK-103 and QML-38535. DL
23、A Land and Maritime maintains an online database of all current sources of supply at http:/www.landandmaritime.dla.mil/Programs/Smcr/. Standard microcircuit drawing PIN 1/ Vendor CAGE number Vendor similar PIN 2/ 5962-9050601RA 3/ 3/ SNJ54F623J 54F623/BLA 5962-9050601SA 01295 3/ SNJ54F623W 54F623/BK
24、A 5962-90506012A 3/ 3/ SNJ54F623FK 54F623/B2A 5962-9050602RA 3/ SNJ54F621J 5962-9050602SA 3/ SNJ54F621W 5962-90506022A 3/ SNJ54F621FK 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead fi
25、nish is not listed contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. 3/ Not available from an approved source. Vendor CAGE Vendor name number and addre
26、ss 01295 Texas Instruments, Inc. Semiconductor Group 8505 Forest Ln. PO Box 660199 Dallas, TX 75243 POC U.S. Highway 75 South P.O. Box 84, M/S 853 Sherman, TX 75090-9493 The information contained herein is disseminated for convenience only and the Government assumes no liability whatsoever for any inaccuracies in the information bulletin. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
