1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Made technical changes to table I. Editorial changes throughout. 91-11-15 G. A. Lude B Changes in accordance with NOR 5962-R056-94. 93-12-15 K. A. Cottongim C Update drawing requirements to MIL-PRF-38534. 01-03-13 Raymond Monnin D Correct paragra
2、phs 4.2.a.2 and 4.3.3.b.2. 05-12-01 Raymond Monnin E Added footnote 1 to table II, under group C end-point electricals. Updated drawing paragraphs. -sld 11-12-06 Charles F. Saffle THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E OF SHE
3、ETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Shelly Jenkins DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Steve Duncan THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Greg A. Lude MICROCIRCUIT, HYBR
4、ID, LINEAR, POWER, OPERATIONAL AMPLIFIER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-03-06 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-90679 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E046-12Provided by IHSNot for ResaleNo reproduction or networking permitted without l
5、icense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90679 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of ca
6、se outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 90679 01 H X X Federal RHA Device
7、 Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall
8、be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 PA02M Power operational amplifier 1.2.3 Device class designator. This device class d
9、esignator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class
10、 Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of t
11、he standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Desi
12、gnates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken wi
13、ll not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follo
14、ws: Outline letter Descriptive designator Terminals Package style X See figure 1 8 Flange mount 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING S
15、IZE A 5962-90679 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. Supply voltage (VS) . 19 V dc Output current (IO) . 5 A Power dissipation (PD) 1/ 2/ . 48 W Input voltage (differential) . 19 V dc - 5 V Input voltage (common
16、 mode) 19 V dc - 2 V Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +150C Storage temperature range . -65C to +150C 1.4 Recommended operating conditions. Supply voltage (VS) . 15 V dc Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Govern
17、ment specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATI
18、ONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircui
19、t Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event
20、of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individua
21、l item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicabl
22、e device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function
23、 of the device for the applicable device class. 1/ Derate at 2.6C/W above case temperature (TC) of +25C. 2/ TC +25C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90679 DLA LAND AND MARITIME COLUMBUS, OHIO
24、43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and fi
25、gure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temp
26、erature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be
27、 marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format)
28、from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the m
29、anufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA La
30、nd and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VER
31、IFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening.
32、 Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either
33、 DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 10
34、15 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. c. Constant acceleration may be performed after burn-in upon approval by the qua
35、lifying activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90679 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance character
36、istics. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Quiescent current IQVIN= 0 V dc, VS= 15 V , RCL= 1.0 , VCM= 0 V dc 1/ 1 01 40 mA 2,3 60 Input offset voltage VOSVIN= 0 V dc, G = 100, VS= 15 V dc , RCL= 1.0 1/ 1 01 -10 +10 mV
37、 2 -15 +15 3 -14 +14 VIN= 0 V dc, G = 100, VS= 7 V dc , RCL= 1.0 1/ 1 -11.6 +11.6 mV 2 -16.6 +16.6 3 -15.6 +15.6 VIN= 0 V dc, G = 100, VS= 19 V dc , RCL= 1.0 1/ 1 -10.8 +10.8 mV 2 -15.8 +15.8 3 -14.8 +14.8 Input bias current, +IN +IBVIN= 0 V dc, RBIAS 100 M, VS= 15 V dc 1 01 200 pA 2 30 nA 3 200 pA
38、Input bias current, -IN -IBVIN= 0 V dc, RBIAS 100 M, VS= 15 V dc 1 01 200 pA 2 30 nA 3 200 pA Input offset currentIOSVIN= 0 V dc, RBIAS 100 M, VS= 15 V dc 1 01 100 pA 2 10 nA 3 100 pA Output voltage VOVS= 9 V dc, IO= 5 A, RL= 1 , TC= +25C and -55C 4,6 01 5 V VS= 7 V dc, IO= 3 A, RL= 1 , TC= +125C 5
39、3 V VS= 19 V dc, IO= 36 mA, RL= 500 4,5,6 18 V VS= 12 V dc, IO= 2 A, RL= 5 4,5,6 10 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90679 DLA LAND AND MARITIME COLUMBUS, OHIO
40、43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Current limits ICLRL= 5.0 , RCL= 1.0 , VS= 9 V dc, TC= +25C 1/ 4
41、 01 0.54 0.86 A Stability/noise ENG = 1, VS= 15 V dc, CL= 1.5 nF 4,5,6 01 1 mV Slew rate SRRL= 500 , VS= 18 V dc, VIN 4 VP-P 4,6 01 13 100 V/s 5 8.5 100 Open loop gain AOLRL= 500 , VS= 15 V dc, f = 15 Hz, VIN 0.2 VP-P 4,5,6 01 86 dB Common mode rejection CMR VS= 8.25 V dc, f = dc, VCM= 2.25 V dc 4,5
42、,6 01 70 dB 1/ A current limiting resistor (RCL) is connected between CL terminals and the VSterminals during these tests. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90679 DLA LAND AND MARITIME COLUMBUS,
43、 OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Min Max Min Max A 38.35 39.37 1.510 1.550 B 19.30 19.81 .760 .780 C 5.59 6.35 .220 .250 D 0.97 1.07 .038 .042 E 2.03 2.54 .080 .100 F 40 BSC 40 BSC G 12.7 BSC .500 BSC H 30.15 BSC 1.187 BSC J 15
44、.06 BSC .593 BSC K 11.68 12.70 .460 .500 Q 3.84 4.09 .151 .161 R 25.15 25.65.990 1.010 NOTES: 1. The U. S. preferred system of measurement is the metric SI. This case outline was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound uni
45、ts, the inch-pound shall take precedence. 2. Pin numbers are for reference and may not be marked on package. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90679 DLA LAND AND MARIT
46、IME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outline X Terminal number Terminal symbol 1 2 3 4 5 6 7 8 +Current limit (CL+) +VSOutput Output -IN +IN -VS -Current limit (CL-) FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproducti
47、on or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90679 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with
48、 MIL-PRF-38534, group A test table) Interim electrical parameters Final electrical parameters 1*, 2, 3, 4, 5, 6 Group A test requirements 1, 2, 3, 4, 5, 6 Group C end-point electrical 1/ parameters 1, 2, 3, 4 End-point electrical parameters for radiation hardness assurance (RHA) devices Not applicable 1/ As a minimum, for
