1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R002-93. 92-10-05 Monica L. Poelking B Redrawn with changes. Update drawing to current requirements. Editorial changes throughout. - gap 09-11-10 Charles F. Saffle The original first sheet of this drawing has b
2、een replaced. REV SHET REV SHET REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Larry T. Gauder DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR
3、 USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Tim H. Noh APPROVED BY D. R. Cool MICROCIRCUIT, DIGITAL, BIPOLAR, ADVANCED LOW POWER SCHOTTKY, TTL, 9-BIT BUS INTERFACE D-TYPE LATCHES WITH THREE STATE OUTPUTS, MONOLITHIC SILICON DRAWING APPROVAL DATE 91-05-08 AMSC N/A REV
4、ISION LEVEL B SIZE A CAGE CODE 67268 5962-90720 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E316-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90720 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990
5、REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in
6、the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90720 01 M K X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device cl
7、ass designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL
8、-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ALS29843 9-bit bus interface D-ty
9、pe latches with 3-state outputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class le
10、vel B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style K GDFP2-F24 or CDFP3-F24
11、 24 dual-in-line package L GDIP3-T24 or CDIP4-T24 24 flat package 3 CQCC1-N28 28 square chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or network
12、ing permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90720 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) -0.5 V dc to +7.0 V dc Input voltage range -1.2 V d
13、c at -18 mA to +7.0 V dc Voltage applied to a disabled 3-state output -0.5 V dc to +5.5 V dc Storage temperature range -65C to +150C Continuous power dissipation (PD) 2/ . 467.5 mW Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) 175C Thermal resistance, junction to case (JC)
14、 . See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage (VCC) 4.5 V dc minimum to 5.5 V dc maximum Maximum high level input voltage (VIH) 2.0 V dc Maximum low level input voltage (VIL) . 0.8 V dc Maximum high level output current (IOH) -18 mA Maximum low level output current (IOL) 3
15、2 mA Operating temperature range (TC) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these docu
16、ments are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Com
17、ponent Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 R
18、obbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unl
19、ess a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Continuous power dissipation is defined as VCCx ICC. Device must withstand
20、 the added PDdue to short circuit test; e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90720 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97
21、 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fi
22、t, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimension
23、s shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on fi
24、gure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Test circuit and switching waveforms. The test circuit and switching waveforms shall be specified on figure 3. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specifi
25、ed herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The
26、electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacture
27、r has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.
28、1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certif
29、icate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDB
30、K-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requir
31、ements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Noti
32、fication of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs ag
33、ent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by
34、 this drawing shall be in microcircuit group number 11 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90720 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION L
35、EVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Limits Unit Min Max High level output voltage VOHVCC= 4.5 V, VIN= 2.0 V, IOH= -12 mA 1, 2, 3 2.4 V IN= 0.8 V IOH= -18 mA 2.0 Low lev
36、el output voltage VOLVCC= 4.5 V, IOL= 32 mA, VIN= 2.0 V, VIN= 0.8 V 1, 2, 3 0.5 V Input clamp voltage VICVCC= 4.5 V, IIN= -18 mA 1, 2, 3 -1.2 V Short circuit output current IOSVCC= 5.5 V, VOUT= 0 V 1/ 1, 2, 3 -75 -250 mA Off state output current IOZHVCC= 5.5 V, VOUT= 2.7 V 1, 2, 3 50 A IOZL VCC= 5.5
37、 V, VOUT= 0.4 V -50 High level input current IIH1VCC= 5.5 V, VIN= 5.5 V 1, 2, 3 0.1 mA IIH2 VCC= 5.5 V, VIN= 2.7 V 20 A Low level input current IILVCC= 5.5 V, VIN= 0.4 V 1, 2, 3 -0.5 mA Supply current ICCVCC= 5.5 V, Outputs low 1, 2, 3 85 mA Functional tests See 4.4.1b. VCC= 4.5 V and 5.5 V 7, 8 Pro
38、pagation delay time, D to any Q tPLH1VCC= 5.0 V CL= 50 pF See figure 3 9 1 8 ns CC= 4.5 V to 5.5 V 10, 11 1 9.5 tPHL1VCC= 5.0 V 9 1 9 CC= 4.5 V to 5.5 V 10, 11 1 11 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDA
39、RD MICROCIRCUIT DRAWING SIZE A 5962-90720 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Limits Unit
40、 Min Max Propagation delay time, D to any Q tPLH2VCC= 5.0 V CL= 300 pF See figure 3 9 1 12.5 ns VCC= 4.5 V to 5.5 V 10, 11 1 16 tPHL2VCC= 5.0 V 9 1 16 VCC= 4.5 V to 5.5.V 10, 11 1 23 Propagation delay time, C to any Q tPLH3VCC= 5.0 V CL= 50 pF See figure 3 9 1 10.5 ns VCC= 4.5 V to 5.5 V 10, 11 1 12
41、 tPHL3VCC= 5.0 V 9 1 10 VCC= 4.5 V to 5.5 V 10, 11 1 12 tPLH4VCC= 5.0 V CL= 300 pF See figure 3 9 1 15 ns VCC= 4.5 V to 5.5 V 10, 11 1 19 tPHL4 VCC= 5.0 V 9 1 16 CC= 4.5 V to 5.5 V 10, 11 1 19 Propagation delay time, PRE to any Q tPLH5VCC= 5.0 V CL= 50 pF See figure 3 9 1 11 ns VCC= 4.5 V to 5.5 V 1
42、0, 11 1 14 Propagation delay time, CLR to any Q tPHL5VCC= 5.0 V 9 1 15 VCC= 4.5 V to 5.5 V 10, 11 1 19 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90720 DEFENSE SUPPLY CENTE
43、R COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Limits Unit Min Max Enable time, OC to any Q tPZH1VCC= 5.0 V CL= 50 pF Se
44、e figure 3 9 1 12 ns VCC= 4.5 V to 5.5 V 10, 11 1 14 tPZL1 VCC= 5.0 V 9 1 12 VCC= 4.5 V to 5.5 V 10, 11 1 14 tPZH2VCC= 5.0 V CL= 300 pF See figure 3 9 1 17 ns VCC= 4.5 V to 5.5 V 10, 11 1 20 tPZL2 VCC= 5.0 V 9 1 21 VCC= 4.5 V to 5.5 V 10, 11 1 23 Disable time, OC to any Q tPHZ3VCC= 5.0 V CL= 50 pF S
45、ee figure 3 9 1 14 ns VCC= 4.5 to 5.5 V 10, 11 1 17 tPLZ3 VCC= 5.0 V 9 1 11 VCC= 4.5 V to 5.5 V 10, 11 1 12 tPHZ4VCC= 5.0 V CL= 5 pF See figure 3 9 1 8 ns VCC= 4.5 V to 5.5 V 10, 11 1 12 tPLZ4 VCC= 5.0 V 9 1 8 VCC= 4.5 V to 5.5 V 10, 11 1 9 See footnotes at end of table. Provided by IHSNot for Resal
46、eNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90720 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Condi
47、tions -55C TC +125C unless otherwise specified Group A subgroups Limits Unit Min Max Setup time, data before enable C tSUVCC= 5.0 V See figure 3 9 2.5 ns VCC= 4.5 V to 5.5 V 10, 11 2.5 Hold time, data after enable C thVCC= 5.0 V 9 4.5 ns VCC= 4.5 V to 5.5 V 10, 11 4.5 Pulse duration, tWVCC= 5.0 V Se
48、e figure 3 CLR low 9 6 ns VCC= 4.5 V to 5.5 V 10, 11 10 CC= 5.0 V PRE low 9 5 VCC= 4.5 V to 5.5 V 10, 11 10 CC= 5.0 V C high 9 4 VCC= 5.5 V to 5.5 V 10, 11 8 Recovery time ( PRE or CLR ) trVCC= 5.0 V See figure 3 9 14 ns CC= 4.5 V to 5.5 V 10, 11 17 1/ Not more than one output should be shorted at one time and the duration of the short should not exceed one second. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 596
