1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout. LTG 06-04-05 Thomas M. Hess B Update boilerplate to MIL-PRF-38535 requirements. Editorial changes throughout jak. 12-03-26 Thomas M. Hess REV SHEET REV SHEET REV STAT
2、US REV B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Marcia B. Kelleher DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING CHECKED BY Thomas J. Ricciuti THIS DRAWING IS AVAILABLE FOR USE BY AL
3、L DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, DIGITAL, BIPOLAR CMOS, OCTAL BUFFER AND LINE DRIVER WITH INVERTING THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 90-10-31 AMSC N/A REVISION LEVEL B SIZE A CAGE COD
4、E 67268 5962-90742 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E218-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 223
5、4 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN).
6、When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90742 01 M R A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.
7、4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA
8、 levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54BCT240 Octal buffer and line driver with inverting three-state output
9、s, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B m
10、icrocircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dua
11、l-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted with
12、out license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc Input voltage range (VIN) -0.5 V dc to +7.0 V dc
13、Voltage applied to any output in the high state (VOUT) . -0.5 V dc to VCCVoltage applied to any output in the disabled state (VOUT) . -0.5 V dc to +5.5 V dc Current into any output in the low state . 96 mA Input clamp current (IIC) . -30 mA Storage temperature range (TSTG) . -65C to +150C Maximum po
14、wer dissipation (PD) . 602 mW 2/ Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Minimum high level input voltage (VIH)
15、. 2.0 V dc Maximum low level input voltage (VIL) . 0.8 V dc Maximum high level output current (IOH) -12 mA Maximum low level output current (IOL) +48 mA Case operating temperature range (TC) . -55C to +125C 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Exten
16、ded operation at the maximum levels may degrade performance and affect reliability. 2/ Must be able to withstand the additional PDdue to the short circuit test, e.g., IOS. The PDlimit is based upon dc values. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I
17、HS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of t
18、his drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MI
19、L-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online
20、at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing ta
21、kes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified h
22、erein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class
23、level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s)
24、. The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.
25、5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation param
26、eter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSNot f
27、or ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In add
28、ition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Ma
29、rking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. T
30、he compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6
31、.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of su
32、pply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required
33、for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product
34、 (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manu
35、facturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 126 (see MIL-PRF
36、-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance charac
37、teristics. Test Symbol Test conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max High level output voltage VOHVCC= 4.5 V VIH= 2.0 V VIL= 0.8 V IOH= -3 mA 1, 2, 3 All 2.4 V IOH= -12 mA 2.0 Low level output voltage VOLVCC= 4.5 V VIH= 2.0 V VIL= 0.8 V IO
38、L= 48 mA 1, 2, 3 All 0.55 V Input clamp voltage VICVCC= 4.5 V, IIN= -18 mA 1, 2, 3 All -1.2 V High level input current IIH1VCC= 5.5 V, VIN= 5.5 V 1, 2, 3 All 0.1 mA IIH2VCC= 5.5 V, VIN= 2.7 V 20 A Low level input current IILVCC= 5.5 V, VIN= 0.5 V 1, 2, 3 All -1.0 mA Short-circuit output current IOS1
39、/ VCC= 5.5 V, VOUT= 0.0 V 1, 2, 3 All -100 -225 mA Supply current, outputs high ICCHVCC= 5.5 V, outputs open 1, 2, 3 All 31 mA Supply current, outputs low ICCL71 Supply current, outputs disabled ICCZ9.0 Off-state output current, high level voltage applied IOZHVCC= 5.5 V, VOUT= 2.7 V 1, 2, 3 All 50 A
40、 Off-state output current, low level voltage applied IOZLVCC= 5.5 V, VOUT= 0.5 V 1, 2, 3 All -50 A Functional tests 2/ See 4.4.1b 7, 8 All Propagation delay time, mAn to mYntPLHCL= 50 pF R1 = R2 = 500 See figure 4 VCC= 5.0 V 9 All 0.5 4.8 ns VCC= 4.5 V and 5.5 V 10, 11 0.5 6.4 tPHLVCC= 5.0 V 9 All 0
41、.4 3.5 VCC= 4.5 V and 5.5 V 10, 11 0.4 4.5 Propagation delay time, output enable, mOEto mYntPZHVCC= 5.0 V 9 All 1.0 7.9 ns VCC= 4.5 V and 5.5 V 10, 11 1.0 9.2 tPZLVCC= 5.0 V 9 All 1.0 9.4 VCC= 4.5 V and 5.5 V 10, 11 1.0 10.8 See footnotes on next sheet. Provided by IHSNot for ResaleNo reproduction o
42、r networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Test conditions -55C TC +125C unle
43、ss otherwise specified Group A subgroups Device type Limits Unit Min Max Propagation delay time, output disable, mOEto mYntPHZVCC= 5.0 V 9 All 1.0 6.8 ns VCC= 4.5 V and 5.5 V 10, 11 1.0 8.5 tPLZVCC= 5.0 V 9 All 1.0 8.1 VCC= 4.5 V and 5.5 V 10, 11 1.0 10.6 1/ Not more than one output should be shorte
44、d at one time and the duration of the test condition shall not exceed one second. 2/ Functional tests shall be conducted at input test conditions of 0.4 V VIL 0.8 V and 2.0 V VIH 2.4 V for VCC= 4.5 V and is repeated for VCC= 5.5 V. Device type All Case outlines R, S, and 2 Terminal number Terminal s
45、ymbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1OE1A1 2Y41A2 2Y31A3 2Y21A4 2Y1GND 2A1 1Y42A2 1Y32A3 1Y22A4 1Y12OEVCCFIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90
46、742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Each buffer Inputs Output OEA YL H L L L H H X Z H = High voltage level L = Low voltage level Z = High-impedance state X = Irrelevant FIGURE 2. Truth table. FIGURE 3. Logic diagram. Provided by IHSNot
47、for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 FIGURE 4. Switching waveforms and test circuit. Provided by IHSNot for ResaleN
48、o reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90742 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 NOTES: 1. When measuring tPLZ and tPZL: S1 = 7.0 V. When measuring tPLH, tPHL, tPZH, and tPHZ: S1 = Open. 2. The tPZLand tPLZreference waveform is for the outpu
