1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED C Change device type 05 to a synchro-resolver to digital converter. Make changes to table I, figure 1, and 2. 95-06-09 K. A. Cottongim D Added device types 06 and 07. Added vendor CAGE S7631. Redrew entire document. 97-06-25 K. A. Cottongim E Parag
2、raph 1.22, device type 01, change synchro accuracy from 1.3 to 1.6 arc minutes. Changes in table I for device type 01. 00-08-02 Raymond Monnin F Updated drawing to reflect the current requirements of MIL-PRF-38534. -sld 03-06-03 Raymond Monnin G Rewrite paragraphs 4.2.a.2. and 4.3.3.b.2 to add TC. 0
3、4-06-18 Raymond Monnin H Table I, power supply current test, change the max limit from 30 mA to 35 mA. -gz 08-06-16 Robert M. Heber J Paragraph 1.3; Correct “Power Dissipation” (PD) for device types 01, 02, 06, and 07 from 210 mW to 245 mW, correct “Thermal resistance, junction-to-case (JC)” from “8
4、.0C/W” to “10C/W”, and delete “Thermal resistance, junction-to-ambient (JA)” Table I; “Drive Capability” test for “High impedance load” conditions for devices types 01,02,06,07 correct min value from “-1.0” to “-10”, for “Input current, INH, 14B” correct max value for device types 01,06,07 from “-10
5、” A to “-30” A, for “Input current, LBE, HBE” correct max value for device types 01,06,07 from “25” A to “30” A” mA, add reference to footnote “8/” to current test, add footnote “8/ Digital output loads will add to supply current.” to end of Table I. Update drawing paragraphs. -gc 13-02-06 Charles F
6、. Saffle THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV J SHEET 15 REV STATUS REV J J J J J J J J J J J J J J OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Donald R. Osborne DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.d
7、la.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Steve Duncan THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, HYBRID, LINEAR, 11.8 VOLTS, SYNCHRO-RESOLVER TO DIGITAL CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-08-15 A
8、MSC N/A REVISION LEVEL J SIZE A CAGE CODE 67268 5962-90820 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E067-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-9082
9、0 REVISION LEVEL J SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
10、available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 90820 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (
11、see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The de
12、vice type(s) identify the circuit function as follows: Device type Generic number Circuit function Accuracy 01 SD-14531D1-115 11.8 V, 400 Hz, S-R/D converter 1.3 arc minutes (resolver) 1.6 arc minutes (synchro) 02 SDC14531-631 11.8 V, 400 Hz, R/D converter 1.3 arc minutes (resolver) 03 HSRD1006-C148
13、/2 11.8 V, 400 Hz, S-R/D converter 1.3 arc minutes (resolver) 2.6 arc minutes (synchro) 04 HRD1006-C148A/2 11.8 V, 400 Hz, R/D converter 1.3 arc minutes (resolver) 05 HSRD1056-C775B/2 11.8 V, 400 Hz, R/D converter 1.3 arc minutes (resolver) 2.6 arc minutes (synchro) 06 SD-14531D1-114 11.8 V, 400 Hz,
14、 S-R/D converter 2.6 arc minutes (synchro) 07 SD-14531D1-112 11.8 V, 400 Hz, S-R/D converter 5.2 arc minutes (synchro/resolver) 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of
15、MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applicati
16、ons. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limit
17、ed temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING
18、DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90820 REVISION LEVEL J SHEET 3 DSCC FORM 2234 APR 97 E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the devi
19、ce acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have
20、 a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 36 Dual-in-line 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absol
21、ute maximum ratings. 1/ Supply voltage (VS) +7.0 V dc Reference input . 150 V rms Digital inputs -0.3 V dc to +7.0 V dc Power dissipation (PD): 2/ Device types 01, 02, 06, and 07 . 245 mW Device types 03 and 04 166 mW Device type 05 110 mW Storage temperature range -65C to +150C Lead temperature (so
22、ldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC). 10C/W Junction temperature (TJ) +150C 1.4 Recommended operating conditions. Supply voltage (VS) +4.5 V dc to +5.5 V dc Ambient operating temperature range(TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, s
23、tandards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hy
24、brid Microcircuits, General Specification for. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Power dissipation applies up to TC= +125C. Provided by IHSNot for Resale
25、No reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90820 REVISION LEVEL J SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-ST
26、D-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the
27、Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supe
28、rsedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the perf
29、ormance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-3853
30、4 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as spe
31、cified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Output accuracy test angles. The output accuracy test angles shall be as
32、 specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test req
33、uirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer
34、s vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for
35、each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land an
36、d Maritime-VA) upon request. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90820 REVISION LEVEL J SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performanc
37、e characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device types Limits Unit Min Max Resolution control RC 14B = logic “1“ 7,8 All 14 14 Bits 14B = logic “0“ 16 16 Accuracy repeatability 2/ AR 7,8 01,02, 06,07 -1.0 +1.0 LSB Output accuracy 3/ AOUT
38、16-bit resolution 4/ (resolver mode) 7,8 01,02, 03,04, 05 1.3 ARC-MIN 16-bit resolution 4/ (synchro mode) 01 1.6 02,03, 04,05 2.6 14-bit resolution 4/ 01,02, 03,04, 05 2.6 16-bit resolution 4/ (synchro/resolver mode) 06 2.6 07 5.2 Reference synthesizer 2/ RS Reference phase shift between the convert
39、er signal and reference inputs 4,5,6 All -45 +45 Degree Reference input Input voltage range 2/ VIN 4,5,6 01,02, 06,07 4 130 V rms 03,04, 05 20 130 Carrier frequency 2/ 4,5,6 All 360 1000 Hz See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without li
40、cense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90820 REVISION LEVEL J SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A su
41、bgroups Device types Limits Unit Min Max Reference input - Continued. Input impedance 2/ ZIN1Single ended 4,5,6 01,02, 05,06, 07 250 k 03,04 200 Differential 01,02, 05,06, 07 500 03,04 400 Common mode range 2/ CMR14,5,6 All -250 +250 V (pk) Signal input Input impedance 2/ ZIN2Line to line 4,5,6 All
42、60 k Line to ground 30 Common mode range 2/ CMR24,5,6 01,02, 06,07 -30 +30 V (pk) 03,04, 05 -25 +25 Line to line input voltage 2/ VINL-L 4,5,6 01,02, 03,04, 06,07 10.62 12.98 V rms 05 8.26 15.34 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted witho
43、ut license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 SIZE A 5962-90820 REVISION LEVEL J SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group
44、 A subgroups Device types Limits Unit Min Max Digital outputs (Bits 1-16, CB, and BIT) Drive capability VOLLogic “0“ at -1.6 mA 4,5,6 All 0.4 V dc VOHLogic “1“ at 40 A 4,5,6 01,02, 06,07 2.8 V dc 03,04 2.4 Logic “1“ at 1.6 mA 05 2.8 IZHigh impedance load 4,5,6 01,02, 06,07 -10 +10 A 03,04, 05 -10 +1
45、0 Converter busy CB Positive pulse 9,10,11 01,02, 06,07 0.8 3.0 s 03,04 0.5 3.0 05 1.1 4.0 BIT 2/ BIT Logic indicates fault, minimum error for BIT condition 7.8 All 0.5 2.0 Degree Analog output Ac error 2/ e 14 bit mode 4,5,6 01,02, 06,07 3.15 3.85 mV rms/ LSB 16 bit mode 1.55 1.93 14 or 16 bit mode
46、 03,04, 05 2.66 4.94 DC velocity voltage VEL At 2.5 rps in 16 bit resolution, positive rotation 7,8 All -1.32 V dc See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING DLA LAND AND MARITIME COLU
47、MBUS, OHIO 43218-3990 SIZE A 5962-90820 REVISION LEVEL J SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device types Limits Unit Min Max Analog output - Continued. Velocit
48、y return voltage V VL= 5.0 V 7,8 01,02, 06,07 3.44 5.16 V dc 03,04, 05 1.7 2.6 Dynamic performance Tracking rate TR 14 bit mode 7,8 01,06, 07 3600 deg/sec 16 bit mode 03,04, 05 900 Acceleration ACC 16 bit mode, TA= +25C 7 01,06, 07 264 deg/sec 14 bit mode, TA= +25C 4220 16 bit mode, TA= +25C 03,04, 05 120 Settling time 179 step, 16 bit mode 14 bit mode 7,8 01,06, 07 400 100 m sec 0.25 step, 16 bit mode 14
