1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Made technical changes to table I. 91-10-08 K. A. Cottongim B Changes in accordance with NOR 5962-R048-94 93-11-29 K. A. Cottongim C Table I, Stability/noise test, conditions column, change CLfrom 680 pF to 330 pF. Add RL= 100 . 00-08-01 Raymond
2、Monnin D Updated drawing to reflect the current requirements of MIL-PRF-38534. -sld 03-06-03 Raymond Monnin E Added footnote 1 to table II, under group C end-point electricals. Updated drawing paragraphs. -sld 11-12-12 Charles F. Saffle THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV
3、SHEET REV SHEET REV STATUS REV E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Steve Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Gary Zahn THIS DRAWING IS AVAILABLE FOR USE BY ALL DEP
4、ARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, HIGH POWER, OPERATIONAL AMPLIFIER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-03-29 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-90828 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E044-12 Provided by
5、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90828 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance class
6、es as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown
7、in the following example: 5962 - 90828 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked de
8、vices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 PA10M, MIOP42115 P
9、ower operational amplifier 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listi
10、ng (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where no
11、n-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may
12、not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acqu
13、isition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case ou
14、tline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 8 Flange mount Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING
15、SIZE A 5962-90828 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) . 50 V dc Output current (IO) . 5.0 A Power dissipation(PD)
16、 2/ . 67 W Input voltage (differential) . 50 V dc - 3 V dc Input voltage (common mode) 50 V dc Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +200C Storage temperature range . -65C to +150C 1.4 Recommended operating conditions. Supply voltage (VS) . 40 V dc Case operati
17、ng temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are thos
18、e cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. D
19、EPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Buildin
20、g 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exempti
21、on has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Derate at 2.6C/W above case temperature (TC) of +25C. Provided by IHSNot for ResaleNo reproductio
22、n or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90828 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes
23、 D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, mo
24、dify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.
25、2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections
26、 shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electri
27、cal test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the
28、manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot
29、sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity
30、(DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers prod
31、uct meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspecti
32、on procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The fo
33、llowing additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon re
34、quest. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test
35、 parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A
36、5962-90828 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C VS= 40 V dc unless otherwise specified Group A subgroups Device type Limits Unit Min Max Supply current I
37、CLVIN= 0 V dc, G = 100, 2/ RCL= 1.0 , VCM= 0 V dc 1,2 01 30 mA 3 75 Input offset voltage VOSVIN= 0 V dc, G = 100, 2/ VS= 10 V dc , RCL= 1.0 1 01 -12.0 +12.0 mV 2 -18.5 +18.5 3 -17.2 +17.2 VIN= 0 V dc, G = 100, 2/ VS= 40 V dc , RCL= 1.0 1 -6.0 +6.0 mV 2 -12.5 +12.5 3 -11.2 +11.2 VIN= 0 V dc, G = 100,
38、 2/ VS= 45 V dc , RCL= 1.0 1 -7.0 +7.0 mV 2 -13.5 +13.5 3 -12.2 +12.2 Input bias current, +IN +IBVIN= 0 V dc, RBIAS 100 M 1 01 30.0 nA 2 70.0 3 115.0 Input bias current, -IN -IBVIN= 0 V dc, RBIAS 100 M 1 01 30.0 nA 2 70.0 3 115.0 Input offset currentIOSVIN= 0 V dc, RBIAS 100 M 1 01 30.0 nA 2 70.0 3
39、115.0 Output voltage VOVS= 45 V dc, IO= 80 mA, RL= 500 4,5,6 01 40 V VS= 30 V dc, IO= 2 A, RL= 12 4,5,6 24 V VS= 18 V dc, IO= 5 A, RL= 2.07 , TC= +25C, -55C 4,6 10 V VS= 14.3 V dc, IO= 3 A, RL= 2.07 , TC= +125C 5 6.3 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or ne
40、tworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90828 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C VS= 40 V
41、 dc Group A subgroups Device type Limits Unit unless otherwise specified Min Max Current limits ISRL= 12.0, RCL= 1.0, 2/ VS= 17 V dc, TC= +25C 4 01 0.6 0.89 A Stability/noise ENG = 1, CL= 330 pF, RL= 100 4,5,6 01 1.0 mV Slew rate SRRL= 500, VIN 4 VP-P 4,5,6 01 2.0 10.0 V/s Open loop gain AOLRL= 500,
42、 f = 15 Hz, VIN 0.4 VP-P 4,5,6 01 96 dB Common mode rejection CMR VS= 15 V dc, f = dc, VCM= 9 V dc 4,5,6 01 74 dB 1/ During all group A testing, terminal connection F. O. (pin 7) is left open. 2/ A current limiting resistor (RCL) is connected between CL+ to the output and CL- to the output during th
43、ese tests. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90828 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Min Ma
44、x Min Max A 38.35 39.37 1.510 1.550 B 19.30 19.81 .760 .780 C 7.37 .290 D 0.97 1.07 .038 .042 E 2.03 2.54 .080 .100 F 40 BSC 40 BSC G 12.7 BSC .500 BSC H 30.12 BSC 1.186 BSC J 15.06 BSC .593 BSC K 11.68 12.70 .460 .500 Q 3.84 4.09 .151 .161 R 25.15 25.65.990 1.010 NOTES: 1. The U. S. preferred syste
45、m of measurement is the metric SI. This case outline was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound shall take precedence. 2. Pin numbers are for reference and may not be marked on package. FIGURE 1. Cas
46、e outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90828 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outline X Terminal number
47、 Terminal symbol 1 2 3 4 5 6 7 8 Output +Current limit (CL+) +VS+IN -IN -VSF. O. -Current limit (CL-) FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90828 DLA LAND AND MARITIM
48、E COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters Final electrical parameters 1*, 2, 3, 4, 5, 6 Group A test requirements 1, 2, 3, 4, 5, 6 Group
