1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R. 5962-R220-94. 94-07-08 M. A. FRYE B Make changes to dimensions c, L, L1, and note 1 specified under figure 1. Redrawn. - ro 98-07-22 R. MONNIN C Make changes to VIO, CMRR, PSRR, and SSBW tests as specified under
2、table I. - ro 00-02-24 R. MONNIN D Replace reference to MIL-STD-973 with reference to MIL-PRF-38535. -rrp 08-04-08 R. HEBER REV SHET REV SHET REV STATUS REV D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY RICK C. OFFICER DEFENSE SUPPLY CENTER COLUMBUS STA
3、NDARD MICROCIRCUIT DRAWING CHECKED BY CHARLES E. BESORE COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, LOW DISTORTION, PRECISION, WIDE BANDWIDTH AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING
4、APPROVAL DATE 93-06-09 OPERATIONAL AMPLIFIER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-90868 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E106-07 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWIN
5、G SIZE A 5962-90868 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A
6、choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90868 01 M P X Federal stoc
7、k class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with
8、the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Devi
9、ce type Generic number Circuit function 01 AD9617S Low distortion, precision, wide bandwidth operational amplifier 02 AD9617T Low distortion, precision, wide bandwidth operational amplifier 03 AD9618S Low distortion, precision, wide bandwidth operational amplifier 04 AD9618T Low distortion, precisio
10、n, wide bandwidth operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN
11、class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CD
12、IP2-T8 8 Dual-in-line X See figure 1 8 Dual small outline with gullwing leads Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90868 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SH
13、EET 3 DSCC FORM 2234 APR 97 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ Supply voltages (VS) . 7 V Common mode input voltage VSDifferential input voltage . 3 V Continu
14、ous output current 2/ . 70 mA Power dissipation (PD) . 600 mW Junction temperature (TJ) . +175C Storage temperature range . -65C to +150C Lead temperature (soldering 10 seconds) +300C Thermal resistance, junction-to-case (JC): Case P . See MIL-STD-1835 Case X . 20C/W Thermal resistance, junction-to-
15、ambient (JA) . 110C/W 1.4 Recommended operating conditions. Supply voltage (VS). 5 V Operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the
16、 extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test M
17、ethod Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.da
18、ps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this
19、drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performa
20、nce and affect reliability. 2/ Output is short circuit protected to ground, but not to supplies. Continuous short circuit to ground may effect device reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 59
21、62-90868 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the
22、device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as speci
23、fied herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be i
24、n accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics and post irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and pos
25、t irradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I
26、. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device
27、. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark f
28、or device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 li
29、sted manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance s
30、ubmitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certi
31、ficate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M
32、, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to revi
33、ew the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (s
34、ee MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90868 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical
35、 performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min MaxInput offset voltage VIOTA= +25C 3/ 1 01,03 -1.1 +2.2 mV 02,04 -0.0 +1.35 Input offset voltage coefficient TCVIO4/ 1,2,3 All -4 +25 V/C Input bias curr
36、ent -IIBInverting, TA= +25C 1 01 -50 +50 A 02 -25 +25 03 -45 +45 04 -30 +30 +IIBNoninverting, TA= +25C 01 -25 +35 02 -15 +20 03 -25 +35 04 -13 +18 Input bias current TCIBInverting 4/ 1,2,3 01,02 -50 +150 nA/C coefficient 03,04 -50 +130 Noninverting 4/ All -50 +125 Common mode input +VCM1,3 01,02 1.7
37、 V voltage range 03,04 1.4 2 01,02 1.4 03,04 1.0 -VCM1,3 01,02 -1.7 03,04 -1.4 2 01,02 -1.4 03,04 -1.0 Common mode rejection CMRR VCM= 0.25 V 4 All 48 dB ratio 5,6 44 Power supply rejection ratio PSRR VS= 5 % 4,5,6 All 48 dB Output voltage swing +VOUT1,2,3 01,02 3.4 V 03,04 3.3 -VOUT01,02 -3.4 03,04
38、 -3.3 Output current IOUTRL= 50 1,2 All 60 mA 3 50 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90868 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL
39、D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min MaxPower supply quiescent +IQ1,2,3 01,02 48 mA current 03,04 43 -IQ01,02 48 03,04 43 Small
40、signal bandwidth SSBW VOUT 2 VPP4,5,6 01,02 135 MHz (-3 dB) 03,04 120 Large signal bandwidth LSBW VOUT= 4 VPP4/ 4,5,6 01,02 115 MHz (-3 dB) VOUT 5 VPP4/ 03,04 120 Amplitude of peaking GFPL 50 MHz 4,6 01,02 0.8 dB 03,04 0.6 5 01,02 1.0 03,04 1.2 Amplitude of roll off GFR 75 MHz 4,5,6 01,02 0.6 dB 03,
41、04 1.2 2nd harmonic distortion HD2 2 VPP, 4.3 MHz 4/ 4,5,6 01,02 -78 dBc 03,04 -75 2 VPP, 20 MHz 4/ 01,02 -59 03,04 -55 2 VPP, 60 MHz All -43 3rd harmonic distortion HD3 2 VPP, 4.3 MHz 4/ 4,5,6 01,02 -75 dBc 03,04 -77 2 VPP, 20 MHz 4/ 01,02 -61 03,04 -62 2 VPP, 60 MHz 01,02 -46 03,04 -54 Slew rate S
42、R VOUT= 4 V step, 4/ 9,10,11 01,02 1100 V/s measured at -2 V to +2 V 03,04 1400 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90868 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OH
43、IO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min MaxRise and fall time tR, tFVOUT= 2 V step 4/ 9,10,11 01,02 2.
44、5 ns 03,04 2.6 VOUT= 4 V step 4/ 9,10 01,02 3.3 11 3.5 VOUT= 5 V step 4/ 9,10 03,04 2.8 11 3.1 Overshoot OS VOUT= 2 V step 4/ 9,10,11 01,02 14 % 03,04 10 Settling time to 0.1 % tS1VOUT= 2 V step 4/ 9,10,11 All 15 ns VOUT= 4 V step 4/ 16 Settling time to 0.02 % tS2VOUT= 2 V step 4/ 9,10,11 All 23 ns
45、VOUT= 4 V step 4/ 24 1/ For device types 01 and 02, unless otherwise specified, AV= +3 V, VS= 5 V, feedback resistance (RF) = 400 , and load resistance (RL) = 100 . For device types 03 and 04, unless otherwise specified, AV= +10, VS= 5 V, feedback resistance (RF) = 1000 , and load resistance RL= 100
46、 . 2/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of a device terminal. 3/ Measured with respect to the inverting input. 4/ If not tested, shall be
47、 guaranteed to the limits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90868 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 AP
48、R 97 FIGURE 1. Case outline X. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90868 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 Symbol Millimeters Inches Min Max Min Max A 2.11 2.62 .083 .103 b .38 .48 .015 .019 c 0.13 BSC .005 BSC E 6.35 6.60 .250 .260 E1 4.44 - .175 - E2 8.
