1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R016-99. drw 99-01-11 Raymond Monnin B Add requirements for QD certification. Incorporate revision A N.O.R. Editorial changes throughout. - drw 02-03-28 Raymond Monnin THE FIRST PAGE OF THIS DRAWING HAS BEEN RE
2、PLACED. REV SHET REV SHET REV STATUS REV B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Sandra Rooney DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Sandra Rooney COLUMBUS, OHIO 43216 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR US
3、E BY ALL DEPARTMENTS APPROVED BY Michael A. Frye MICROCIRCUIT, LINEAR, 12-BIT, D/A CONVERTER, HIGH SPEED, MONOLITHIC AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-11-22 SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-90911 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E
4、316-02 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90911 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION
5、LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part
6、or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90911 01 M X A Federal stock class designator RHA designator (see 1.2.1) Devicetype (see 1.2.2) Device class desi
7、gnator Caseoutline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-385
8、35, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device types. The device types identify the circuit function as follows: Differential Device type Generic number Circuit function nonlinearity 01 AD9712BS 12-bit, 100
9、MSPS, ECL-compatible D/A converter 2.0 LSB 02 AD9712BT 12-bit, 100 MSPS, ECL-compatible D/A converter 1.5 LSB 03 AD9713BS 12-bit, 80 MSPS, TTL-compatible D/A converter 2.0 LSB 04 AD9713BT 12-bit, 80 MSPS, TTL-compatible D/A converter 1.5 LSB 1.2.3 Device class designator. The device class designator
10、 is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and
11、qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDIP1-T28 or CDIP2-T28 28 dual-in-line 3 CQCC1-N28 28 square leadless chip carrier 1.2.5 Lead finish. The lead f
12、inish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90911 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS
13、, OHIO 43216-5000 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/, 2/ Positive supply voltage (+VS) +6 V dc Negative supply voltage (-VS). -7 V dc Analog-to-digital ground voltage differential. 0.5 V dc Digital input voltages (D1 D12, LATCH ENABLE): Device types 01 an
14、d 02 0 V dc to -VSDevice types 03 and 04 -0.5 V dc to +VSInternal reference output current 500 A Control amplifier input voltage range 0 V dc to -4.0 V dc Control amplifier output current 2.5 mA Reference input voltage (VREF). -3.7 V dc to -VSAnalog output current. 30 mA Junction temperature (TJ) +1
15、75C Storage temperature range (case). -65C to +150C Lead temperature (soldering 10 sec). +300C Thermal resistance, junction-to-case (JC): Case outline X. 10C/W Case outline 3 . 13C/W Thermal resistance, junction-to-ambient (JA): Case outline X. 32C/W Case outline 3 . 41C/W 1.4 Recommended operating
16、conditions. Ambient operating temperature range (TA) -55C to +125C Positive supply voltage range. VS5% Power dissipation (PD): Device types 01 and 02 728 mW (typical) Device types 03 and 04 784 mW (typical) 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following
17、 specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in th
18、e solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTM
19、ENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unl
20、ess otherwise specified, absolute maximum ratings are given at TA= +25C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90911 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 4
21、 DSCC FORM 2234 APR 97 (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of
22、 this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device cl
23、asses Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class
24、M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. This drawing has been modified to allow the manufacturer to use the alternate die/fabrication requirements of paragraph A.3.2.2 of MIL-PRF-38535 or other alternative approved by the Qua
25、lifying Activity. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall
26、 be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Functional block diagram. The functional block diagram shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits
27、. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroup
28、s specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is
29、 not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shal
30、l be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. For class Q
31、product built in accordance with A.3.2.2 of MIL-PRF-38535 or other alternative approved by the Qualifying Activity, the “QD” certification mark shall be used in place of the “QML” or “Q” certification mark. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall
32、be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein).
33、The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, a
34、ppendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for dev
35、ice class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the
36、 acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawin
37、g shall be in microcircuit group number 56 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90911 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET
38、 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxDifferential nonlinearity DNL 4 01, 03 1.5 LSB 5, 6 2.0 4 02, 04 1.0 5, 6 1.5 Integral nonlinearity INL 4 01,
39、03 1.75 LSB 5, 6 2.0 4 02, 04 1.25 5, 6 1.75 Zero-scale offset error IZ1 All 2.5 A 2, 3 5.0 Full-scale gain error AEFS1 All 5 % 2, 3 8.0 Internal reference voltage VIR1 All -1.11 -1.25 V 2, 3 -1.09 -1.27 Internal reference output current IIR2/ 1 All -50 500 A Output compliance range VOC2/ 1 All -1.2
40、 2 VOutput resistance RO2/ 1 All 2.0 3.0 k Output update rate 3/ 2/ 9 01, 02 100 MSPS 03, 04 80 Digital logic “1” input voltage VIH1, 2, 3 01, 02, -1.0 V 03, 04 2.0 Digital logic “0” input voltage VIL1, 2, 3 01, 02, -1.5 V 03, 04 0.8 See footnotes at end of table. Provided by IHSNot for ResaleNo rep
41、roduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90911 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - continued. Test Symbol Conditions 1
42、/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxDigital logic “1” input current IIH1, 2, 3 All 20 A Digital logic “0” input current IIL1, 2, 3 01, 02, 10 A 03, 04 600 Input setup time 4/ tS2/ 9 All 0.5 nsInput hold time 5/ tH2/ All 1.8 nsLatch pulse width
43、(LOW) (transparent) tLPW2/ 9 All 2.5 ns +VSsupply current +IS1 03, 04 12 mA 2, 3 14 -VSsupply current -IS1 01, 02 178 mA 2, 3 183 1 03, 04 184 2, 3 188 Power supply rejection ratio 6/ PSRR 4 All 125 A/V 1/ +VS= +5 V; -VS= -5.2 V; reference voltage = -1.2 V; RSET= 7.5 k; VOUT= 0 V (virtual ground), u
44、nless otherwise specified. 2/ Specification is guaranteed, but not tested. 3/ Data registered into DAC accurately at this rate; does not imply settling to 12-bit accuracy. 4/ Data must remain stable for specified time prior to falling edge of LATCH ENABLE signal. 5/ Data must remain stable for speci
45、fied time prior to rising edge of LATCH ENABLE signal. 6/ Measured at 5% of +VS(device types 03 and 04) and -VS(all device types) using external reference. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-9091
46、1 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device type All Case outline X, 3 Terminal number Terminal symbol 1 D22 D33 D44 D55 D66 D77 D88 D99 D1010 D1111 D12(LSB) 12 DIGITAL -VS 13 ANALOG RETURN 14 IOUT15 ANALOG -VS16 OUTI 17 REFERENCE
47、IN 18 CONTROL AMP OUT 19 CONTROL AMP IN 20 REFERENCE OUT21 DIGITAL -VS22 REFERENCE GROUND 23 DIGITAL +VS24 RSET25 ANALOG -VS26 LATCH ENABLE 27 DIGITAL GROUND 28 D1(MSB) FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-S
48、TANDARD MICROCIRCUIT DRAWING SIZE A 5962-90911 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 FIGURE 2. Functional block diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90911 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedur
