1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change dimensions for case outline X. Changes in accordance with NOR 5962-R171-93. Technical and editorial changes throughout. 93-07-01 M. A. FRYE B Change vendor similar part number for the 01 device. Editorial changes throughout. 94-06-10 M. A.
2、 FRYE C Drawing update to reflect current requirements. Make change to drawing description. - ro 00-07-07 R. MONNIN D Made change to replace reference to MIL-STD-973 with reference to MIL-PRF-38535. - ro 03-03-26 R. MONNIN E Add device type 02 and case outline Y. Make changes to 1.2.4, 1.3, TABLE I,
3、 and figure 2. - ro 06-03-16 R. MONNIN F Made correction to VREFtest condition in table I from IR= 20 A to IR= 20 mA. Made correction to the limits of the minimum operating current test, IC, in table I. -rrp 08-06-16 R. HEBER REV SHET REV SHET REV STATUS REV F F F F F F F F F F F F OF SHEETS SHEET 1
4、 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK C. OFFICER DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY CHARLES E. BESORE COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHALE A. FRYE AND AGENCIES OF T
5、HE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-01-07 MICROCIRCUIT, LINEAR, VOLTAGE REFERENCE, ADJUSTABLE, MONOLITHIC SILICON AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 5962-90914 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E423-08 Provided by IHSNot for ResaleNo reproduction or networking perm
6、itted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90914 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (dev
7、ice classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as show
8、n in the following example: 5962 - 90914 01 M X X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices me
9、et the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The
10、 device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LM185BY Adjustable voltage reference diode with temperature coefficient 02 LM185B Adjustable voltage reference diode 1.2.3 Device class designator. The device class designator is a single letter
11、identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL
12、-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 3 Can Y GDFP1-G10 10 Flat pack with gull wing leads 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The
13、lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90914 DEFENSE SUPPLY CENTER COLUMBUS CO
14、LUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Reverse current (IR) 30 mA Forward current (IF) 10 mA Power dissipation (PD) 113 mW Lead temperature (soldering, 10 seconds) : Cases X and 2 . +300C Case Y . +260C Storage temperature range . -55C
15、 to +125C Junction temperature (TJ) . +175C Thermal resistance, junction-to-case (JC): Case X . 80C/W Case Y . 23C/W Case 2 . 25C/W Thermal resistance, junction-to-ambient (JA): Case X . 440C/W Case Y . 194C/W Case 2 . 100C/W 1.4 Recommended operating conditions. Ambient operating temperature range
16、(TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the soli
17、citation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT
18、OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Phila
19、delphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been
20、 obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MIC
21、ROCIRCUIT DRAWING SIZE A 5962-90914 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified he
22、rein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class l
23、evel B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. T
24、he case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performan
25、ce characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgro
26、up are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking
27、the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark.
28、 The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be req
29、uired from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The ce
30、rtificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendi
31、x A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device cl
32、ass M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity
33、retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microc
34、ircuit group number 59 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90914 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 5 DSCC FORM 2234 A
35、PR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxVREFIR= 100 A 1 01,02 1.228 1.252 V Reference breakdown voltage 2,3 1.215 1.255 IR= 9 A 1 1.228 1.252 IR= 10 A 2,3 1.215 1.255 IR
36、= 1 mA 1 1.228 1.252 2,3 1.215 1.255 IR= 20 mA 1 1.228 1.252 2,3 1.215 1.255 IR= 100 A, VR= 5.3 V 1 1.228 1.252 2,3 1.215 1.255 IR= 45 A, VR= 5.3 V 1 1.288 1.252 IR= 50 A, VR= 5.3 V 2,3 1.215 1.255 IR= 1 mA, VR= 5.3 V 1 1.288 1.252 2,3 1.215 1.255 IR= 20 mA, VR= 5.3 V 1 1.288 1.252 2,3 1.215 1.255 V
37、REF/ 9 A IR 1 mA 1 01,02 -1.0 1.0 mV Reverse breakdown voltage change with current IR10 A IR 1 mA 2,3 -1.5 1.5 1 mA IR 20 mA 1 -10 10 2,3 -20 20 45 A IR 1 mA, VR= 5.3 V 1 -1.0 1.0 50 A IR 1 mA, VR= 5.3 V 2,3 -1.5 1.5 1 mA IR 10 mA, 1 -10 10 VR= 5.3 V 2,3 -20 20 See footnotes at end of table. Provide
38、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90914 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued
39、. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxVREF/ IR= 100 A, VR= 5.3 V 1 01,02 -3 3 mV Reverse breakdown voltage change with output voltage IOUT2,3 -6 6 Feedback current IF IR= 9 A 1 01,02 20 nA IR= 10 A 2,3 25 IR= 20 mA 1 20
40、2,3 25 IR= 45 A, VR= 5.3 V 1 20 IR= 50 A, VR= 5.3 V 2,3 25 IR= 20 mA, VR= 5.3 V 1 20 2,3 25 ICVR= VREF1 01,02 9 A Minimum operating current 2,3 10 VR= 5.3 V 1 45 2,3 50 Average temperature coefficient TCIR= 100 A 2/ 1,2,3 01 50 ppm/C 1/ The algebraic convention, whereby the most negative value is a
41、minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional current flow out of device terminal. 2/ The average temperature coefficient is defined as the maximum deviation of reference voltage at all measured temperatures between the operating
42、 TMINand TMAX, divided by TMAX TMIN. The measured temperatures are -55C, -40C, 0C, +25C, +70C, +85C, and +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90914 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, O
43、HIO 43218-3990 REVISION LEVEL F SHEET 7 DSCC FORM 2234 APR 97 Case X FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90914 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVI
44、SION LEVEL F SHEET 8 DSCC FORM 2234 APR 97 Case X Symbol Inches Millimeters Notes Min Max Min Max A .080 .105 2.03 2.67 b .016 .019 0.406 0.483 2 D .209 .219 5.31 5.56 D1 .178 .195 4.52 4.95 e .100 T.P. 2.54 T.P. 4 e1 .050 T.P 1.27 T.P. 4 F .030 .76 k .036 .046 0.91 1.17 k1 .028 .048 0.71 1.22 3 L .
45、500 12.70 L1 .025 0.635 45 T.P. 45 T.P. 4 NOTES: 1. The U.S. government preferred system of measurement is the metric S.I. system. However, since this item was originally designed using inch-pound units measurement, in the event of conflict between the metric and inch-pound units, the inch-pound uni
46、ts shall take precedence. 2. b (all leads) applies to L1. Diameter is uncontrolled in L1 and beyond .500 inch (12.70 mm) from the reference plane. 3. Measured from the maximum diameter of the product. 4. Leads having a maximum diameter .019 inch (0.48 mm) measured in gauging plane .054 inch (1.37 mm
47、) + .001 inch (0.03 mm) - .000 inch (0.00 mm) below the base plane of the product shall be within .007 inch (0.18 mm) of their true position relative to a maximum width tab. 5. The product may be measured by direct methods or by gauge. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleN
48、o reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90914 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 9 DSCC FORM 2234 APR 97 Device types 01 02 Case outlines X 2 Y Terminal number Terminal symbol 1 ADJUST INPUT- NC 2 OUTPUT+ NC NC 3 INPUT- NC NC 4 - NC NC 5 - NC INPUT- 6 - ADJUST NC 7 - NC ADJUST 8 - NC NC 9 - NC NC 10 - NC OUTPUT+ 11 -
