DLA SMD-5962-91773 REV D-2011 MICROCIRCUIT HYBRID LINEAR 5-VOLT SINGLE CHANNEL DC DC CONVERTER.pdf

上传人:rimleave225 文档编号:700088 上传时间:2019-01-01 格式:PDF 页数:11 大小:72.94KB
下载 相关 举报
DLA SMD-5962-91773 REV D-2011 MICROCIRCUIT HYBRID LINEAR 5-VOLT SINGLE CHANNEL DC DC CONVERTER.pdf_第1页
第1页 / 共11页
DLA SMD-5962-91773 REV D-2011 MICROCIRCUIT HYBRID LINEAR 5-VOLT SINGLE CHANNEL DC DC CONVERTER.pdf_第2页
第2页 / 共11页
DLA SMD-5962-91773 REV D-2011 MICROCIRCUIT HYBRID LINEAR 5-VOLT SINGLE CHANNEL DC DC CONVERTER.pdf_第3页
第3页 / 共11页
DLA SMD-5962-91773 REV D-2011 MICROCIRCUIT HYBRID LINEAR 5-VOLT SINGLE CHANNEL DC DC CONVERTER.pdf_第4页
第4页 / 共11页
DLA SMD-5962-91773 REV D-2011 MICROCIRCUIT HYBRID LINEAR 5-VOLT SINGLE CHANNEL DC DC CONVERTER.pdf_第5页
第5页 / 共11页
点击查看更多>>
资源描述

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R179-95. 95-08-07 Kendall A. Cottongim B Update drawing boilerplate. Editorial changes throughout. 03-06-16 Raymond Monnin C Correct paragraphs 4.2.a.2. and 4.3.3.b.2. Figure 1, correct case outline diagram. -g

2、z 07-03-01 Joseph Rodenbeck D Table II, add note to Group C end-point test parameters. Paragraphs 4.2.a.2 and 4.3.3.b.2, reinstate original paragraphs. Update boilerplate paragraphs. -gz 11-05-04 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8

3、 9 10 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, 5-VOLT, SINGLE CHA

4、NNEL, DC/DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-06-23 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-91773 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E324-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

5、,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91773 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and le

6、ad finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 91773 01 H Z X Federal RHA Device Device Case Lead

7、stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the

8、 appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function 01 AHV2805SF/CH DC/DC converter, 15 W, 5 V output 1.2.3 Device class designator. This device class designator s

9、hall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device per

10、formance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard

11、 military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devi

12、ces which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adve

13、rsely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-ST

14、ANDARD MICROCIRCUIT DRAWING SIZE A 5962-91773 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline. The case outline are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style Z See figu

15、re 1 10 Flange mount 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +50 V dc (continuous), 80 V (100 ms) Power dissipation (PD) . 10 W Lead temperature (soldering, 10 seconds) +300C Storage temperature rang

16、e -65C to +150C 1.4 Recommended operating conditions. Input voltage range . +16 V dc to +40 V dc Output power 2/ 15 W Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbo

17、oks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDA

18、RDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are availab

19、le online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this

20、drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade perform

21、ance and affect reliability. 2/ Derate output power linearly above case temperature +125C to 0 at +135C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91773 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 R

22、EVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as design

23、ated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device

24、 class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.

25、1 Case outline. The case outline shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram. The block diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless

26、 otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tes

27、ts for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general

28、performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all

29、 parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of c

30、ompliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of confo

31、rmance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufac

32、turers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Te

33、st condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and powe

34、r dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TCas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parame

35、ter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91773 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DS

36、CC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 5%, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTIOUT= 0 1 01 4.95 5.05 V 2,3 4.90 5.10 Output adjust 1/ VOAPin 3 shorted to

37、pin 4 1,2,3 01 4 6 % Output current 2/ IOUTVIN= 16, 28, and 40 V dc 1,2,3 01 0.0 3000 mA Output ripple voltage 3/ VRIPVIN= 16, 28, and 40 V dc, B.W. = 20 Hz to 2 MHz 1,2,3 01 60 mV p-p Line regulation VRLINEVIN= 16, 28, and 40 V dc, IOUT= 0, 1500, and 3000 mA 1 01 5 mV 2,3 25 Load regulation VRLOADV

38、IN= 16, 28, and 40 V dc, IOUT= 0, 1500, and 3000 mA 1,2,3 01 50 mV Input current IINIOUT= 0, inhibit (pin 2) tied to input return (pin 10) 1,2,3 01 18 mA IOUT= 0, inhibit (pin 2) = open 50 Input ripple current 3/ IRIPIOUT= 3000 mA, B.W. = 20 Hz to 2 MHz 1,2,3 01 50 mA p-p Efficiency EFFIOUT= 3000 mA

39、 1 01 72 % 2,3 70 Isolation ISO Input to output or any pin to case (except pin 8) at 500 V dc, TC= +25C 1 01 100 M Capacitive load 4/ 5/ CLNo effect on dc performance, TC= +25C 4 01 500 F Power dissipation load fault PDOverload 6/ 1,2,3 01 10 W Short circuit 10 Switching frequency FSIOUT= 3000 mA 4,

40、5,6 01 450 550 kHz Output response to step transient load changes 7/ VOTLOAD1500 mA to/from 3000 mA 4 01 -300 +300 mV pk 5,6 -450 +450 0 mA to/from 1500 mA 4 01 -500 +500 5,6 -750 +750 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

41、 from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91773 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC+125C VIN= 28 V dc 5%, CL= 0 unless otherwise specif

42、ied Group A subgroups Device type Limits Unit Min Max Recovery time, step transient load changes 7/ 8/ TTLOAD1500 mA to/from 3000 mA 4,5,6 01 70 s 0 mA to/from 1500 mA 4,5,6 200 1500 mA to/from 0 mA 4,5,6 5 ms Output response transient to step line changes 5/ 9/ VOTLINE Input step 16 to 40 V dc IOUT

43、= 3000 mA 4 01 300 mV pk 5,6 450 Input step 40 to 16 V dc IOUT= 3000 mA 4,5,6 -1000 Recovery time transient step line changes 5/ 8/ 9/ TTLINEInput step from/to 16 to 40 V dc, IOUT= 3000 mA 4,5,6 01 800 s Turn on overshoot VTonOSIOUT= 0 mA 4 01 500 mV pk 5,6 550 IOUT= 3000 mA 4,5,6 550 Turn on delay

44、10/ TonDIOUT= 0 and 3000 mA 4,5,6 01 10 ms Load fault recovery 5/ TrLF4,5,6 01 10 ms 1/ The output voltage of this device can be adjusted upward by connecting pin 3 and pin 4 as follows: Output Adjustment Resistor Values Resistance, Pin 3 to 4 Output Voltage increase, % 0 390 k +1% 145 k +2% 63 k +3

45、% 22 k +4% 0 +5% 2/ Parameter guaranteed by line and load regulation tests. 3/ Bandwidth guaranteed by design. Tested for 20 kHz to 2 MHz. 4/ Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. A capacitive load in excess of the maximum limit will not di

46、sturb loop stability but may interfere with the operation of the load fault detection circuitry, appearing as a short circuit during turn-on. 5/ Parameter shall be tested as part of design characterization and after design or process changes. Thereafter, parameters shall be guaranteed to the limits

47、specified in table I. 6/ An overload is that condition with a load in excess of the rated load but less than that necessary to trigger the short circuit protection and is the condition of maximum power dissipation. 7/ Load step transition time between 2 and 10 microseconds. 8/ Recovery time is measu

48、red from the initiation of the transient to where VOUThas returned to within 1 percent of VOUT at 50 percent load. 9/ Input step transition time between 2 and 10 microseconds. 10/ Turn on delay time measurement is for either a step application of power at the input or the removal of a ground signal from the inhibit pin (pin 2) while power is applied to the input. Provided by IHSNot for ResaleNo reproduction or

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1