1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 03. Make changes to 1.2.2, 1.3, table I, and bulletin page. 93-04-23 M. A. FRYE B Make change to AVOLtest as specified under table I. 97-08-20 R. MONNIN C Drawing updated to reflect current requirements. Replaced reference to MIL-
2、STD-973 with reference to MIL-PRF-38535. -rrp 04-02-10 R. MONNIN THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV C SHET 15 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLU
3、MBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY RAJESH PITHADIA COLUMBUS, OHIO 43216 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY RAYMOND MONNIN MICROCIRCUIT, LINEAR, DUAL, CMOS, OPERATIONAL AMPLIFIER, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFE
4、NSE DRAWING APPROVAL DATE 92-10-07 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-92094 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E137-04 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted withou
5、t license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92094 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes
6、Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the fo
7、llowing example: 5962 - 92094 01 M P X Federal stock class designator RHA designator (see 1.2.1) Devicetype (see 1.2.2) Device class designator Caseoutline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-
8、PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device typ
9、e(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LMC662 Dual CMOS operational amplifier 02 LPC662 Dual low power CMOS operational amplifier 03 LMC6062 Dual micro power CMOS operational amplifier 1.2.3 Device class designator. The device class designator i
10、s a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qu
11、alification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device
12、 classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92094 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 3 DSCC F
13、ORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (V+ to V-) . 16 V dc Differential input voltage. V Either input beyond V+ or V- 0.7 V dc Output short circuit to GND . Continuous 2/ Power dissipation (PD): Device type 01 . 95 mW Device type 02 . 13.5 mW Device type 03 . 1.052 mW Stora
14、ge temperature range -65C to +150C Lead temperature (soldering, 10 seconds) +260C Junction temperature (TJ). +150C Thermal resistance, junction-to-case (JC). See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) +140C/W 1.4 Recommended operating conditions. Supply voltage range (V+) +5 V dc
15、to +15 V dc Supply voltage (V-). 0 V dc Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless othe
16、rwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General
17、Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawi
18、ngs. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and
19、the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operat
20、ion at the maximum levels may degrade performance and affect reliability. 2/ Applies to both single supply and split supply operation. Continuous short circuit operation at elevated ambient temperatures or multiple operational amplifier shorts, or both can result in exceeding the maximum allowed jun
21、ction temperatures of +150C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92094 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 I
22、tem requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as desc
23、ribed herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specifie
24、d in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electr
25、ical performance characteristics and post irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post irradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical te
26、st requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked as listed in M
27、IL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V sha
28、ll be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class
29、M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a ce
30、rtificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufactu
31、rers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for de
32、vice class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is require
33、d for any change as defined in MIL-PRF-38535, appendix A. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be ma
34、de available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 73 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted with
35、out license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92094 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits 2/ Test Symbol Conditions 1/ -55C TA +125C unless otherwise specifi
36、ed Group A subgroups Device type Min Max Unit 01,02 -3.0 3.0 mV 1 03 -350 350 V 01,02 -3.5 3.5 mV Input offset voltage VIO2,3 03 -750 750 V 01,02 -20 20 1 03 -25 25 Input bias current IIBRS= 0 2,3 All -100 100 pA 01,02 -20 20 1 03 -25 25 Input offset current IIORS= 0 2,3 All -100 100 pA 01,02 70 1 0
37、3 75 01,02 68 Common mode rejection ratio CMRR VCM= 0 V and 12 V, V+ = 15 V 2,3 03 70 dB 01,02 70 1 03 75 01,02 68 Positive power supply rejection ratio PSRR+ V+ = 5 V and 15 V, VOUT= 2.5 V 2,3 03 70 dB 1 All 84 01,02 82 Negative power supply rejection ratio PSRR- V- = 0 V and -10 V, VOUT= 2.5 V 2,3
38、 03 70 dB 1 V+ -2.3 V+ = 5 V and 15 V for CMRR 50 dB 2,3 01,02 V+ -2.6 1 V+ -2.3 Input common mode voltage range +VCMV+ = 5 V and 15 V for CMRR 60 dB 2,3 03 V+ -2.6 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN
39、DARD MICROCIRCUIT DRAWING SIZE A 5962-92094 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits 2/ Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgro
40、ups Device type Min Max Unit -0.1 V+ = 5 V and 15 V for CMRR 50 dB 1 01,02 0 -0.1 Input common mode voltage range -VCMV+ = 5 V and 15 V for CMRR 60 dB 2,3 03 0 V 1 0.258 1.3 2,3 01 0.310 1.8 mA 1 0 120 2,3 02 0 145 1 0 38 Both amplifiers, VOUT= 1.5 V 2,3 03 0 60 A 1 0.258 2.5 2,3 01 0.200 4.3 mA 1 0
41、 200 Both amplifiers, VOUT= 1.5 V, V+ = 15 V 2,3 02 0 300 1 0 47 Supply current ICCBoth amplifiers, VOUT= 7.5 V, V+ = 15 V 2,3 03 0 70 A Sourcing, VOUT= 0 V -16 Sinking, VOUT= 5 V 1 All 16 01,02 -12 Sourcing, VOUT= 0 V 03 -8 01,02 12 Output current IOUTSinking, VOUT= 5 V 2,3 03 7 mA See footnotes at
42、 end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92094 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance cha
43、racteristics - Continued. Limits 2/ Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Min Max Unit 1,2,3 01,02 -19 1 -15 Sourcing, VOUT= 0 V, V+ = 15 V 2,3 03 -9 1,2,3 01,02 19 1 24 Output current IOUTSinking, VOUT= 13 V, V+ = 15 V 2,3 3 7 mA RL= 2 k 40
44、0 Sourcing, 3/ V+ = 15 V, VOUT= 7.5 V to 11.5 V RL= 600 200 RL= 2 k 180 Sinking, 3/ V+ = 15 V, VOUT= 2.5 V to 7.5 V RL= 600 4 01 100 RL= 100 k 400 Sourcing, 3/ V+ = 15 V, VOUT= 7.5 V to 11.5 V RL= 5 k 200 RL= 100 k 180 Sinking, 3/ V+ = 15 V, VOUT= 2.5 V to 7.5 V RL= 5 k 4 02 100 RL= 100 k 400 Sourci
45、ng, 3/ V+ = 15 V, VOUT= 7.5 V to 11.5 V RL= 25 k 400 RL= 100 k 180 Large signal voltage gain AVOLSinking, 3/ V+ = 15 V, VOUT= 2.5 V to 7.5 V RL= 25 k 4 03 100 V/mV See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR
46、D MICROCIRCUIT DRAWING SIZE A 5962-92094 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits 2/ Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups
47、 Device type Min Max Unit RL= 2 k 300 Sourcing, 3/ V+ = 15 V, VOUT= 7.5 V to 11.5 V RL= 600 150 RL= 2 k 70 Sinking, 3/ V+ = 15 V, VOUT= 2.5 V to 7.5 V RL= 600 5,6 01 20 RL= 100 k 250 Sourcing, 3/ V+ = 15 V, VOUT= 7.5 V to 11.5 V RL= 5 k 150 RL= 100 k 70 Sinking, 3/ V+ = 15 V, VOUT= 2.5 V to 7.5 V RL
48、= 5 k 5,6 02 35 RL= 100 k 200 Sourcing, 3/ V+ = 15 V, VOUT= 7.5 V to 11.5 V RL= 25 k 150 RL= 100 k 70 Large signal voltage gain AVOLSinking, 3/ V+ = 15 V, VOUT= 2.5 V to 7.5 V RL= 25 k 5,6 03 35 V/mV V+ = 5 V, RL= 2 k to V+/2 4.82 V+ = 5 V, RL= 600 to V+/2 4.41 V+ = 15 V, RL= 2 k to V+/2 14.50 V+ = 15 V, RL= 600 to V+/2 4 01 13.35 V+ = 5 V, RL= 100 k to V+/2 4.97 V+ = 5 V, RL= 5 k to V+/2 4.85 V+ = 15 V, RL= 100 k to V+/2 14.92 Maximum output voltage swing +VOPV+ = 15 V, RL= 5 k to V+/2 4 02 14.68 V See footnotes at end of table. Provided by IHSNot for R
