1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update the boilerplate to current requirements as specified in MIL-PRF-38535. Editorial changes throughout. jak 06-08-24 Thomas M. Hess B Updated DC output current (ICC, IGND), add source of supply information cage 0C7V7. Update the boilerplate p
2、aragraphs to current requirements as specified in MIL-PRF-38535. jwc 13-02-25 Thomas M. Hess REV SHEET REV B B B SHEET 15 16 17 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Thanh V. Nguyen DLA LAND AND MARITIME COLUMBUS, OHIO 43218-
3、3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING CHECKED BY Thanh V. Nguyen THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ADVANCED CMOS, OCTAL D-TYPE FLIP-FLOP WITH THREE-STATE OUTPUTS, MONOLITHIC SILICON AND AGENCIES O
4、F THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-06-08 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-92179 SHEET 1 OF 17 DSCC FORM 2233 APR 97 5962-E201-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE
5、 A 5962-92179 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case
6、outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92179 01 M R A Federal stock class designat
7、or RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriat
8、e RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generi
9、c number Circuit function 01 54ACQ374 Octal D-type flip-flop with three-state outputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the re
10、quirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive desig
11、nator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Pro
12、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92179 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (V
13、CC) . -0.5 V dc to +7.0 V dc DC input voltage range (VIN) . -0.5 V dc to VCC + 0.5 V dc DC output voltage range (VOUT) -0.5 V dc to VCC+ 0.5 V dc DC input clamp current (IIK): VIN= -0.5 V . -20 mA VIN= VCC+ 0.5 V . +20 mA DC output clamp current (IOK): VOUT= -0.5 V . -20 mA VOUT= VCC+ 0.5 V +20 mA D
14、C output current (IOUT) (per output pin) . 50 mA DC VCCor GND current (ICC, IGND) (per pin) 50 mA Storage temperature range (TSTG) -65C to +150C Maximum power dissipation (PD) 500 mW Lead temperature (soldering, 10 seconds) . +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction
15、temperature (TJ) . +175C 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) . +3.0 V dc to +5.5 V dc Input voltage range (VIN) . 0.0 V to VCC Output voltage range (VOUT) 0.0 V to VCCMinimum high level input voltage (VIH): VCC= 3.0 V . 2.1 V VCC= 4.5 V . 3.15 V VCC= 5.5 V . 3.85 V
16、 Maximum low level input voltage (VIL): VCC= 3.0 V . 0.9 V VCC= 4.5 V . 1.35 V VCC= 5.5 V . 1.65 V Case operating temperature range (TC) -55C to +125C Minimum input edge rate (V/t): (VINfrom 0.3VCCto 0.7VCCor from 0.7VCCto 0.3VCC) 125 mV/ns Maximum high level output current (IOH): VCC= 3.0 V . -12 m
17、A VCC= 4.5 V . -24 mA Maximum low level output current (IOL): VCC= 3.0 V . +12 mA VCC= 4.5 V . +24 mA 1/ Stresses above the absolute maximum rating may cause permanent damage to the device, Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise n
18、oted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUI
19、T DRAWING SIZE A 5962-92179 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent s
20、pecified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Sta
21、ndard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist. dla.mil/q
22、uicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these document
23、s are those cited in the solicitation or contract. JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JESD20 - Standard for Description of 54/74ACXXXX and 54/74ACTXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Tec
24、hnology Association, 3103 North 10th Street, Suite 240S, Arlington, VA 22201-2107.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicabl
25、e laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM
26、) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and
27、physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Termi
28、nal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and
29、 test circuit shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZ
30、E A 5962-92179 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter l
31、imits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shal
32、l be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this
33、 option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V sh
34、all be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order t
35、o supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Mar
36、itime -VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of
37、conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notifica
38、tion to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime , DLA Land and Maritime s agent, and the
39、acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing
40、 shall be in microcircuit group number 38 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92179 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC F
41、ORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +3.0 VCC +5.5 V unless otherwise specified VCCGroup A subgroups Limits 3/ Unit Min Max High level output voltage 3006 VOHFor all inputs affecting outputs under
42、 test, VIN= VIHor VILFor all other inputs, VIN= VCCor GND IOH= -50 A 3.0 V 1, 2, 3 2.90 V 4.5 V 1, 2, 3 4.40 5.5 V 1, 2, 3 5.40 IOH= -12 mA 3.0 V 1 2.56 2, 3 2.40 IOH= -24 mA 4.5 V 1 3.86 2, 3 3.70 5.5 V 1 4.86 2, 3 4.70 IOH= -50 mA 4/ 5.5 V 1, 2, 3 3.85 Low level output voltage 3007 VOLFor all inpu
43、ts affecting outputs under test, VIN= VIHor VILFor all other inputs, VIN= VCCor GND IOL= 50 A 3.0 V 1, 2, 3 0.10 V 4.5 V 1, 2, 3 0.10 5.5 V 1, 2, 3 0.10 IOL= 12 mA 3.0 V 1 0.32 2, 3 0.40 IOL= 24 mA 4.5 V 1 0.36 2, 3 0.50 5.5 V 1 0.36 2, 3 0.50 IOL= 50 mA 4/ 5.5 V 1, 2, 3 1.65 Positive input clamp vo
44、ltage 3022 VIC+For input under test IIN= 18 mA 4.5 V 1, 2, 3 5.7 V Negative input clamp voltage 3022 VIC-For input under test IIN= -18 mA 4.5 V -1.2 Input current high 3010 IIHFor input under test, VIN= 5.5 V For all other inputs, VIN= VCCor GND 5.5 V 1 0.1 A 2, 3 1.0 Input current low 3009 IILFor i
45、nput under test, VIN= 0.0 V For all other inputs, VIN= VCCor GND 5.5 V 1 -0.1 A 2, 3 -1.0 Three-state output leakage current, high 3021 IOZH5/ OE = VIHor GND For all other inputs, VIN= VCCor GND VOUT= 5.5 V 5.5 V 1 0.5 A 2, 3 10.0 Three-state output leakage current, low 3020 IOZL5/ OE = VIHor GND Fo
46、r all other inputs, VIN= VCCor GND VOUT= 0.0 V 5.5 V 1 -0.5 A 2, 3 -10.0 Quiescent supply current, output high 3005 ICCHOE = GND For all other inputs, VIN= VCCor GND 5.5 V 1 8.0 A 2, 3 160 Quiescent supply current, output low 3005 ICCL5.5 V 1 8.0 A 2, 3 160 Quiescent supply current, output three-sta
47、te 3005 ICCZ5/ OE = VCCFor all other inputs, VIN= VCCor GND 5.5 V 1 8.0 A 2, 3 160 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92179 DLA LAND AND MARITIME COLUMBUS, OHIO 432
48、18-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +3.0 VCC +5.5 V unless otherwise specified VCCGroup A subgroups Limits 3/ Unit Min Max Input capacitance 3012 CINTC= +25C See 4.4.1c GND 4 12 pF Output capacitance 3012 COUT5/ 5.5 V 4 15 pF Power dissipation capacitance CPD6/ 5.0 V 4 50 pF Low level ground bounce noise VOLP7/ VIH= VCCVIL= 0.0 V TA= +25C See 4.4.1d See figure 4 5.0
