1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with notice of revision (NOR) 5962-R208-97. - jak 97-02-11 Monica L. Poelking B Update the boilerplate to current requirements as specified in MIL-PRF-38535. Editorial changes throughout. jak 07-01-24 Thomas M. Hess C Update
2、d DC output current (ICC, IGND) in section 1.3, add source of supply information cage 0C7V7. Update the boilerplate paragraphs to current requirements as specified in MIL-PRF-38535. jwc 13-03-22 Thomas M. Hess REV SHEET REV C C C C C C SHEET 15 16 17 18 19 20 REV STATUS REV C C C C C C C C C C C C C
3、 C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING CHECKED BY Thomas J. Ricciuti THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Moni
4、ca L. Poelking MICROCIRCUIT, DIGITAL, ADVANCED CMOS, OCTAL TRANSPARENT LATCH WITH THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-06-07 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-92188 SHEET 1 OF 20 DSCC FOR
5、M 2233 APR 97 5962-E263-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92188 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing
6、 documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Har
7、dness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92188 01 M R A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3)
8、/ Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropria
9、te RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ACTQ373 Octal transparent latch with three-state outputs, TTL compatible inputs 1.2.3 Device class designator.
10、 The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix
11、 A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1
12、-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT
13、 DRAWING SIZE A 5962-92188 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+ 0.5 V dc DC output voltage range (VOUT) .
14、-0.5 V dc to VCC+ 0.5 V dc DC input diode current (IIK) (VIN= -0.5 V and VCC+ 0.5 V dc) 20 mA DC output diode current (IOK) (VOUT= -0.5 V and VCC+ 0.5 V dc) 20 mA DC output current (IOUT) (per output pin) 50 mA DC VCCor GND current (ICC, IGND) (per pin) . 50 mA Storage temperature range (TSTG) . -65
15、C to +150C Maximum power dissipation (PD) . 500 mW Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ). +175C 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Input voltage
16、 range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT) . +0.0 V dc to VCCMaximum low level input voltage (VIL) 0.8 V Minimum high level input voltage (VIH) . 2.0 V Case operating temperature range (TC) . -55C to +125C Minimum input edge rate (V/t): (from VIN= 0.8 V to 2.0 V, 2.0 V to 0.8 V) . 125
17、mV/ns Maximum high level output current (IOH) -24 mA Maximum low level output current (IOL) 24 mA 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless o
18、therwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-
19、STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the St
20、andardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. The maximum junction temp
21、erature may be exceeded for allowable short duration burn-in screening conditions in accordance with method 5004 of MIL-STD-883. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temp
22、erature range of -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92188 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2.2 Non-Government publicat
23、ions. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. JEDEC SOLID STATE TECHNOLOGY ASSOCIATION (JEDEC) JESD78 - IC Latch-Up Test. JESD20 - Standard for De
24、scription of 54/74ACXXXX and 54/74ACTXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10th Street, Suite 240S, Arlington, VA 22201-2107). 2.3 Order of precedence. In the event of
25、 a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual
26、item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item
27、 requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for
28、 device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as
29、specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and test circuit shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and tes
30、t circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full c
31、ase operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the m
32、anufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for de
33、vice classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The complianc
34、e mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92188 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET
35、5 DSCC FORM 2234 APR 97 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be re
36、quired from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets
37、, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MI
38、L-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required
39、 for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore docume
40、ntation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 38 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networ
41、king permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92188 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -5
42、5C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type 3/ and device class VCCGroup A subgroups Limits 4/ Unit Min Max High level output voltage 3006 VOH1For all inputs affecting output under test VIN= VIHor VILVIH= 2.0 V VIL= 0.8 V For all other inputs VIN= VCCor GND IOH= -50 A All All
43、4.5 V 1, 2, 3 4.40 V VOH2For all inputs affecting output under test VIN= VIHor VILVIH= 2.0 V VIL= 0.8 V For all other inputs VIN= VCCor GND IOH= -50 A All All 5.5 V 1, 2, 3 5.40 VOH3For all inputs affecting output under test VIN= VIHor VILVIH= 2.0 V VIL= 0.8 V For all other inputs VIN= VCCor GND IOH
44、= -24 mA All All 4.5 V 1 3.86 2, 3 3.70 VOH4For all inputs affecting output under test VIN= VIHor VILVIH= 2.0 V VIL= 0.8 V For all other inputs VIN= VCCor GND IOH= -24 mA All All 5.5 V 1 4.86 2, 3 4.70 VOH55/ For all inputs affecting output under test VIN= VIHor VILVIH= 2.0 V VIL= 0.8 V For all othe
45、r inputs VIN= VCCor GND IOH= -50 mA All All 5.5 V 1, 2, 3 3.85 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92188 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEV
46、EL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type 3/ and device class VCCGroup A subgroups Limits 4/ Unit Min Max Low level
47、 output voltage 3007 VOL1For all inputs affecting output under test VIN= VIHor VILVIH= 2.0 V VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= 50 A All All 4.5 V 1, 2, 3 0.10 V VOL2For all inputs affecting output under test VIN= VIHor VILVIH= 2.0 V VIL= 0.8 V For all other inputs VIN= VCCor GND IO
48、L= 50 A All All 5.5 V 1, 2, 3 0.10 VOL3For all inputs affecting output under test VIN= VIHor VILVIH= 2.0 V VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= 24 mA All All 4.5 V 1 0.36 2, 3 0.50 VOL4For all inputs affecting output under test VIN= VIHor VILVIH= 2.0 V VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= 24 mA All All 5.5 V 1 0.36 2, 3 0.50 VOL55/ For all inputs affecting output under test VIN= VIHor VILVIH= 2.0 V VIL= 0.8 V For all other inputs VIN= VCCor GND IOL= 50 mA All All 5.5 V 1, 2, 3 1.65 See footnotes at end of table. Provided by
