1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R055-94. 93-11-30 Kendall A. Cottongim B Paragraph 4.2.a.2, correct TCto TA. Table II, Interim electrical parameters, delete subgroup 7. Update drawing boilerplate. 06-05-04 Raymond Monnin C Updated drawing par
2、agraphs. -sld 12-04-10 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Steve L. Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY M
3、ichael Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, VOLTAGE REGULATOR AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-11-27 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-93134 SHEET 1 OF 11 DSCC F
4、ORM 2233 APR 97 5962-E166-12Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93134 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawin
5、g documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the
6、PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 93134 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness a
7、ssurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic numbe
8、r Circuit function 01 ARX5006, CJSE298 Voltage regulator 02 ARX5007, CJSE299 Voltage regulator 03 ARX5008, CJSE300 Voltage regulator 04 ARX5009, CJSE301 Voltage regulator 05 ARX5010, CJSE321 Voltage regulator 06 ARX5011, CJSE322 Voltage regulator 1.2.3 Device class designator. This device class desi
9、gnator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class De
10、vice performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the
11、standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designa
12、tes devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will
13、not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
14、S-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93134 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package st
15、yle X See figure 1 2 Can (glass lead seal) 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage (VIN) 30 V dc continuous Input voltage (VIN) 36 V dc for 100 ms Operating junction temperature . +150 C Storage temperature -65 C to +1
16、50 C Maximum thermal resistance, each pass transistor . 1.0 C/W Maximum weight 15 grams 1.4 Recommended operating conditions. Input voltage range 17.5 V dc to 25 V dc Case operating temperature range (TC) -55 C to +125 C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks.
17、 The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, Gene
18、ral Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircu
19、it Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing
20、 and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device cla
21、sses D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate
22、, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class
23、. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT
24、DRAWING SIZE A 5962-93134 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The
25、case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Test circuit(s). The test circuit(s) shall be as specified on figure 3 and 4. 3.3 Electrical performance characteristics. Unless otherw
26、ise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for
27、each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general per
28、formance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all pa
29、rameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of com
30、pliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of confor
31、mance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufact
32、urers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Tes
33、t condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and powe
34、r dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parame
35、ter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93134 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DS
36、CC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55 C TC +125 C See figure 3 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Load regulation VRLoad VIN= +17.5 V, IO1= 0 A, IO2= +1.0 A 1,2,3 01 4.9 5.1 V Load regulation VRLoad V
37、IN= -17.5 V, IO1= 0 A, IO2= -1.0 A 1,2,3 02 -5.3 -5.1 V Load regulation VRLoad VIN= +17.5 V, IO1= 0 A, IO2= +2.5 A 1,2,3 03 14.7 15.3 V Load regulation VRLoad VIN= -17.5 V, IO1= 0 A, IO2= -2.5 A 1,2,3 04 -15.3 -14.7 V Load regulation VRLoad VIN= +17.5 V, IO1= 0 A, IO2= +0.9 A, IO3= +1.2 A 1,2,3 05 4
38、.9 4.95 4.95 5.1 5.05 5.05 V Load regulation VRLoad VIN= -17.5 V, IO1= 0 A, IO2= -0.425 A, IO3= -0.624 A IO4= -1.0 A 1,2,3 06 -5.3 -5.25 -5.25 -5.3 -5.1 -5.15 -5.15 -5.1 V Line regulation VRLine VIN1= +17.5 V, VIN2= +25.0 V IO= +1.0 A 1,2,3 01,05 4.90 5.1 V Line regulation VRLine VIN1= -17.5 V, VIN2
39、= -25.0 V IO= -1.0 A 1,2,3 02,06 -5.3 -5.1 V Line regulation VRLine VIN1= +17.5 V, VIN2= +25.0 V IO= +2.5 A 1,2,3 03 14.7 15.3 V Line regulation VRLine VIN1= -17.5 V, VIN2= -25.0 V IO= -2.5 A 1,2,3 04 -15.3 -14.7 V Provided by IHSNot for ResaleNo reproduction or networking permitted without license
40、from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93134 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55 C TC +125 C See figure 3 unless otherwise specified Grou
41、p A subgroups Device type Limits Unit Min Max Ripple rejection VRR1VIN= +22.0 V, IO= +1.0 A, eIN= .2 to 2.0 VP-P, f = 150 kHz 4,5,6 01,05 45 dB Ripple rejection VRR2VIN= +18.5 V, IO= +1.0 A, eIN= .2 to 2.0 VP-P, f = 150 kHz 4,5,6 01,05 40 dB Ripple rejection VRR1VIN= -22.0 V, IO= -1.0 A, eIN= .2 to
42、2.0 VP-P, f = 150 kHz 4,5,6 02,06 45 dB Ripple rejection VRR2VIN= -18.5 V, IO= -1.0 A, eIN= .2 to 2.0 VP-P, f = 150 kHz 4,5,6 02,06 40 dB Ripple rejection VRR1VIN= +22.0 V, IO= +2.5 A, eIN= .2 to 2.0 VP-P, f = 150 kHz 4,5,6 03 45 dB Ripple rejection VRR2VIN= +18.5 V, IO= +2.5 A, eIN= .2 to 2.0 VP-P,
43、 f = 150 kHz 4,5,6 03 40 dB Ripple rejection VRR1VIN= -22.0 V, IO= -2.5 A, eIN= .2 to 2.0 VP-P, f = 150 kHz 4,5,6 04 45 dB Ripple rejection VRR2VIN= -18.5 V, IO= -2.5 A, eIN= .2 to 2.0 VP-P, f = 150 kHz 4,5,6 04 40 dB Output current limit protection IOLPVIN= +22.0 V 1,2,3 01,05 +1.5 +3.5 A 03 +3.4 +
44、7.0 VIN= -22.0 V 1,2,3 02,06 -3.5 -1.5 A 04 -7.0 -3.0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93134 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE
45、 I. Electrical performance characteristics - Continued. Test Symbol Conditions -55 C TC +125 C See figure 3 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output short circuit protection IOSVIN= +22.0 V, IO= +1.0 A, Short output (pin 2) for a minimum of 1 second 1,2,3 0
46、1,05 0.1 1.0 A 03 0.1 1.2 VIN= -22.0 V, IO= -1.0 A, Short output (pin 2) for a minimum of 1 second 1,2,3 02,06 0.1 1.0 A 04 0.1 1.2 Negative output latch-up VINto device type 03 = +20 V, then apply -20 V to device type 04, see figure 4 1,2,3 03, 04 tied together -15.3 -14.7 V Positive output latch-u
47、p VINto device type 04 = = -20 V, then apply +20 V to device type 03, see figure 4 1,2,3 03, 04 tied together +14.7 +15 .3 V Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93134 DLA LAND AND MARITIME COLUMBU
48、S, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeter Inches Min Max Min Max A 8.13 .320 b 0.97 1.09 .038 .043 D 22.23 .875 e 10.67 11.18 .420 .440 e1 5.21 5.72 .205 .225 F 1.52 3.43 .060 .135 L 6.10 6.60 .240 .260 p 3.83 4.08 .151 .161 q 29.90 30.40 1.177 1.197 R 12.57 13.33 .495 .525 R1 3.32 4.77 .131 .188 S 16.63 17.14 .655 .675 FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or netwo
