1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R254-94. 94-08-05 Kendall A. Cottongim B Update drawing boilerplate to current requirements of MIL-PRF-38534. 01-05-21 Raymond Monnin C Update drawing. 05-11-09 Raymond Monnin D Table I, Power supply rejection
2、ratio (PSRR), correct test condition from VCC= VEE= 5% to VCCand VEE= 5%. Table I, Transition times (TT) test, correct subgroups 1, 2, 3 to 4, 5, 6. Transition test, correct note 3 to note 2 for subgroups 5 and 6. 05-12-07 Raymond Monnin E Table II, added note 1 to Group C end-point test parameters.
3、 Editorial changes throughout. -sld 13-09-23 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAW
4、ING CHECKED BY Michael C. Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, HIGH SPEED, HIGH VOLTAGE, VIDEO AMPLIFIER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-12-01 AMSC N/A REVISION LEVEL E SIZE A CAGE
5、 CODE 67268 5962-93246 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E203-13Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93246 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM
6、2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hard
7、ness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 93246 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3)
8、/ Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit fun
9、ction as follows: Device type Generic number Circuit function 01 MSK 1901B High voltage video amplifier 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and requir
10、e QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military
11、 quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, ma
12、nufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These excepti
13、on(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML ce
14、rtified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 24 Quad, flange mount 1.2.5 Lead finish. The lead finish shall be
15、 as specified in MIL-PRF-38534. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93246 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum rating
16、s. 1/ High voltage supply (VHV) . +65 V dc 2/ Positive supply voltage (VCC) +12 V dc Negative supply voltage (VEE) . -12 V dc Common base supply (VCB) +20 V dc Differential input voltage . 2 V dc Gain adjust input voltage range (VGAIN) -0.6 V dc to +6 V dc Offset adjust input voltage range (VOFF) -0
17、.6 V dc to +6 V dc Blank input voltage range (VBLANK) -0.6 V dc to +6 V dc Reference output current (IOUT) . 5 mA Power dissipation (PD) . 13 W Junction temperature (TJ) . +175C Thermal resistance, junction-to-case (JC) 7C/W Storage temperature range . -65C to +150C Lead temperature (soldering, 10 s
18、econds) . +300C 1.4 Recommended operating conditions. Power on sequence VHV, VCB, VCC, VEEHigh voltage supply (VHV) . +70 V dc 3/ Positive supply voltage (VCC) +10 V dc Negative supply voltage (VEE) . -10.5 V dc Common base supply (VCB) +10 V dc Input voltage (excluding VCM) 0.714 V dc Gain adjust i
19、nput voltage range (VGAIN) 0 V dc to +5 V dc Offset adjust input voltage range (VOFF) 0 V dc to +5 V dc Blank input voltage range (VBLANK) TTL levels Reference output current (IOUT) . 4 mA Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, stand
20、ards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid
21、 Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 -
22、 Standard Microcircuit Drawings. (Copies of these documents are available online at http:/quicksearch.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this
23、drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Ex
24、tended operation at the maximum levels may degrade performance and affect reliability. 2/ With respect to VCB. 3/ With respect to ground. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93246 DLA LAND AND MAR
25、ITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performan
26、ce of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 sha
27、ll be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specifie
28、d in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the
29、electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined
30、in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of M
31、IL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested,
32、and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required
33、from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of co
34、nformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (
35、QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93246 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990
36、 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Quiescent current ICC VCM= 0 V, VCC= +10 V dc (including ICB) 1,2,3 01 110 mA IEEVCM=
37、0 V, VEE= -10.5 V dc -100 Input bias current IIBVCM= 0 V 1 01 -50 +50 A 2,3 -250 +250 Blank input current IBLANK VBLANK= 0.4 V, TA= +25C 1 01 600 A VBLANK= 2.4 V, TA= +25C 400 Reference output voltage VOUTIOUT 2 mA 1,2,3 01 5.2 5.8 V Offset adjust input current IOFFVOFF= 1 V, TA= +25C 1 01 10 A Gain
38、 adjust input current IGAINVGAIN= 5 V, TA= +25C 1 01 10 A Output current blank mode IBLANK VBLANK= 2.4 V, VOFF= 1 V, VGAIN= 5 V 1,2,3 01 -2 +2 mA Output current offset (minimum) IOFFMIN VOFF= 0 V, VGAIN= 3 V 1,2,3 01 0.5 25 mA Output current offset (maximum) IOFFMAX VOFF= 5 V, VGAIN= 0 V 1 01 80 120
39、 mA 2,3 70 130 Power supply rejection ratio 2/ PSRR VCCand VEE= 5% 1,2,3 01 25 dB Common mode rejection ratio 2/ CMRR VCM= 0.5 V, f = 10 kHz 4,5,6 01 35 dB Bandwidth 2/ BW VOFF= 0 V, RL= 50 , TA= +25C 4 01 200 MHz See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or network
40、ing permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93246 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherw
41、ise specified Group A subgroups Device type Limits Unit Min Max Linearity error 2/ LE VGAIN= 1 V, VOFF= 1 V, VCM= 0.5 V, TA= +25C 4 01 -2 +2 % GS 3/ Thermal distortion 2/ thd TA= +25C 4 01 -2 +2 % GS 3/ Gain linearity 2/ AVL VIN= 0.2 V, VOFF= 1 V, VCM= 0.5 V, TA= +25C 4 01 -2 +2 % Input impedance 2/
42、 RINf = DC, either input, TA= +25C 1 01 10 k Input capacitance 2/ CINEither input, TA= +25C 4 01 2 pF Blank mode input rejection 2/ BMIR VBLANK= 2.4 V, VIN= 0.3 V, TA= +25C 4 01 2 mA Gain adjust rejection 2/ GAR VGAIN= 5 V, TA= +25C 4 01 -10 +10 mA Transconductance gm VIN= 0.6 V, VGAIN= 5 V, f = 10
43、kHz, both inputs 4,5,6 01 395 605 ms Transition times 4/ TT VIN= 0.6 V, VGain= 4 V, tr= tf 1 ns, VOFF= 1 V 4 01 4.5 ns 5,6 2/ 6 Blank input pulse width 2/ tBLANK Normal operation 4,5,6 01 30 ns 1/ VCC= +10 V dc, VEE= -10.5 V dc, VHV= +70 V dc, VCB= +10 V dc, VBLANK= 0.4 V dc, CL= 6 pF, RL= 200 , VGA
44、IN= VOFF= VIN= 0 V, unless otherwise specified. 2/ Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. 3/ GS means percent of gray scale, referring to the RS-343 standard video levels. 4/ Much faster rise times are obtainable without using test sock
45、ets. In addition a peaking network may be used to improve overall bandwidth. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93246 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC
46、 FORM 2234 APR 97 Case outline X. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93246 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 9
47、7 Case outline X - Continued. Symbol Millimeters Inches Min Max Min Max A 25.27 25.53 .995 1.005 B 3.04 3.30 .120 .130 C 18.92 19.18 .745 .755 D 4.06 4.32 .160 .170 E 16.92 17.15 .665 .675 F 0.30 0.46 .012 .018 G 6.22 6.48 .245 .255 H 12.57 12.83 .495 .505 J 2.16 2.41 .085 .095 K 18.16 18.42 .715 .7
48、25 L 25.27 25.53 .995 1.005 M 11.43 .450 N 2.03 2.29 .080 .090 P 0.20 0.30 .008 .012 Q 0.97 1.07 .038 .042 R 5.21 .205 S 2.41 2.67 .095 .105 X 12.70 .500 Y 2.62 2.97 .103 .117 NOTES: 1. The U. S. preferred system of measurement is the metric SI. This case outline was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound shall take prece
